Every new hobby brings its own unique challenges to each of us.  For me, calcuating the warp ends is my nemesis.  The pictures below describe the problem perfectly:  I always come up short some number of warp ends for my respective project which creates an unsightly imbalance at both selveges.

I've only been weaving for about 4-months now (go easy :)).  I've successfully done a few plain weave projects and I've somewhat completed a waffle weave.  This is my first attempt at overshot.

I calculated the threading repeat from the pattern as 44 warp ends.  I set this at 16 epi using 5/2 perle.  The tabby is 10/2 and pattern is 5/2 perle.  This being the tester, I wanted to use matching weft so I could see how the underlying tabby reacted with varying degress of beat pressure.  For my final product, I intend to set the warp in 8/2 perle and weft in 3/2 again using 10/2 for the tabby.  But, I clearly have some bugs to work out first.

I 'suspect' the problem may be in my sley.  I have a 10-dent and a 12-dent reed.  For this one I am using the 12-dent.  To achieve 16 epi, I sleyed in 1-1-2.  The overall project is calculated at 6 block repeats.  Assuming my math was right, 44-ends per threading sequence times 6 threading repeats is 264 warp ends.  Sleyed in 1-1-2 means I compress every 3rd reed slot or overall 25% of my warp ends leaving me with 198 warp ends in the project.  Although I only have 198 slots sleyed, I do have 264 individual heedles threaded according to the pattern and that came out spot on - not a single thread was left dangling. 

I have crunched these numbers left and right.  EIther I am missing something that is staring me right in the face, or I need to do just what I'm doing:  bend a humble knee and grovel for some pointers.  Appreciate any attempts to steer me back to the path of progress.

Pattern from Handweaver's Pattern Directory by Anne Dixon

Overall Project View:

Left Edge:

Right Edge:

Comments

Sara von Tresckow

1. It doesn't matter if you put 2 threads in a dent, they are still threaded and involved in your pattern repeats. Your sleying is fine.

2. The imbalance is more than likely due to you using 6 whold repeats without adding a few at the ending edge to form a symmetrical threading to the starting edge. When using books like the Davison, you look at how the repeat works and then check to see if you need to put, say, half those threads at the end to make things appear even.

Sara von Tresckow

I think you misunderstood what I wrote - calucalated warp ends are in the HEDDLES - you count how many threads you need for your repeat and thread them in the heddles.

The sett is how many threads are per inch - your reed controls that independently of your warp end count. If you need 250 threads for your pattern, you still have 250 threads when they are somewhat bunched up in the reed.

By sleying 1-1-2 you will get reed marks on the loom showing where the ends are doubled, but these should disappear when you wet finish the cloth. The uneven sleying could also make it look like some floats are a bit off in length - again, that should disappear after washing.

dawne

Your calculations for the number of warp ends and sleying are perfect. At first I wasn't sure what you were asking, then I took a closer look at the picture of the woven cloth from the book. I think you wantt he edges to be more balanced, and that won't happen with 6 repeats of the threading.   I went into weaving software and put the pattern in, first exactly as you have woven it with 6 repeats. 

The next picture attached is where I modified the two edges by removing 6 warp ends on the far right, and 10 on the far left.   I believe this makes the ends look more symmetrical as per the picture in the book. 

This picture is simply 6 repeats, as per the draft: 

This picture modified the two edges to remove 6 warp ends on the right and 10 on the left.  You could easily decide what exactly you wanted to have in the edges to make the left and right look like you intended. (I'm not sure my picture came out exactly right, but you get the idea). 

Submitted by hammonsr on