I have a LeClerc Mira model, older style. I was having problems keeping good tension so I bought the brake conversion kit from Camilla Valley Farm. While this has helped some, my brake drum will STILL rotate a little bit when I use my ratchet and pawl system on the front beam to tighten my warp! I know I am not supposed to need to use the friction device on the left to help with my warp tension but if I have the friction device screwed all the way down then I can achieve a tighter tension.

I had previously posted about this issue and I looked into several of the suggestions. The problem is when I try to get my threads real tight by using the ratchet and pawl on the front beam the brake drum on the warp beam actually rotates a little bit causing me not to get a super tight tension.

Now, about the amount of tightness on the warp. Maybe I am putting too much tension on my warp?? If I can get a it a real tight tension then my boat shuttles runs into all my threads in the shed.

So is this a tension issue or am I trying to achieve too tight of tension. Either way it seems that my NEW brake drum and brake circle should not move when I tighten tension on the warp.

Thanks for any input!

 

Brake Conversion KitNew Brake Conversion

Front BeamRatchet and Pawl on front beam

Brake Drum and Brake CircleBrake Drum and Brake Circle. This is what rotates (only when wanting high tension) when tightening my warp.

Friction DeviceFriction device on left side.(Warp beam advance control system)

Comments

laurafry

You may need to tighten the turnbuckle to get the tension you desire. Cheers Laura

jessiesurber

By the turnbuckle do you mean what I have been calling the 'friction device'? I didn't know the proper name. I do all the turnbuckle all the way down when I am having this problem.

jlread (not verified)

What happened to the ratchet and pawl on the right side of the warp beam....that could never slip...that friction brake that's there now will not hold a high tension.

jessiesurber

I use the ratchet and pawl on the right side to tighten my warp. The ratchet and pawl does not slip but when I move to the next cog the tension on the warp causes the brake drum on the warp beam to slip my warp forward a bit, preventing me from getting this very tight tension.

When the warp doesn't slip forward, the shed is very small and I can't fit my boat shuttle through. So I have to carefully put my shuttle through and as I keep weaving the brake drum will start to release a bit and then my sheds get larger because my tension is loosing up. So then I repeat the process of trying to tighten my warp and so it continues.

laurafry

No, the turn buckle (I may not be using the right word for it) is the gizmo with the wing nut at one end. You can turn the buckle part to shorten the length/distance between the two s hooks which will apply more tension to the brake band so the warp doesn't slip But if you have so much tension your shuttle won't pass through the shed, perhaps you have too much tension on your warp? Cheers Laura

jlread (not verified)

NO...what happened to the ratchet and pawl that was originally on the WARP beam, not the cloth beam...why did you change it out for a friction system?...and yes you are using too much tension....

jessiesurber

I never had a ratchet and pawl system on the warp beam. I talked back and forth with Nina from Camilla Valley Farms and she said what was on my loom was not original and was suprised it worked at all. She recommended getting the brake conversion kit for my loom.

ReedGuy

There would not have been a racket and pawl on the warp roller unless it was an old model. That was an old method that was abandoned. Now a ratchet system is cloth beam only with a take up handle and pawl(s). A brake drum tensions the warp beam. The turn buckle increases/decreases tension when the brake is set. You adjust tension by turning it. The wing nut I think is like a stop. You actually turn the long piece in the centre that has threaded ends. If you look at their parts site, the only ratchet on their floor looms are on the cloth beam.

jlread (not verified)

I sold a Mira several months ago, I had it for 15 ...or so many...years.  It had a ratchet and pawl on the warp beam...it never slipped...Wonder why they stopped using it as a warp beam braking system...seems silly

ReedGuy

Some looms by other makers use live weight on the warp beam and no ratchet either. I saw a photo of one in France, it had a large drum on the side with a rope wound on it and large weight on the end. Even some modern ones use this idea or similar concept. You don't have to get up from your weaving as much to fiddle with a ratchet.

jessiesurber

What I don't understand is I am only getting 26 ppi on 10/2 mercerized cotton and for my next warp I wanting to achieve between 28-20 ppi. If I can't achieve a tighter tension then I don't know how I will be able to achieve this.

I guess I will keep messing with the turnbuckle but I might email Nina to see if she has any advice.

Thanks for all your help!

SallyE (not verified)

I've been looking at your pictures.   It looks like the friction brake is installed properly, but I'm wondering if your warp isn't wound on the beam in the wrong direction.     Ususally, the warp would come from under the beam on the outside and then over the back beam.   Yours comes from the inside, which in effect, turns the friction brake up-side-down.  In this position, it won't hold the tension.

This is just a guess, from looking at your pictures.    How long is your warp?    You could try reversing it like this:   Get a piece of pipe a little longer than the warp is wide.   Put the pipe inside the warp and have a helper slowly back up as you unwind the warp.    When you get to the end, wind it on in the other direction.   This will require that you have a distance behind the loom that is half as much as your remaining warp, plus room for the person.

 

ReedGuy

Yes, I believe Sally has your solution. The warp is wound backwards.

jessiesurber

Thanks so much everyone! I emailed Nina from CamillaValleyFarms with a picture to double check and it is wound on backwards! Hopefully this will solve all my problems!

My husband assured me it would be wound on correctly when I did it that way! lol

ReedGuy

Oh well, sometimes the expert has to just pay no mind to their spouse. :D

SallyE (not verified)

The good news is that I bet you won't make that mistake again!

 

jlread (not verified)

So much for the hubbies ideas....Weavo is the GO TO.....

jessiesurber

lol! Oh well... this was just for practice this time! You are right, I won't make this mistake again!

Submitted by jessiesurber on