jenny,

I am asking you live weight questions in response to your solution for my glimakra victoria issues.

I didnt want to confuse that thread.

so let me make sure I have understood this - the live weight works by wrapping cord around one end of  the warp beam and then on the inside tying some heavy weight 13lbs  which would be off the floor but close to the floor and on the outside having a lighter weight 2lbs which would be just touching the floor.

the aim being that it would stop the warp from loosening ( as the ratchet did) but that when you wound on there would be enough slipage to mean the warp could move forward.

the aim being to get the balance right so the weights don't move much, the warp stays tense but can wind forward.

my questions are:

1.is there a problem with the warp threads snapping?

2.what happens if the weights are too heavy - does it just mean it is too hard to move forward and how do I know what the right amount of tension is

3. what sort of cord thickness should I use - is the kind you get in weaving supply shops ok

4. on the big loom you have weights on both sides but on the victoria it looks like they are just on one side - is that correct.

5. there is a thin cord with a hook and a metal washer hanging in a large V shape off the back of the loom in the photo - is that part of the weight system too?

I had thought I could also just hang a single weight on the beam that would gradually wind up onto the beam and so every while I  would have to unwind it down again - more annoying but the idea is the same and this would be perfect.

Have I understood it?

Patchwork

Comments

jennybellairs

1.  I have never had warp threads snap due to the tension.

2.  You may have to experiment around with the weights.  Having a set of barbells with interchangable weights is handy, and they actually get used, instead of sitting in a box under the bed or in a closet!  Too much weight can make it hard to turn with warp forward.  The right amount of tension should feel like when you have it locked in with your regular tension system.  The difference is when you beat.  Since it isn't locked, the warp will actually rock forward with the beat, and will fall back slightly as you move your beater back.  It takes a little getting used to because it feels different.

3.  I got my cord from the hardware store.  Get cotton, about 1/8" thick.  Don't forget, those three wraps around the backbeam will take up a little bit of space, so you don't want rope.

4.  I don't think you will need weights on both sides of the back beam on the little loom.  It would take up too much of your width.  On my bigger loom, it is just what worked out with my experimenting.  I think it was too much weight on one side, so I split it to balance the weights.

5.  The thin cord with the hook is just weighting one broken warp thread.  It wanted to spin around while just dangling, so I hooked it to something to hold it still.

The beauty of this system, especially with the short sweet spot on the Victoria, is that you can turn your warp forward every 1/4" if you wanted to from the front with no difference in your tension.  Your turning knobs are right there, so you hardly mess with your weaving rhythm.

It sounds like you are understanding the concept pretty well.  Good luck with hooking up your weights.

Jenny in Charlevoix the Beautiful

patchwork

Thanks  Jenny

sounds like the victoria does have a short weavable area after all then from your description and it is not just something to do with my loom/beater set up but like you say if you can move the warp without having to move then there isn't really an issue with this I guess. PHEW.

Do your shafts when not in use sit on the wooden side bit or are they held off it somehow with elastics as some are suggesting? not sure what that would look like.

my inherited homemade treadle set up doesnt look like the official one with two peddles and two lams so maybe there is something weird going on with that.

Thanks - will ask more if I need once I get my weights,

Patchwork

patchwork

one more thing ..

I like to do warps that are different yarns and different thicknesses (to be a bit funky) do you think there is a risk if the warp rocks forwards that it could pull the differing thickness of warp threads so they rock forward unevenly.

Does that make sense - sorry until I try it I cant think how it works/feels or what level of rock you mean!

Patchwork

jennybellairs

If your warp isn't real long, different thicknesses shouldn't make much difference.  If the tension changes on individual threads after weaving a bit, you can always weight the individual threads like I did in the photo you asked about.

I will have to go out into the studio to look at my loom, because I don't remember what my shafts are resting on, if anything.  I looked at the photos I have, but none of them show that area very well.

How many shafts does your loom have?  Mine has eight.

Jenny in Charlevoix the Beautiful

jennybellairs

It's 4 degrees and windy outside, and a balmy 60 degrees in the studio.

I did get some photos for you.  Hopefully they will help.

The first one is a close-up of the live weight tension cord around the back beam and also showing where the shafts rest on the loom (4 are up and 4 at rest).

The second photo is a side view.  I can beat a little further forward, but with the live weight tension, I wind quite often, keeping the beater in the sweet spot.

Please excuse the mess in the background.  The studio is due for a cleaning again.

By the way, who am I talking to?  I don't feel right calling you Patchwork!

Jenny in Charlevoix the Beautiful

jennybellairs.blogspot.com

ReedGuy

Yes, I can imagine it's cold up there in MI. It wasn't much above zero back east here in New Brunswick. :D Had to fix the mail box that the plow swat off the post. Weee hawww cold on the fingers handling steel tools and bolts to fix that up. Nice warm shop though to retreat to and thaw stinging fingers out. :D

Submitted by patchwork on