Hi all,

I was given a very old (1837) barn loom and have just brought it home (in pieces) today. I think it's absolutely beautiful, very primitive and seems to be in very good shape for it's age. I would love to be able to clean it before bringing it into the house and assembling it but I don't want to ruin the rustic appearance. I'm wondering if anyone here has any ideas on how to clean it? It's totally bare wood. I can get take some photos if it would help.

Thanks so much,

Robin

Comments

Woodburner

It's really great to see so many lovely old looms being brought back to life.

Bobbie, the metal toothed piece in the third picture is one of the supports for the top bar of the beater assembly. There should be one for each side, and the top beater bar should have two inset metal strips, one at each end, that point downwards and rest on the notched pieces. This allows the beater to swing freely with minimal wear to the frame. hth

sandra.eberhar…

The board with holes in it is part of the warp beam tension control.  The fork probably fits over the diagonal  brace to the back upright, slanting toward the front.  A dowel goes in one of the holes of the board and in one of the holes in the warp beam. The dowel doesn't go in either hole straight, and the friction holds the beam.   My barn loom from Georgia had this, but I changed it to a friction brake.  I had to make a new warp beam anyway, because the original was badly warped.

Sandra

kellytwo (not verified)

Thank you for your reply Sandra.  Do you have any pictures of your loom before you changed it to a friction brake?  Unfortunately my loom still isn't put together.  I really would like to get it done this summer, and hopefully you can provide the answer to my brake mystery. 

Doreen

2BobbieJ

Thanks so much for the replies, but oh dear, you've lost me on the warp beam tension and diagonal support and friction brake. I don't see anything that might go diagonally?

I've  looked at numerous pictures, but haven't seen a loom that looks quite like the one I have, but I am truly a novice. Does anyone have photos of a similar loom that's assembled? If I can see full pictures, maybe I can move forward?

I'm so thankful that I happened upon this site-now I feel like I'm making some kind of progress and that forlorn looking, disassembled loom will sing again one day!

Joanne Hall

of an older style loom can be found in the book, Foot Power Loom Weaving by Worst.  You can find this book at a library or from used book sites.  It would be a start for you.

Joanne

kellytwo (not verified)

Bobbiej, The response from Sandra was for my barn loom, (which was quite an old post).  That's why it didn't make too much sense to you when she talked about the warp beam and brake.  I'm hoping that she has some pictures of her original loom to post.  I haven't found a loom that has a brake like mine so seeing pictures will certainly help.  Good luck with your loom, it looks like quite a project.  

Woodburner

The second link doesn't work because there is a space included at the end of the URL that shouldn't be there. Nice info though, thanks. :)

2BobbieJ

 

Hello to all of my new friends. After continued research into all of the fine suggestions you've offered, I think I'm just about ready to assemble this gorgeous loom. I do have a few more questions before I dive in with earnest. In the first photo, the two side pieces are attached to the end piece which will hold the breast beam (?). The side piece facing us with the hole should hold the cloth beam. Since everything is pegged, I'd like to know if I have that side piece in the correct position or should it be flipped upside down so the hole/cloth beam will be lower? Also in the first picture, there is a spool-like object that I don't recognize in the research. Let me say that during this time, I have also discovered (to my delight) either an old quilting frame or curtain stretcher (according to the internet) was stored with the loom in the pack house-so I have at least 2 different things mixed together. So maybe the spool thing doesn't even belong with the loom? Also, just from researching, it seems that the supports which would hold the warp beam are missing altogether? Unless someone spots them in the clutter. Also, there are several long 2-3 inch wide sticks (for lack of a better term) with holes along the length of them. These sticks are long-longer that the width of the loom-are these the heddles? And lastly, there are several screen-like things that are similar to the one that is currently positioned in the beater-is it common to have interchangeable ones? Maybe for different patterns? I'm thinking that when I do plunge into the assembly, I'm going to take a photo after every piece is placed to create sort of a step by step process and I will post those. Thanks so much to everyone for all of the support. Have a super fantastic day-it's beautiful here in North Carolina!

2BobbieJ

The "first photo" of several that I refer to is 14 entries above. Thanks again!

tommye scanlin

There's a small barn frame loom used for weaving demo occasionally at the Folk Art Center in Asheville, NC. Don't know how closely it might be like your loom, though. You might ask Deb Schillo, the librarian and archivist there if she might be able to send you a photo so you could compare. You can find her contact info at the Southern Highland Craft Guild website. Tommye

2BobbieJ

I live in the beautiful foothills of northeast NC near the Virginia line. I just remembered the big clue that should be the key to finding the answer to one of my questions. If you will refer back up to photo #1, there is a metal arm or what looks like a guide for the cloth as it is rolled onto the cloth beam. Now which way should that be cupping the cloth? I'm think I have the correct position and the guide lays gently on top of the cloth beam as cloth encircles it?

Thanks for yet another great reference/resource Tommye. PS-I like your name!

2BobbieJ

It's northwest NC-I must be computer-logged from all of the extra exposure of late! Sorry.

 

Spinderella

I work for a textile and tool museum in South-East New Brunswick, Canada. This link is a great resource for setting up one of those 300 year old barn frame looms -- this one has a rising shed --  i am having difficulty at the moment with balance -- been working at it for 2 days now! Its just physics, I tell myself. I have two heddle horses on each side, suspending 4 top heddle sticks.

-the pulleys are centered from the stick suspending it on top of the frame

-horses are holding shafts 1 & 2, shafts 3 & 4 respectively on each side, with distance between suspension threads on each the same diameter as the heddle horses

-heddle sticks strings tie directly to treadles below, no lamms --- i have the strings all centered at the bottom of each heddle stick

When i tie the heddle sticks to the treadles, and press down on 1 & 3 or 2 & 4 i end up with the frames forming two opposing X's which give me "an opposite shed" -- a shed with no opening at all in the middle, and reversed shed on either side!

What do i need to do in order to fix this so i get an even shed all the way across?

thanks for any tips!

 

kerstinfroberg

An easily made mistake is to tie the horses "parallell" intead of "oppostie": if the right-hand end of the right-hand horse is tied to shaft 1, the the left-hand end of the left-hand horse should also be tied to shaft 1 - right-hand second horse end to shaft 3, left-hand too. Like this:

 As for "no lamms" - in Sweden we tie multiple shafts to one treadle anyway. In older literature it is said they used a ring made of cow's horn to keep all treadle ties centered. It works with any type of ring - even a "ring" of yarn works.

It is also possible to use an exrtra piece of dowel, tied under the shaft bar. This arrangement distributes the force, and helps minimize the sideways pull.

And... we can do "uneven sheds" too! Here is photo proof: http://weavolution.com/project/kerstinfroberg/counterbalance-loom-sheds

Spinderella

I will have to check to see how the horses are tied to the harnesses. I'm at home now, and our museum does not have internet access.

 

I have checked to make sure everything i have done in the set up is correct, however, i have yet to find such detailed instructions for the horse's attachement to the harnesses which you give here :)

kerstinfroberg

Yesterday I was at a small museum (Madesjö, Nybro, south Sweden).

Nobody knows exactly how old the loom is, and now it it used for weaving rag rugs in the museum. Two shafts are tied to one treadle, with help of what is also called "horses" (according to Grenander-Nyberg: Lanthemmens vävstolar). These horses are considerably bigger than the "upper" horses.

2BobbieJ

Oh my goodness, just look at this sweet thing-what a puzzle! Please check out the thing that I think holds the treadles-is that in the correct position? Do the treadles look correct? And the middle piece totally separates from the side pieces-is this the way it's supposed to be?

2BobbieJ

 

I believe the lower shaft (lower lamm ?) is in the correct position-otherwise, I would have to pull it back apart and flip the side piece up-side down to make the thing lower. Please assure me that it is correct.

2BobbieJ

And, as with other assembly projects-I have left-over pieces. Please help me identify them.

 

 

2BobbieJ

I think the beam on the left is the Pawl? But I do seem to be missing the supports that would mount it onto the loom? And what are the long sticks to the right? Or do these go with something else?

Maybe, they go with this extra thing propped against the old piano.It was stored in the packhouse with the loom? This has measuring sticks with little nails along the edges. I don't know what in the heck it is? It doesn't seem like a quilt frame? And it certainly doesn't seem to be part of the loom.

2BobbieJ

 

 

Is the metal piece in the top support piece supposed to fit squarely into the metal piece below? The loom had some warped pieces that required patience and coaxing to come together so the metal pieces do have contact, but only at the very end. Do I need to try to bring the warped sides in a bit more so the metal piece on top is centered on the metal piece below? And how does the beater stay inside the top bar. Do the bars pass through the holes and then a nail is driven through on the top side to hold it in place? I can see indentations on top where something held it in place, but there don't seem to be any nail holes at the top of the beater bar arms?

2BobbieJ

And what/how does something go inside the beater bar? Could it be the items at the upper right?





And one last question-the bar at the front of the loom has a smooth beveled edge which I placed facing towards the weaver-is this okay? Is there a reason why one side is beveled while the other side is not? Thanks everyone!

 

kerstinfroberg

is probably where the beater hangs. On my old loom I have one looking almost the same. Modern (Swedish) looms still use the same principle, but nowadays these, hm, cradles (direct translation; may be called something else in proper loom English) are made of wood.

I don't have a good picture of this exact thing at the moment, but I saw this on an old (1700-something) loom a month ago:

and a detail:

(There should be a cross-piece on top of the beater, too. I can't see it in your pics. Or - could that be the next pic - does the hole go all the way through? Would the beater uprights go through that hole?)

The "extra" beam could be the warp beam, and it could perhaps have been mounted with the help of some small extra pieces. My old loom had two separate brackets to hold the beam - can't find them at the moment (but haven't used them in almost 30 years...) They could perhaps go on the two pieces sticking out on your very first picture. (Or they could go in the two holes slightly higher up)

This is what cam be seen of them now, with the double back beam in place: (loom frame to the left; seen from inside the frame)

"Inside" the beater bar - do you mean the reed? The upper bar should slide - lift it to insert reed, push down to hold reed in place.

Keep us posted - and, most important: have fun!

2BobbieJ

The cross piece must be the "top support piece" with the metal pieces and yes!, it does have the proper slots to receive the beater uprights. I appreciate the photos, but I don't see what holds the beater bar in place on this loom. There are narrow linear indentations that run perpendicular on the top side of the cross piece. But when I look for peg holes on the beater uprights, I don't see anything except maybe a few small nail holes, but none of those seem to go all the way through. Do you think it would have been held by nails? Everything else is pegged so that doesn't seem right?
I am definitely missing the brackets. How common is that-to have all the pieces except these two? I guess it warrants a trip back to
that packhouse.
And those are reeds in the last picture-upper right-thank you for identifying the term. Just one reed at a time goes in the beater bar, right? I have several.
How old do you think this loom is? Thanks for all of your assistance.

 

Vamptoo (not verified)

Bobbie, I have one of those square frames with the measurements and nails all around it. My Grandmother told me it was a lace curtain stretcher. Basically after you wash your lace curtains you spread it out across the nails to dry. That way they would dry square. I inherited it with an old house that indeed did have lace curtains and lace tablecloths. Of course they were so old that when I attempted to wash them they disintegrated. I personally think it had a different purpose, possibly weaving. I will be curious to see what others think it is. Cindy

Amandablaine.

I just became the owner of a beautiful old barn loom in great condition and all working parts, but because I know nothing about weaving I am thinking of selling it. Can anyone give me any tips on where to start (ex. How much to ask for the loom or site to sell it on) any help would be greatly appreciated.
Submitted by Anonymous (not verified) on