Alison (not verified)

Actually, it's all pretty fun.  There is a certain freedom when space dyeing a warp, or spot dyeing silk hankies, and a certain sense of power from obtaining the control to get what you want.

Alison

Claudia Segal (not verified)

I am very interested in learning more about it.  Once you have inserted the pins in the cardboard, as above, do you then place them on a board?  Do you keep the graph paper underneath throughout the project?  

I tried a couple of things on my own and learned it's not as simple as it sounds.

Claudia

Ruth weaves (not verified)

Hi Claudia,

The draft (or graph paper in this case) stays under the weaving throughout. You lay the draft on the stack of cardboard (or whatever you are using for the pin board) and the strip of folded cardboard in position on top of that and put the pins in to hold it all together.

I hope that makes sense. :)

Ruth

naturalfibres (not verified)

Ruth, your jacket project is very fascinating - what an interesting idea.

Anne

kbird (not verified)

Ruth -

Should I assume that a small hammer might make the job of pin placement much, much easier?

And, are those "push pins" that you are using as compared to sewing pins perhaps?

I love the idea of trying this method of weaving, and I think your innovation is terrific.

Thanks for Sharing...
Kay

Ruth weaves (not verified)

The pins I'm using are ordinary dressmaker pins with round heads. They need to be fairly long and pushed in at an angle (like a tent peg). I don't think push pins would anchor the warp well enough in the cardboard I'm using which is fairly light weight (e.g. ikea boxes). I make a stack about 6 or 8 thick. I push the pins in by hand and they go in quite easily. If I'm doing a lot I use a thimble to save my fingers. Maybe if you had a firmer surface like cork, push pins would work and then you might need a hammer. The beauty of using cardboard is that it is so quick and cheap.

Hope that helps!

Ruth

 

 

 

 

suzyhok (not verified)

Hi Ruth...

I look forward to seeing the progress of this ambitious project. It's going to be beautiful!

I haven't used Pin Weaving, but I have noticed when I do my cardboard loom weaving that after the first 1/2 inch or so I am able to weave much more easily because the web that has been woven lifts the warp threads off the surface of the cardboard.  Your idea of a spacer on your pins to get started is brilliant!

I can't wait to see the finished piece!

... Suzy

Claudia Segal (not verified)

The difference in using 8/2 vs 10/2 will be mostly in the sett.  If the pattern is a plain weave then with 8/2 your epi (ends per inch) your sett will be somewhere between 15 and 22 and in twill 22-30 depending on the project.  If you were using 10/2 cotton, as the pattern says, you would have a sett of  18-25 for plain weave and 25-36 for twill.

Shrinkage and take-up should be about the same.  You need to sample, sample, sample.  

Based on what you have written, it sounds as though you are threading 25 pairs of A and B.  So if A is white and B is black you will have one white and one black 25 times for a total of 50 ends.  Keep in mind, however, that with a wider diameter yarn, you will either need fewer ends or you will have a wider project.  

I hope this helps.  If you can provide more information, we can offer more assistance.  Number one is always to sample, especially when you are making changes.  You are striving for the same pattern in a different yarn, I would start with the same dimensions and see what you get in shrinkage with your sample.

Claudia

illoominated (not verified)

Thanks for answering my questions. I can do this! However, there must be a trick to warping when you alternate the color every other thread.  I've done blocks of color, 20 black and then 20 white on the warping board so that I have one large chain when I pull it off. Any resources/tricks for how to warp the AB pattern? Do I sley 20 black, skipping a slot, and then sleying 20 white in the slots I skipped?  I'm not so great at warping yet, it's hard for me to imagine what will happen when I start winding the warp to the back of the beam when I have so many little chains at the front.

Claudia Segal (not verified)

If you are winding a warp of alternating color such as the one you are working on now, you tie the two colors together at the beginning.  Then, while keeping them separated with your index finger to prevent tangling, you wind your warp.  This gives you alternating threads, A and B.  Sorry I don't have a photo, it would be easier if I could show you.  

Does that make sense?

Claudia