I have a quick question about warping with silk.

This is my first time working with silk as a warp (having previously worked extensively with cotton and tencel warps) and I really struggled with my silk shedding and joining together during the threading process.

I am working with a combination of 30/2 and 20/2 silk at a 40epi (I am using a 20 end reed, threading 2 per dent). I hand dyed the silk and warped back to front off of lease sticks. During the threading process the individual warp threads joined (it looks like the threads were pilling and joining with the neighboring threads- sometimes upwards of 5 threads would join together). Often the threads could not be simply pulled apart and in fact needed to be cut loose from shedding fibers joining them. I managed to get the warp on the loom and have started weaving but I've found that the silk threads continue to shed and form these lint balls on the individual threads. I'm worried about this affecting the strength of the silk fibers and causing knots and breakage or being further abraded by the wire heddles/metal reed

I have read on these forums about potentially sizing the silk and addings starch- would that help avoid this situation from occuring in the future? Or could this be a result of my dye process affecting the fibers? I used a MX fiber reactive dye with soda ash as an activator.

If anyone has some suggestions for avoiding this tangling issue in the future I'd very much appreciate it! Thanks so much for all your help!

Comments

Catweaver

I find the soda ash makes the silk harder to handle and damages the fibre. When I dye silk or wool with Procion, I leave out the soda ash completely and use Resist salt L which acts as a fixative because it is mildly alkali. You an also use sodium bicarbonate but I have never tried this. I also steam the silk after dyeing which i think helps to fix it as well. Another option is to use an acid dye eg. Lanaset, which uses an acid - vinegar or citric acid - as a fixative.

Catweaver

Forgot to say - have you tried this website? Lots of info about all aspects of dyeing. http://www.pburch.net 

Sorry this isn't very helpful for the warp you are struggling with now - but hope it will be helpful in the future.

tien (not verified)

I'm pretty sure it isn't the MX with soda ash dyeing process that is causing you problems, because that's how I dye most of my silk yarns (even the really fine ones, like 120/2 silk) and have had no problems. Instead, I suspect you've just got a loosely-spun silk or a silk yarn with short fibers that is pilling on you. I've had a few yarns like that and they are just a royal PITA. I'd try sizing the warp - I think a single packet of gelatin in two cups of water is the recipe, but look online for confirmation. Also, in the future, use that yarn only as weft!

Catweaver

That's interesting to hear, Tien. I have only used soda ash when I dyed 20/2 silk a few years ago, and had bad results, so since then I have used different methods. It may well be that the yarn I used that had problems was loosely-spun: I don't know enough about spinning to know. I still use the same yarn (there's not a great selection available here) and have just examined it more closely - but I still don't know enough to say!

sbaskin

Thanks so much for all your helpful comments! I'll look into different dye processes and sizing options for my silk!

Thanks again

Sara von Tresckow

Sounds as though you are threading prior to winding on. Any threads that might tangle profit from being wound onto the warp beam, through a set of lease sticks prior to threading. That way, each individual thread should be in order in the cross and relatively easy to sort out.

If you went first through a reed and then try to sort out these sticky threads to place into h eddles without any tension or lease sticks, you'll have a problem with the silk no matter how it is dyed.

sandra.eberhar…

Where did you get the silk?  I recently got some single-ply, fairly softly spun silk on Ebay from a supplier in Oregon.  It's Indian in origin.  It made good weft, but would have been a nightmare as warp.  It's quite strong, but not abrasion resistant.

sbaskin

the 30/2 silk I picked up from The Mannings in PA and online from Halcyon. The 20/2 silk I got online from Webs
I've been having much less trouble with the 20/2 from Webs- the 30/2 has been much more problematic.

 


In response to Sara's suggestions- I used lease sticks when warping back to front. The knotting seems to be occuring mostly at the lease sticks themselves. The yarn is pilling and joining with neighboring yarns together at the cross in between the lease sticks.

 

Do you think going through the front of the loom could help? If I held the cross in my hand maybe the strands would be less likely to pill against the wood of the lease sticks and join with the neighboring yarns? It feels wrong to go through the front to avoid tangling but the lease sticks seem to be the source of my silk woes.

again thank you everyone for all of your help! This is my first time posting and everyone has been so supportive- I'm learning so much about working with this material. thank you thank you.

Dawn McCarthy

It may be a softer twist - whenever I have had this experience (usually with certain wools) I will make both a porrey and portee cross, I use the portee cross to sort threads into the raddle and then wind on without the lease sticks (it is very rare for me to go without lease sticks but I found in this instance it helps), wind on until you get to the second cross (porrey), replace the lease sticks in once beamed on to assist with threading etc and once you are ready to weave, remove the sticks as the flat sticks sometimes offer too much drag causing certain fibers to pill or cuff together will.  Sometimes I will switch out a flat lease stick for a round dowel and that seems to help)  if not I work without the lease sticks once the loom is ready to weave.  One always has the option of replacing the lease sticks at any time.  I really dislike getting rid of the lease sticks but I have had certain wool warps cuff, once the sticks were removed the problem was greatly reduced.  Odd that this is happening with 30/2 silk.

Dawn

Bewove

Sara von Tresckow

I usually use 2 threads in the cross and pay careful attention to those pills if they form - removing them as soon as they form. If you then separate them with your fingers, they behave for a fair distance. Cotton and wool and mohair, etc. can also act that way. I have found that placing the raddle ahead of the lease sticks sort of presorts the threads before passing through the lease sticks and avoids those stickers.

Going slowly and gently while paying attention is probably going to as much to improve the process as anything else.

Submitted by sbaskin on