okay, I am a new weaver so please bear with me on this silly question. I am using a new to me Harrisville 4S/4T floor loom and my warp threads are about 1/2 inche above the bottom of the reed so when I throw the shuttle, it falls between the warp threads and I have to reverse it. Is this a technique problem or should my warp threads be at the bottom of the reed so the shuttle can ride on the reed edge? Hope this makes sense. My warp threads are already riding at the top of the heddle eyes so I can't lower the shafts anymore. Any suggestions? Thanks in advance for your help. Oh and the beater bar is not adjustable as near as I can tell. 

Comments

Joanne Hall

On a jack loom, the threads are always on the tops of the eyes of the heddles.  But your loom has hanging shafts and you can lower the shafts so that the warp threads will lie on the bottom of the reed and on the shuttle race.  The race is put on jack looms to help keep the shuttle from falling.

Joanne

sally orgren

Just checking. (Jack looms are designed to operate with shaft weight, and sometimes when folks replace the metal heddles with texsolv, I have heard it can effect the performace of the loom.) 

What is your sett?

How wide is your warp?

What kind of shuttle are you using?

How do you hold your shuttle?

Jane Greer

sett is 10, warp is 18 inchs, boat shuttle, metal heddles. hold shuttle with thumb and index finger and first finger to shoot it through.

i don't have enough cable left on one of the shafts to lower it anymore. And if I lower it more won't that cause strain on the warp threads?

 

 

sally orgren

Jane, those all sound good. 

Are you truly shooting the shuttle through the shed (parallel to the floor) or is there a slight downward direction (or flick at the end of) your throw?

Does the shuttle dive down in about the same place every time?

Does it dive down when thrown by the same hand (and not as often by the other hand?)

Another thing that might help — posting a side view photo of the open shed (with the beater resting against the castle). 

How frustrating. I hope collectively we can help you figure it out!

SallyE (not verified)

It's common on jack looms for the shaft to pull the warp threads down a bit.  When you think about how much those threads get pulled when the shafts are pulled up to create a shed, pulling them down a little bit is not a problem.   As for the too short chord, you might have to either replace it or add a piece of chord.   It might be that someone along the way replaced it and used a piece that was a little bit short.

On my jack looms, the warp is always pulled down a bit when going from the back beam to the breast beam.

 

Jane Greer

Thanks so much for all the help!!! I am shooting it the same way and its at different points it falls through the threads. When I look at videos of other weavers it always looks like the warp threads are laying at the bottom of the beater bar and mine don't, so it would seem that is the problem. Because of that I can't shoot it along the race (guess thats what that is called...lol) and so there is no support to keep it from falling through. Does that sound about right? Sorry, no weavers in my area to take lessons from so I am having to teach myself from online information. 

Thanks again for your help, you guys are great!!!

 

sally orgren

Is your warp something like carpet warp or 3/2 cotton, or is it a beefy thick yarn?

Is your warp taut? Did you try cranking up the tension a bit?

If your sett is 10, that means with the shed open, you are throwing the shuttle over just 5 ends per inch with plain weave. So yes, there is high potential for the "ouch" factor when the shuttle hits your foot because this is a very open sett (more like a rug sett), particularly if you are using carpet warp, 3/2 or 5/2 pearl cotton.

The type of weft used at this sett with carpet warp or similar would likely be 1" rags or very thick yarn. In that case, most folks would use a long rag shuttle (probably not a boat shuttle) because it holds way more weft. Those shuttles are also much longer than a boat shuttle, so they can be passed through the shed instead of thrown. ("Ski" shuttles are another kind of rug shuttle that can be thrown.)

Having a tightly tensioned warp makes the lower warp surface smooth for the shuttle at that open of a sett. If you already have a narrow shed, sometimes folks are reluctant to tighten the warp, but it can make a world of difference.

What kind of boat shuttle?

I have some low profile shuttles for my narrow shed looms. Also, a longer boat shuttle might help with this warp rather than a shorter one because the sett is so open. And a slightly more blunt-nosed shuttle may help the shuttle find the sweet spot in a narrow shed than a pointy one.

Okay, good luck. Those are the variables I can think of for now. Believe me, I have smacked my feet many times when I wove a series of Krokbragd rugs with an open sett like that. 

Jane Greer

It is a worsted weight yarn so it's pretty beefy but I will try a longer shuttle. I have woven about an inch of header and the tension is right, I don't have any hills or valleys. 

mrdubyah (not verified)

Maybe your problem isn't heddle height, but reed height. Check your beater to see if there might be a high and low position for mounting it (look for a second hole or slot for the pivot bolt.) Some bottom mounted beaters have more than one mounting position.  Yours may simply be in the lower of two mounting positions. 

Jane Greer

I put some chain on the end of my shaft treads so I could lower them and now the warp threads are laying on the bottom of the reed like they should. It is a pretty narrow shed though but at least now I can use the race to run the shuttle on. Now if I can just fix all the threading issues....lol. I just realized that right in the middle of the piece I missed a heddle so now I have to rethread the other half.....maybe someday I will actually get to weave....lol

 

Jane Greer

I checked for that first thing, not adjustable

 

laurafry

While your tension may be even is it sufficient to support the shuttle? Many looms don't have a shuttle race, the shuttle just travels on the floor of the shed. Cheers Laura

sequel (not verified)

If your warp tension is too high on this loom, the lower shed will rise up off the shuttle race.  If the tension is too low, the shuttle may not be adequately  supported. 

If you are using the plastic shuttles from LeClerc, well, that could be your trouble right there.  The tips of these shuttles are a little low and tend to nose dive under the warp regardless of warp tension.

The correct height of the shaft frames is 8 1/2” from the TOP of the castle.  Adjust your treadle ropes to achieve this.  This loom did not come with height adjusting chains like the 6 treadle variations did.

Submitted by Jane Greer on