Hello,

 

After many years of resisting weaving, I have finally caved.  I recently finished restoring a Gilmore 8h/12t 54" and love it.   However, I’m now looking to add  a second loom.  I'd like something for smaller projects.  Lower warp waste is a priority as I hope to primarily use handspun. 

 

I had been leaning toward a Julia 4h/6t CB based upon price/footprint and a desire to have either a CB or CM loom.  Then, during my research I came across the Toika Laila.  The pricepoint is similar to the Julia CM configurations and the folding capability would be nice bonus.  Unfortunately, I haven’t found the pro/con reviews like with the Julia. 

 

Has anyone handled both enough to provide a comparison?   Does anyone have a general idea on the loom waste for the Laila?  Is there a strong advantage to an overhead beater at this size?

 

Thank you in Advance,

 

Dawn in Atlanta.

Comments

celtinbirks

Hi

I can't answer all your questions about the Laila vs. Julia, but if price is an issue, you can probably find a used comparable CB loom locally for a LOT less money.  I believe that the Laila is a little bit heavier duty than the Julia.

Blessings!

Candy

SallyE (not verified)

In my experience, loom waste isn't too much different one loom from another.   To reduce waste on all my looms I make sure that the chords holding the warp and cloth rods (or the apron in the front) are long enough to let the rods reach all the way to the first shaft.  Once I do that, the waste is more a matter of the knots in the warp that hold it to the cloth rod.   To reduce waste in the back, I warp back to front and I don't cut the warp lengths in the back.   I just slip the rod through the loops so I waste very little to tie on.

Finally, because you have to divide the warp between the sections of the chord running from the metal rod to the warp beam, I made each chord (from the warp beam to the rod) it's own piece and attach it to the rod with an "S" hook.   That way I put the entire warp on the rod at once with just a hook at the far left and far right, spread out the warp as needed, and attach the middle "S" hooks to the rod as needed.   Much easier and faster.

For all my looms from my table looms to my floor looms, the waste is about 25 or 27 inches.

 

Dawn McCarthy

I have 2 Laila's for teaching/sampling.  I cannot compare with the Julia though.  The loom is fairly solid, easy to set up and use, low profile and folds (that is a big plus) the treadles are decent and the front and back breast beams can be removed.  Simple ratchet tension (good tension) not sure if heavy enough or wide enough for a rug but good for most everything else.  I have been very happy with the Toika loom, the underslung beater is not a problem, the loom appears to take up a small amount of space as it is much lower than the Julia.  Glimakra also makes a great product, I suppose the biggest difference is the appearance of space and actual footprint of folding vs non-folding.  The other plus for the Laila is the peg construction making it very easy to take apart, it could be used as a workshop loom although it weighs about 60lbs and might take two people to load in a car.

I have some pics on my blog

http://bloominloom-dawnmccarthy.blogspot.com/2011/07/toika-laila.html

 

tatmia (not verified)

Thank you for the replies.

Dawn - your blog was one of the reasons I started looking at the Tokia, so thank you.

My Gilmore was purchased locally for a very good price (even factoring in the price of replacement parts).   I will continue to watch for other looms.  The only CB/CM's that have come up over the last year have been large or homemade which is why I'm considering purchasing new. 

Submitted by Anonymous (not verified) on