I had posted this in the RH group, but Claudia suggested that I also post it here, for more visibility. :) 

I have a question about heddle size. My Kromski Harp RH came with a 10 dent heddle, so until I purchase the 8 and 12, I am using the 10. I am currently working on a table runner with 3/2 mercerized cotton, all the same color, with this 10 dent heddle, and I am trying to figure something out. I understand that this is not a “balanced weave”, because although I have used the 10 dent, the weft rows are measuring 8 per inch. I like the open looking weave, and it’s fine (warp dominant, right?), but I am confused about which heddle would have made a balanced weave. Since I am getting 8 picks per inch, an 8 dent heddle would make sense, but my limited knowledge thus far would have guessed 12, instead, because this yarn is actually much lighter than I have been using for scarves. On the other hand, I could never pack this yarn tightly enough to get 12 picks per inch (I don’t think?). Is this because the 3/2 cotton is not as soft…more tightly wound? At any rate, my “guess” of 12 is the opposite of what I am seeing happen, which makes me think 8, for balanced weave……can anyone enlighten me? Thanks. :)

Comments

debmcclintock

Have you measured it after you wet finish a sample?  The 8 PPI in the web might magically become 10 PPI in the finished cloth and become a balanced weave.

laurafry

3/2 Perle cotton is quite dense and stiff.  It looks like you are getting a good consistent beat, and ultimately that is going to produce a nice looking cloth.  I wouldn't call this warp emphasis - the warp would have to be much more predominant than your cloth looks.

If you were weaving on a floor loom instead of a rigid heddle loom you could beat harder and get a higher ppi.  But so far I think your cloth looks pretty good.  When you wet finish it, I'd suggest a good hard press or cold mangle to flatten the threads and notch them down warp into weft for great stability.

cheers,

Laura

check my You Tube channel for a cold mangling video clip

lkautio (not verified)

Average the warp and weft numbers to get the sett for a balanced weave with the same degree of openess/firmness.  That means a sett of 9 here (10+8)/2.  On a floor loom I sett 3/2 at 10-14 epi for a balanced weave in plain weave depending on the effect I want.  10 is quite open already, and with 8 ppi is even more so.  It's fine as long as the finished piece is stable for the intended use.

Laurie Autio

clgy (not verified)

Ahhhhhh......Okay. I have one of the two I made in the dryer right now. You have no idea (or maybe you do!) how hard it was to throw my newly woven runner into the washing machine! I used delicate cycle, cold water, and I am going to remove it from the dryer while still damp, then press. Then, I'll count and see if maybe it is indeed now 10ppi. I am trying to keep good notes about the results on and off the loom and after finishing. Thanks for reminding me to measure after it's "finished".      

clgy (not verified)

Laura,

I had never heard of cold mangling --- thanks! I will enjoy your other youtube videos too. I really liked seeing the fringe twister as well, since I had been wondering about it. As for my runner, I was amazed at how consistently I was getting 8 picks per inch, since with other yarns it was varying a bit. So I'm not unhappy with the result at all - I like the open weave - but I was just confused about whether 8dpi or 12dpi would have been better for a balanced weave. I am hoping to do more sampling later when I get my other heddles. Thanks!

clgy (not verified)

So if I had used 9 ends per inch for the warp, by skipping one hole and slot, I likely would have had 9 picks per inch also? 

Claudia Segal (not verified)

If you skip one hole and one slot on a 10 dent heddle, you will have 8 ends/inch.  The heddle is set up for 10 ends/inch which includes both holes and slots.  SKipping just one give you 9.

For finishing cotton items, I use warm-hot water and then in the dryer until they are damp dry.  I then give them a hard press on both sides with a steam iron and I usually do the first side a second time. 

Looking forward to seeing the final table runner in your projects.

Congrats on your project.  Each new fiber, each new project is a new learning opportunity.

Claudia

kerstinfroberg

An article on "serious" mangling - here. (Ok, I wrote it myself, but the mangle in question *is* serious...)

Continuing to toot my own horn (I make fringe twisters, too), here is how to use one.

Have fun weaving!

Sara von Tresckow

On a rigid heddle loom, the "rigid" part is the sett of your weave. Unlike a loom with interchangeable reeds and free moving heddles, you cannot vary your sett as easily.

That said:

1. Fabric, since antiquity, has been slightly warp "dominant". That gives it grain and drape. Not to mention, when using something like a warp weighted loom where you push up the weft slowly, having most of the threads already in the warp is a good idea. There are many fabrics that are not "balanced", yet are quite successful.

2. As you are finding out, washing will bring your threads together a bit and hard pressing/cold mangling will help fill the holes in your intersections.

3. 3/2 cotton is pretty horrid stuff to weavers who make fine cloth. It is stiff, dries slowly, ravels easily and just doesn't drape at all. If you try with double strands of 5/2 you might like the fabric better. Using one thick, stiff thread makes things go faster, but the fabric produced is not always what you'd like to touch or use. Ashford uses double stranded 8/2 and a 12 dent reed for their towel pattern on the RH loom.

4. If you wish to have better weft packing with a rigid heddle loom, don't just use the heddle to "beat". When you have the next open shed, use the side of your shuttle (works best with a beveled or cotton shuttle) and press it into the shed until your weft is where you'd like to have it. This step is necessary for weft dominant or weft faced weaves on the RH loom.

5. We usually put a 3/2 potholder warp on our table loom for summer shows - we get a firm tabby at 12 epi.

Submitted by Anonymous (not verified) on