Somewhere I read something about how helpful it is to weave a sample before starting a project.  I can't remember, but I believe they had some specific small "looms" to weave these samples on.  Does anyone have any ideas on this?  I don't know where to look for these.  I am just new into weaving but very interested.  Thank you.

 

Comments

Sara von Tresckow

Any small loom with good tension wil weave a sample.

Important to remember is that if you make your sample quite narrow, the full sized cloth will pack in less firmly, so your sample will only be approximate.

You can also try a small sample on the large loom.

kerstinfroberg

It can also be a good idea to make a longer warp and use the last part to sample for new projects/ideas. For instance, use several "unlikely" colours (some may come out a lot better that you'd have thought), and/or different treadlings and... just 10 cm of each will give and idea of the result.

Claudia Segal (not verified)

It may be useful to include extra warp for sampling when you calculate the length of warp you need for a specific project.  It can lead to surprises but there are times it works out.  I do this and sometimes try different color yarns for weft and I cut the sample off the loom and wet finish before I continue with my project.  

Claudia

sally orgren

Sampling is an excellent habit to develop as a new weaver! 

I have several small looms I like to sample on. Available to me currently are the following: Structo 240, Structo 600, LeClerc Dorothy & Voyager, and a rigid heddle. But there are MANY other "table looms" equally suitable for creating small samples.

Participating in "round robins" at a guild program or conference workshop is one way for you to decide what kind of sample loom will be right for you — you'll get to sample the sample looms ;-)

But often the first and simplest place I start is by making a little needle weaving. I wind my planned warp around a 2" piece of cardboard. Then, with a tapestry needle, I weave bits of potential weft in to see the effect. I don't spend a lot of time at this, just enough to give me a little better idea in my mind of where I want to go next. 

Sally

lkautio (not verified)

I sample extensively, but always on the loom I am going to weave the project on.  I have never owned a sample loom, and in 25 years, never felt a need for one.  My three floor looms do the job perfectly well. 

I also usually make my samples full width (usually at the start and end of a warp).  If you make narrow samples, they are easier to beat in.  If you want the same number of picks per inch in a much wider piece you must generally beat quite a bit harder.  This is not a problem if you work with a ruler and beat to a number of picks per inch.  It is a problem if you beat solely by feel - it won't feel the same.  It also may require extra weight on the beater to help you with the force needed.

Laurie Autio

sally orgren

Okay. I admit, I am a sample-a-holic. Guildmates think I am crazy sometimes, but I really think sampling helps you get to a place with your weaving that you might never find otherwise. It's like the old saying, "You don't know what you don't know." 

My process is typically to prepare some form of a small warp-wrap/needle weave (rough idea of color and sett). Then, many times I'll jump to a small sample on a table loom. Usually it's a 1-2 yard warp, (using a loom with minimum loom waste). The purpose is to refine my idea. I have even been known to set up three different warp options, and recently tried a sample with three different setts across the single warp.

In many cases, at this stage I may not be quite ready to take my idea into a multi-yard warp committed to the big loom. Sometimes there are material limitations too. My floor loom takes 24" for loom waste. 24" x 45" (max width) X 15 epi = 450 yards. The Structo 240 = 10" (loom waste), 8" (max width) X 15 epi - 33.33 yards. A LeClerc Dorothy/Voyager 15" X 15" X 15 epi = 93.75 yards. (You get the idea.) Which loom I sample on may have to do with trying to use as little material as possible, saving most for the project itself. And sometimes I end up weaving the whole project on the table loom if the material is really precious, like handspun angora!

As the last step, I always allow some "what if" warp on the big/real loom I plan to weave the project on. And don't save it for playing with after you finish your project. Many times in playing with the last little bit of warp, I would discover options that I actually liked better than what I had just woven!

Some people think sampling is a waste of time, but many of the weavers I most admire tend to be samplers, too. Added benefits; the more you sample, the quicker you add to your skill base, the faster you become at all aspects of the warping process, and you have left yourself little crumbs along the weaving trail so you won't go down as many non-productive paths in the future!

Sally

Cally (not verified)

Like Sally, I am addicted to sampling - it is great for the low-boredom-threshhold weaver ;-)

When you are new to a particular structure or fibre then I think it makes sense to dedicate a sample warp to exploring it before you commit to a project. Working with it may turn out quite differently from how you imagined before you started - and although it may be even better than you had anticipated, it may also turn out to be impractical for the purpose you had in mind.

However, if you are using familiar yarns and structures then I would just add a small amount to your main warp, say 12" (though I can easily experiment for a yard or so!), and try out some possible wefts before you commit yourself. Then cut off the sample and wet finish it before you proceed; seeing the finished cloth may lead you to a different choice from the one you preferred on the loom.

In neither case do you need a dedicated sample loom unless you want one. I have an eight-shaft table loom which I sometimes use for sampling, but more often than not I now weave my samples on the floor loom. I find it quicker and more comfortable, and I don't mind that it isn't portable as I'd rather be in the loom room than anywhere else!

Good luck with your weaving

Cally

tede56

Good to know - obviously I would have never known that.  I have so much to learn!   Thanks so much!

tede56

Good to know - obviously I would have never known that.  I have so much to learn!   Thanks so much!

Eva (not verified)

In the 1980's I freelanced as a sample weaver for textile companies.  A designer would hand us a layout with a draft and a bag of yarn on cones.  We would take it home or to our studio and bring back a woven sample about 8" x 10."  Most of these samples required 4-16 shafts and had a sett of 28-40 e.p.i.  These samples helped determine which textiles would be mass produced by these companies at their mills.  One company I sampled for, I think it was J.P. Stevens,  had its own "weaving room" in their NY office with a few Macomber looms, for weavers who wove samples as a full-time job.

We all agree that weaving samples really helps to figure out what will work best for a finished piece.  Sometimes I weave samples just because I love to weave samples, experimenting with different weave structures and color combinations.  I often post drafts and notes with photos of the samples on my blog.

I prefer using my floor loom for weaving samples but I have used a table loom too when I needed to try something while my floor loom still had weaving to be finished on it.

Eva Stossel

 

Submitted by tede56 on