There is a discussion of sett that ended up in the backstrap forum and I am trying to move it to this forum.  We'll se if this works or not.

Claudia

Comments

Caroline (not verified)

hi Claudia, Good idea to do a refresher on it for those who haven't come across the term, or needed to use it!

Without getting technical, the sett is basically the number of threads per inch of the warp and weft once interlaced. Too few threads, and the fabric is sleazy and may not hold together, too many and its stiff, and hard, and unwearable.

To get the right balance you first need to know how many Wraps Per Inch (wpi) your yarn has, which can be worked out by wrapping it around a ruler, not too close or tight, but just so each strand is touching its neighbour. This will tell you  how many strands of yarn you will need in your warp and weft together for what is called a balanced fabric using this particular yarn - where each strand of yarn takes up equal space.

Half of the WPI will give you your Ends Per Inch for a balanced plain weave, so for a yarn that wraps around 60 times, you will get 30 EPI on a well balanced plain weave. This gets adjusted according to whether you are doing a twill fabric, where the warps may be closer together , or you are doing a lace weave, where the threads will perhaps be a little further apart.

This is where Sett comes in. If you are following a project from a book or magazine, there will be a recommended sett. This tells you how close the warps need to be threaded to make the fabric.  If you have the right sized yarn, the sett will be about the same as your EPI, more for a twill. However if the sett and the EPI are nowhere close, you need to either find a different yarn that will give you the right sett, or else adjust the pattern.

Many smaller looms and books about smaller looms don't worry about sett - if you have a 7.5 size rigid heddle on your loom, they recommend using an 8 ply or worsted yarn - this gives the right sett when you warp the loom up to 7.5 threads per inch through the heddle. If you used a sports or baby weight yarn, it would be far too thin, and bulky would not even go through the slots and holes on the heddle. You would not do too much better trying to warp an inkle loom with bulky yarn for a dog lead - it would not work!

So sett is important, regardless of loom, and if you are trying to make a nice length of fabric, its what makes the difference between something that is near enough, and something that is good! Its worth getting hold of a weaving book and reading up about.

If anyone has anything to add to this, please go ahead!

Cindy Jo (not verified)

Thank you for the info.

Cindy Jo

lkautio (not verified)

The same yarn in the same structure will have a range of setts depending on the final product and the hand desired.  For example, 40/2 linen may be sett for plain weave or laces at 24-40 epi with very different results.  The 24 will be right at the border of sleaziness, but good for open, airy curtains. It would also make a good base for inlay or brocading, or perhaps some other finger-manipulated weaves. The 40 will be tougher to beat square, but make hard wearing materials for upholstery, etc.  At 30, you might have a good table runner, and at 32-36 napkins or crisp clothing fabric. 

The size of the block in a block weave will affect the sett.  A block with smaller floats (like a lace with 3-thread floats) may be sett a little more open and still be stable, than a larger block with longer floats in the same structure. 

While it is most common to try for a balanced weave with ppi =epi, you may design unbalanced weaves.  This is one of the ways around the limitations of owning a single rigid heddle, but is a useful trick on any loom.  If the pattern does not square, try a finer or heavier weft if you can't change the sett.  Or design non-square pieces.  Weft-faced pieces with wide setts and warp faced pieces with setts that are very close (twice plain weave, for example) for the yarn used (and everything in between) are useful to understand.

Sett also depends on the slipperiness of the yarn.  A slick reeled silk or shiny rayon will need to be sett tighter than a spun silk, smooth cotton, or silk noil of the same diameter to be stable.  Woolen and worsted wools will take somewhat different setts as will tow and line linen, mercerized and unmercerized cottons, etc.

Reflectivity may also influence your choice of sett.  A very reflective yarn will show up a pattern more easily at tight setts than a dull yarn, which needs to be sett a little looser to be as visible.  Color can have similar effects - try opening the sett of very dark yarns a little compared to very light colored yarns to make the pattern more visible.

You can try other tricks with sett, for example, comparing the difference between a single thick yarn, a doubled finer yarn that is half its weight, and the finer yarn through separate heddles.  Variations like this can change the hand and appearance of the material dramatically.

Laurie Autio

Submitted by Anonymous (not verified) on