Is there a handy formula for figuring out knots per inch?  I'm sure there is something extremely obvious that I'm missing.  I was reading this article  www.rugreview.com/orr/82chris.htm which states that the rug in the article is 30 to 40 knots per inch as the author estimates it.  I'd like to take a bit of the design and warp it up as a project but am unsure how to figure this part out.  Thanks, Virag

Comments

Sara von Tresckow

 Multiply the number of knots in a row that equal an inch by the number of knotted rows that make up an inch and you have your value.

8 knots per inch on 8 rows per inch - 64 knots per inch.

Caroline (not verified)

hi, if you take the size of the carpet as he says, approximately 28 inches per side and nearly square, then the 5 motifs on each side would be just under 6 inches.

If you have a graphics program with a grid, you should be able to insert the photo and get down to how much of the photo an inch actually takes up, and work on from there.

Otherwise make a scale drawing - even if its only a cartoon. I like to do this on graph paper, but you could also enlarge the photos and print it off on graph paper, and you can use this same paper to work out what is needed for the bit you want to do.

I still prefer the hands on paper bit, but thats because I have never quite got my head around a graphics program.

Hope this helps

Virag (not verified)

Awesome, thank you!  I get so frustrated with this part.:>>

Virag (not verified)

It really does help, thank you Caroline.  I am going to go pull out some paper and pencil to start with.  I am terrible at math but I need to conquer that and move on.  I have two tapestry looms crying out to be used!

Virag (not verified)

Just to make sure I get this...

 

If I want to come up with 36 knots per inch I would take 12 wpi and multiple by 28 then divide by 5.  Round the answer down to 335 and divide by 5 to get 67 warp threads for 1 motif ext. at about 6 inches wide?

Sara von Tresckow

Uh, you estimate the knots per inch in a row - if you are knotting around 2 warps, and have 15 ends per inch, you have 7.5 knots per inch in the row.

Now, as you weave, you count the rows of knots that make up an inch - maybe 6 rows

NOW multiply 7.5 times 6. The density of your piece is 45 knots per inch (square inch). 

What those numbers of yours mean is totally unclear.  You really can only estimate your knot number until you begin weaving and measure on the loom. How firmly you beat and the thickess of your pile weft will influence your knot count. Sometimes motifs must be adjusted to give an attractive appearance - either stretched or smooshed - this is NOT rocket science.

Virag (not verified)

Aha, I get it!  Thank you for your patience and help.  :>:>:>

lambspin (not verified)

The usual answer: sample :).

Ideally, you want the design to square, that is four knots x four rows would be a small square, not elongated or truncated. To achieve this, you can vary the number of knots per inch, the size of the pile yarn, or the number of shots of plain weave in between.  Also ideally: the better rugs have fewer shots between rows, making a firmer textile. You can also just change yarns: a very fine warp will allow for the knots to beat down tighter, but may require a closer sett, etc., etc., etc. 

Marla Mallett's book Woven Structures has some lovely examples of rugs showing the backs, so you can see how the weaver created the textile. 

I did a blog post on a recent piece here:  

http://saralamb.blogspot.com/2010/01/stranded.html

 

Submitted by Anonymous (not verified) on