I'm new to inkle weaving - as in this is only day three or four! (grin).

My first project (here, and here) worked like a charm - I was REALLY pleased with the result not knowing what to expect or the possible pitfalls. Now I'm moving on to experiment with other pattern making techniques and I've hit a snag on the first run. Helene Bresler's book describes a weft float technique "brocade" and I thought I'd try that.

I warped up - and carefully followed here directions. Nope. Not happening.

Un-wove it - tried again. Also nope.

Went online to find others doing the same to "see" what I was missing - nope - no luck there either.

So what's going wrong?

Bresler describes how the "binder" weft goes through the shed at the same time as the "pattern" weft. The brocade pattern is on one side only. When I do it - the pattern is so broken and non-existent that I'm sure I've done something wrong. The warp & weft threads by the way are the same size so that should not be the problem - the pattern thread is a bit "fluffier" as she shuggests though.

Has anyone else tried this technique? Does anyone know of a video or picture tutorial of this being demonstrated?

Many thanks.

Comments

bolivian warmi

Hi Alexis,

I do brocading (or weft inlay or supplementary weft patterning) on pieces on my backstrap and I imagine it is exactly the same. Firstly, Michael Cook did an article on WeaveZine about brocading with card weaving and I imagine that the way to lay in the supplemenatry weft is the same. He has videos in the article too so that might help.

Here is some brocading on a little bag I made recently-sneak preview just for you! I haven't put it on my Project Page yet.

My brocading weft is 6 strands of a very fine cotton-they lie flat and wide so they show up well against the plain weave. Basically in your open shed you just lift the warps under which you want your brocading weft to pass and drop the ones over which you want it to pass. Then pass the brocading weft. Then you pass the main weft through the complete shed-you can pass the main weft before or after the brocading weft-it doesn't really matter-just try to be consistent.

The important thing is to have the right warp to brocading weft ratio and you may have to experiment to get this right. If the yarn you have chosen as your brocading weft is not thick enough, it just won't show up and there will be big gaps between rows.

PS.......did you see my latest blog post? I announce there that I am going to do a photo tutorial on just this topic soon!

Hope this helps. Maybe if we saw a picture of your band and threads we could help more.

Laverne

EDIT..........Just adding the link to Michael Cook's article-

www.weavezine.com/content/tablet-woven-brocade

 

 

Caroline (not verified)

As Laverne has said, you put the background weft through the complete shed, but you only need to have enough warp threads in that shed lifted up to hold the brocade yarn in place, say 1 in 4 or 1 in 3, depending on how long the floats are, the purpose of the band, and whether it will catch when in use. So while there will be 2 shots in that shed, the ground weft is the only one that goes through between every single warp and the whole length of the shed.

Do you have access to Mary Blacks "Key to Weaving", or"New Key to Weaving"? (same book, different editions) she goes into brocades very thoroughly from the most simple to the most complicated, and explains it very well.

You could also check out a couple of articles on Handweaving.net - those written by Suzanne Baizerman spring to mind, and i think Harriet Tidball and Mary Meigs Atwater wrote about them too, though for the 4 shaft loom, but the principle is the same. There are a lot of weaves with different names that use this technique, but the basics are always the same.

Hope this helps make things a bit clearer.

Thumper70 (not verified)

Thanks very much Laverne,

That was really helpful - and seeing in in action on your work too.

I've scanned throught the article you mentioned (thanks for the link) and am gearing up to give it another go. I've got a larger picture of my work as it is at present on the blog post ( here ) But it only has one line left of my attempt at the brocade. I'll be sure to give it another run then post an update.

 

Thumper70 (not verified)

Hi Caroline,

Thanks for your help - your suggestions about the binder thread - very helpful. I'm not familiar with Mary Black's book - but will look out for it when I'm next up at the Hand Weaver's Studio.

Between your and Laverne's tips I think I'm ready to give it another go. . . . . I'll post an update soon.

Thanks again

Alexis

 

bolivian warmi

You are welcome! You are really zooming along with that inkle loom! Congratulations! I pm-ed you some more useful ''stuff''.

Laverne

Aunt Janet (not verified)

OOOOO!  Sneak preview!  Can't wait to see this tutorial.

Aunt Janet 

Thumper70 (not verified)

Thanks everyone for your help - I think I'm starting to get the idea.

Sorry for the washed out pic (used my laptop web cam rather than a proper camera) - but my first shape - albeit a bit wonky in spots - seems to have been a success.

My plan is to do a few more geometric shapes, throw in some animals, and do a sample of lettering as well.

I'll post an update when I've got more to show for the effort (grin).

A

bolivian warmi

Yay!!!!! :-)

Would LOVE to see the lettering!

Laverne

Caroline (not verified)

Way to go!  You've got the idea! now you can play and develop your technique!

Happy New Year!

rose Goldielocks (not verified)

good job, great to see that all the "light bulbs" turned on in the apropeat places! Its is always great to see when someone "gets it" for a new techniqhe!

Have a wonderful and happy new year!

Sharon..

Submitted by Anonymous (not verified) on