Does anyone out there know how to convert warp for rep weave from 16/2 to 3/2? I don't want to use 3000 heddles instead of a more reasonable number plus I have a Jack loom not a counterbalance.

Comments

Claudia Segal (not verified)

Since 16/2 is finer than 3/2 you would have fewer heddles in rep weave with 3/2.  How wide is your project?  What is your sett?  Have you used a weaving calculator or just a piece of paper to figure the details of this project?

There is a simple weaving calculator HERE and a class with Mary Rios who also does private classes, HERE.

Claudia

Karren K. Brito

Rep weave needs a fine warp and a thick weft  so that the warp bend over the weft to cover it, as seen here. Moving from a 16/2 to a 3/2  and no change in weft will give you a totally different type if weave, more balanced. I'm not sure using two 16/2 ( reducing the # of heddles to 1500) would work but it seems more likely to give this kind of a structure albeit with wider spaces between warp bouts covering the thick weft.

If you are not ready for 3000 heddles , you may not be ready for this weave.  What are your goals and is there another weave structure to get you there?

Sara von Tresckow

Do note that when using 16/2 cotton for rep weave, in the Scandinavian version it is often DOUBLED in the heddles as 2 threads in a heddle cover the weft better than a thicker single thread.

Now you're down to 1500.

3/2 cotton is very thick, not very flexible compared to finer weights and is not going to give the results you see in a book using 16/2 doubled.

You might want to consider 8/2 doubled in 750 heddles - coarser than called for, but acceptable in appearance when finished. And here you'd want to bulk up your thick weft.

Joanne Hall

In addition to what has been said, remember that with a jack loom you should open up the sett a little.  If it is a four shaft weave, spread it out on 8 shafts.  Even doing this, you may want a little more open sett if your warp is wide.

Joanne

pajoline (not verified)

Doubling the 16/2 sounds like an option. I have done a couple of rep weaves from patterns in handwoven magazine. They had used the 3/2 and did come out nicely. I recently purchased the new addition of Rep Weave and there were some patterns I liked but all done with the 16/2. If the sett is 36 end per cm can tou get away with using the same sett with different material as long as you take in account that the thick thin weft?

kerstinfroberg

Still rep, but not quite in answer to the questions:

there is another option - half-rep or open rep (don't know what to call it in english). Here, the idea is to use a warp in different colours (same as the "original"), weave with thick and thin (as the original), but to get an additional effect from the visible (thick) weft. For instance:

In my guild we have had an autumn concentrating on rugs - se more pictures here. There are two examples of half-rep in our calendar for 2005 (the one above, and the January room dividers).

ncmagyar

Is this Rep Weave? I bought this potholder at the local guild sale and love it!

(wish posting pictures was easier)

 

rosslyn lyall

I have never done Rep Weave before but am in the process of setting up 60 Inch weaving width rug on my newly acquired AVL 16 harness production loom. I am using a pattern from Kelly Marshall's book Custom Woven Interiors and am using carpet wools I have dyed. They are varying thicknessness and twist. I think I am trying to do a project way beyond my skill level and knowledge but ready to learn and determined to do the best I can. Is it possible to weave Rep with carpet wool or does it have to be a finer thread (cotton). I have posted a question in AVL group also because I am having trouble with the warp (Sectional Beam) and having thread many many heddles do not want to lose this work. My question here is do I continue to sley the reed and attach to front bar, take off the sectional beam and rebeam with the warp on the plain beam and what steps do I take to do this to get a warp with the tension I need on the AVL loom? Any assistance/advice would be most welcome. Thanks in advance. 

 

s 

Deirdre King

I once wove a couple of warp-faced rugs, inspired by Peter Collingwood's book.  My biggest issue was that I tried to use a reed that was too small for the project.  Meaning the dents per inch were too closly set.  It was almsot impossible to open a shed and clear it.  I used carpet wool and I want to say I set the warp at 15 to 20 ends per inch (two ply wool).  It was a tremendous struggle but I did get two nice 36 x 72 inch rugs when I was finished.  Also, think about the end finish--a hem works best because with such a dense warp the knots on the ends are painful to walk on

Submitted by Anonymous (not verified) on