I am working on towels, and the pattern indicates 24 ppi.  To make the hem, the draft requires 18 repeats of 2 picks (plain weave). When I completed  weaving  2 picks 18 times (36 threads) it was 3 inches.  The written instructions for ending the first towel (and starting the second) indicate 1.5 inches for the hem.  Clearly, 36 threads should be 1.5 inches if weaving 24 ppi.   

Everything else about these towels is consistent with the measurements noted in the directions, and I use a firm 'beat' .  What did I miss or do incorrectly? 

Thanks! 

 

 

 

 

 

 

 

 

Comments

Erica J

Is the entire towel woven in plain weave? It is still early morning, here, so maybe I'm wrong. But I believe that plain weave will beat in differently from say a twill.

So let us know what towe you're doing, structure, materials, etc and we'll help you figure this out!

Have a great day!

Joanne Hall

If you have 8/2 cotton, warp and weft, you would get about 20-22 epi with plain weave.  If your warp and weft are 10/2 cotton, you should get 24 or more.  But if you are weaving on a rigid heddle loom, it is hard to get this many per inch without using a batten or the edge of a stick shuttle to squeeze a tighter weave.

What warp and weft are you using?  what loom?

Joanne

cmsbcg

Thank you Joanne and Erica.

I'm working on 'Dorothy's dozen twill kitchen towels' from Handwoven, Sept/Oct 2014, using 8/2 cotton for warp and weft on my 8 shaft floor loom (Mighty Wolf).  Plain weave is used just for the hem.

 I started the next towel, and am beating each pick twice, but have not been able to achieve 21 picks per inch.  

Any suggestions will be very welcome!

Barbara

 

Artistry

Hi cmsbcg,

The problem is simple, and simple to fix:) plain weave has more interlacements than twill. That is , plain weave goes over one, under one and so on. Depending on the kind of twill you're doing, it will at least go over two and under one,or the reverse, that's a three thread twill. I suspect your twill float is longer than that since you're using a 8 shaft loom. So if you think about the twill , you don't have to use as much force to beat down the weft , because of the interlacement not being as close as plain weave. Does that make sense to you ?  Plus the sett for twill will be closer together than for plain weave,  it will actually give you a slightly warp faced plain weave, meaning there are more epi, than ppi in the plain weave. So that makes it harder to beat down too.

so how do you get around this? I would  simply use a finer weft for the plain weave area. Try a 10/2 first. Or , if you're not too far into the next towel and have ample yardage on your loom, you could take off your first towel and wash and dry it. See how the 8/2 looks in the hem. it will still be long, but it will have shrunk, look to see if the weave looks good. Will it be too bulky when it's folded under too hem?If it looks fine, then I'd use the 8/2 and just make the hem the required length or maybe a little longer depending on shrinkage.

be aware when you go from a plain weave area to a twill area there will be a flare to the cloth because of the different ways the structures interlace.the plain weave area being wider than the twill. I Think the way around this is to use a finer weft, so , the 10/2 come to think of it may be your best bet all around. 

Does your hem get completely folded under?

Hope this helps,

Cathie

Joanne Hall

Not only will the temple make it easier to beat and get 24 per inch or even more, but you will get a more even beat and it will be easier to beat. 

Joanne

Artistry

That's a good idea Joanne! I don't use a temple, but can see how this would work. It would make the plain weave wider, hence making more room to beat down the weft. Is that correct? 

Cathie

Joanne Hall

Yes, without a temple, the selvage warp threads start to get closer together than they are at the reed.  It becomes hard to beat in the same number of wefts as when you wove the first inch.  At the selvage, the weft cannot beat in as much, so the selvages will sit a little higher.  It is just easier to have the temple holding the warp out to the original width.

Joanne

Submitted by cmsbcg on