I am currently using alot of 60/2 silk and plan to move on to 120/2 silk in the near future.

 

I am finding that my weaving software is not wonderful for drafting designs for the fine threads. It is not uncommon for my drafts to have 1700-2000 ends at 60 epi.  The problem that I run into with my weaving software is that, even with a really wide monitor, the software is unable to compress the image of the design enough that I can view the entire width at once. At best I get about half of the fabric in fabric view.  This makes it very difficult to see how the pattern I am designing will scale.  I’ve been cutting and pasting sections into other software, so far this is a cumbersome and only marginally successful process. 

 Does anybody have recommendations?  I am chiefly designing drafts in network twills.

Thanks much,

M McLaughlin

 

Comments

danteen (not verified)

I use Weavepoint.  It allows 2400 ends and maybe more, though I don't usually have that high a number of ends.  I often have 3000 picks or so in a scarf.

But I have a 27 inch monitor  set at a high resolution to see as much as possible of my design.   I'm not sure if it is a software recommendation that you need, but a large monitor.   You can also set up two monitors in Windows through the Control Panel and put all your extra panels for the software on the second one.  It is also possible to get a monitor that allows for it to be turned with the shortest dimension horizontal and the longest dimension vertical for long designs.  newegg.com is a good place to get electronics.   That was a suggestion from my son the computer programmer.   Also, a business recommended in Consumers Reports.

Teena Tuenge

M McLaughlin

Teena, thank you for all of your suggestions.

I think you may be correct about the monitor; mine is 21". Wider would certainly help. However, I'd prefer not to have to purchase 2 new monitors--my husband might notice that LOL

We're a Mac based household, which unfortunately limits some of my choices. Weavepoint seems to offer a much better range of options than the software I've been using. I'm wondering if I can use it on a MAC with Crossover or Bootcamp. I'm going to look into it. As my setup exists now, I don't see a good way of viewing my drafts for the 120/2 silk that will soon be arriving.

Thanks again,

Molly

 

tien (not verified)

My recommendation would be to use a program that can export a draft to an image file (Weavepoint will do this). Then you can view the image file in Preview or Picture Manager and it will resize it down to something you can view on your screen without scrolling.

I work a lot with fine threads as well, though my repeats are generally considerably smaller, so it's not a big problem for me. On the occasions that I've done network drafting, I've either "printed" the design to PDF and then converted the PDFs to images via Photoshop (very tedious, as you've noted) or else printed directly and then taped together the images. Exporting to an image file will likely be much more civilized.

If you would like to see how well this works, PM me a .wif file and I'll try exporting it as an image in WeavePoint for you.

M McLaughlin

Thanks, Tien.

I'm PMing you LOL

ReedGuy

Some overshot patterns such as Bradock's Defeat can pose the same issue you speak of. There is always a way to the destination. Myself, I had to print the draft wide anyway in order to read it. Squished up small on one page was impossible to follow. :)

M McLaughlin

Thanks, ReedGuy.

At this point, I'm looking at installing Weavepoint. Tien awesomely took one of my wif files and exported it to an image demonstrating that the software has the capability of showing me the draft in it's entirety.  Since then I've been rubbing my hands together and chortling.

Now if I can figure out some of the issues I forsee in dyeing and warping the 120/2 silk that I'm going to be designing the next draft for, I'm going to have some fun!!!

Molly

Submitted by M McLaughlin on