I am a beginner and have recently acquired a vintage 4 shaft counterbalance floor loom.  I have read some places that it impossible to do an unbalanced weave (3 shafts against 1) on one of these, where other authors say that is no big deal and works fine.  What do you think and if you do unbalanced weaves on a CB loom, is there anything that can be done to make it work better? 

Thanks, Friends

Candace

Comments

Bonnie Datta (not verified)

Hi Candace.  I've done many unbalanced weaves on my Leclerc Fanny 4-shaft CB loom and never found it to be a problem, assuming that the warp is evenly tensioned etc.  I have just 6 treadles, so I often tie up the tabbies (1&3, 2&4) and use the remaining 4 treadles for direct tie up.  Then I can treadle any shed I need, using 2 feet if needed.  I also find that this way I can control the bottom layer of the shed very easily to keep it nice and level.

Bonnie.

naturalfibres (not verified)

When I started weaving I was never told this, so it never stopped me from doing unbalanced weaves and I don't recall ever having problems.

The only time I did have a problem was when I did a 3 thread huck on a CB - the threading only uses 3 shafts, so shaft 4 wasn't threaded at all.  This caused shaft 3 to roll down as far as it could and shaft 4 to roll right up.  I solved this problem by tying metal rods to shaft 4, and then happily wove away.

peg.cherre (not verified)

I agree with the previous writers - it can be done.  I have a handmade (not brand name - probably own design) vintage 4H counterbalance, and have done many lace weaves, and doubleweave, on it.  My shed isn't as large as when I do balanced weaves, but it's not bad.  

My suggestion -- when you're doing unbalanced weaves, modify the ties on the top roller bars (if possible) to lift the bottom roller bars as much as possible without interfering with loom operation.  This gives you a bit larger shed.

I have some posts on my blog about doubleweave and lace weaves, both on my counterbalance loom.

kerstinfroberg

In Sweden we don't know that it is impossible, so we do it all the time... usually, though, it is recommended that weft-faced twill (3/1 - or should it be called 1/3, I can never remember which number should come first) is woven as warp-faced instead. This, however, is because it is easier to spot mistakes from the reverse.

Lynsul01

I have Jennifer Moores DVD for doubleweave but I have a counterbalance loom. I don't know how to tie it up.....please help.

ReedGuy

How many shafts? If only 4, than you can only do plain weave. You create two sheds, while half the shafts are lowered the other half are raised when going between layers and the pattern tie-up is mirrored between layers if you are making double wide cloth where the fold is on one edge and open on the other. Also the sett must be doubled.

A simple diamond twill double wide project can be done with 6 shafts.

 

pammersw

Thanks for the doubleweave illustration,  broken down! It nearly makes sense, now, I can almost picture it. When I have more shafts,  I will try it! I'm limited to plain weave if I try it now.

ReedGuy

Yes, and you can do a tube if you treadle one shed then the other instead of making a return trip on the layer started. top, bottom, top, bottom instead of top, bottom,bottom, top, top......

 

You can manipulate things further. Say you have a draft that is good on both sides, one is weft faced, other warp faced. You may want to weave a pillow case that allows you to show one face this week on the couch, and next week another. Some will think you just got a second pillow case next week when they walk into the room and you can grin about it before you reveal your magic trick. ;)

 

Or you may have a draft that is solid color on the back side of the pillow , say white, and pattern on top. Instead of mirroring the pattern in the tie up, leave the same so opposites show, depending on which side of the pillow case is in view. This applies to the previous paragragh as well.

tommye scanlin

The ability to weave a background and then do hand-manipulated weaves like leno, Danish medallion, Spanish lace on top is quite nice.  If the layers are different colors, then the layers can switch places with the open work effects showing different warp color.

Then there's double weave pick-up technique, using only 4 shafts and the two layers in contrasting colors.

In my thesis work years back I combined warp rep with double weave in structural pieces (possible since the density of the warp sett is twice what one would expect for one plain weave layer--push it a bit more to make for more warp dominance in each layer...)

Doubleweave for four shafts has loads of potential!

Tommye

 

loomyladi (not verified)

Yes, it will work.  It's good and bad and can be pretty, but can also be a royal...well, you get the idea.  I just finished my second set of waffle weave towels on a Fanny LeClerc.  OK, so since I did my second set one would presume that all went smoothly....well I had move and had to make some loom adjustments.  Once I got all the kinks of the sheds worked out and adjusted tieups etc.  All went well.  I've started winding the warp for the third set of towels for the same loom, same pattern.  Goodluck

pammersw

Ok, I understood most of those words, LOL!  :) I do get the plain weave double cloth, I just hadn't figured out how you had done your diamond twill blanket! Now I have an inkling...an "aha" and "now I see...I think?" moment.  As soon as I try one for real, it will all click. ;)

ReedGuy

Get a legth of string and a peg board. About 12" apart, put a peg one above one another, so you have an outline of a rectangle. Tie onto the upper one on the right. Now wrap that yarn over the left top peg, down under the bottom left, across to the right bottom. Loop over the bottom right, back to the left and around the outside of the bottom left, up over the top left, back to the top right. That should be the same path you read in that draft. That is equivalent  to starting on the right, sending the shuttle left, then return it to the right on your scarves. Follow that in the treadle sequnce of the draft. Now it is much clearer. So now you see it is twice as long to go any distance in advancement of the weave. :)

pammersw

Yes, I get the shuttle path. I just didn't know how to put a pattern in it. 8 shafts is the answer.  :)

And I only know about half the weaving terms like rep and such, LOL!

kerstinfroberg

While it is true that most weaving software can do an "automatic" DW/DW (Double Width/Double Weave) it can be interesting to actually know/understand how it works. One of my favourite methods is to make a small paper weaving, fold it where I want the fold and then make an analysis. One (actually two) descriptions of how to do this can be found on my website, here. 

I'm not patient enough to weave finnweave (or pick-up(down between layers), but I like playing with loom-controlled double weave(s).

ReedGuy

If it's something double wide, just remember to get the same thing (pattern) on the bottom layer so that when it unfolds off the loom, your tie up for the bottom has to be reversed that of the top. So you can see, when still on the loom by looking underneath, that the pattern is developing the same as on the top side that your looking at from your bench. If you look at the pattern window in the drops, each pixel is represented by two treadle pressed, one for the top one the bottom. So that one weft shot on top gives the same pattern on the bottom when the weft passes on the bottom. Looking at the first two ends, you can see that shaft one is pulled down, then shaft 6 is pulled up, so obviously the weft is dominant because the warp ends are pulled toward the centre of the cloth in each shed, the wefts outwardly on the cloth.

ReedGuy

Me either Kerstin it would drive me to insanity. I want the loom to do the work and no fiddling. Now when it comes to wood working, I can fiddle around all day and get nothing done, and still enjoy it. LOL Right now I'm working on a fiddle back design for my chair, I am using cardboard to make a draft/design to see how it comes to life before making scraps out of wood from improper cuts and angles. Lots of fiddling, nothing actually done. :D ;)

ReedGuy

I find that once you can read a draft, it just comes. But Kerstin's method is one of many that helps you understand a draft. There are some things software does not show, like pile formation. All I see in software is an absolute mess that looks like it would fall to pieces. So learn it the old way and your far ahead of the curve. :D

Submitted by celtinbirks on