I have an older Glimakra 8 shaft countermarch and am having the worst time getting clean sheds when I work with more than 4 shafts.  I've read quite a few guides in English and German but don't seem to be able to wrap my brain around the technique.  Any suggestions as to getting further?  When I get one shed pretty good, the others loose their balance.  It is as if the interaction between the lamms gets too tight and they do not move far enough to open the shed.

 

Any help would be very welcome,

 

Jamie

Cologne

Germany

Comments

Joanne Hall

Hi Jamie,

We have instructions on our website.  The third file is about the countermarch.  Before the early 80s, the lower lamms were the same length as the upper lamms.  As weavers started to be more interested in weaving with more than four shafts, the lamms were made longer for better balance.  Our website instructions discuss this and tell you what to do if you have one of the older looms.

Joanne 

It is here:
http://glimakrausa.com/learning-looms-weaving/intro-to-countermarch-and…

gartenweber

Joanne,

yes, I have the short lower lamms.  I think I'll need to have some new ones made with weight.   I tried tying up extra treadles, but it didn't work.

Thanks for the input!

Jamie

Joanne Hall

The extra treadle is tied up only to the long lamms to add the weight of the treadle to the lamms.  Try it.

Joanne

sandra.eberhar…

Instead of replacing them, you might try weighting them.  The reason for making them longer is to make them weigh more.  I attached steel rods to mine with electrical ties.

gartenweber

Thanks, I had been think about trying this, as well.  I would prefer to have longer lamms in any case, but was looking into adding some lead to the ends.  I though of boring the ends an pouring the liquid lead into them.  How much additional weight did you find a good amount?

I've, also, continued to try balancing the short ones, as I won't be able to get anything for lamms for another week and am learning a great deal more about balance in general.  An interesting, if frustrating study.

cheers,

Jamie

 

pammersw

What about a less permanent solution first, to test the idea? Try taping some coins to them. A dollar or two in quarters is a lot easier to remove if it doesn't work.

pammersw

What about a less permanent solution first, to test the idea? Try taping some coins to them. A dollar or two in quarters is a lot easier to remove if it doesn't work.

Kelly Range

 The weight of 6"-12" pieces of small rebar taped to the ends of the lamms would aso work. may not even need that much. Longer lamms work on my Glimakra. 

Joanne Hall

The extra treadle is the easiest way to do this.  If you are using all your treadles, just use a board shaped like a treadle.  You only need to tie this treadle to the lamms of the shafts which fall.  And if the weight of the treadle is not enough, just tie a weight onto the treadle.

Read more on our website at the link I put into the first message. 

There is no need to adjust any cords in the tie-up.  They are put on one time and only the treadle cords need adjusting.  And that is only to perfect the shed or to make the shed larger or smaller.  Adjusting any of the tie-up cords will not keep the shafts from falling.

Joanne

sandra.eberhar…

Joanne's suggestion of adding another treadle is the easiest way to add weight.  I added 1/4" steel rods to my long lamms because I have no room for another treadle.

Joanne Hall

Yes, adding weight to the lamms does work, but sometimes not all the long lamms need the extra weight.  Usually it is just the front one or two.

When there is no room for an extra treadle, you just tie it to the treadle beam.  It is not used as a treadle, so it does not have to work as a treadle.  It just needs to stay in place and be out of the way of the other treadles. 

Joanne

gartenweber

Joanne, as I understand you, one would first tie all the lamms with the shafts held in place with the top pins and, when the pins come out balance the shafts by modifiing the treade cords to the lamms.  This is what I had started, but found it very diffcult to get a balance without shortening/lengthening some of the tie-up cords.  I had started with the 1-1-1-2-2-3-4-4/5, but couldn't get a balance.  I found that playing the cords closest to the lamm pivot made a difference.  They do not need to move as far.

Yes, the first two shafts are the tricky ones, followed by 3 and 4.  The rest are much easier, but seem very weighty. I take it this is reflective of the angles of the loom, if you follow me. I picked up some iron rod this morning and am going to drill holes into the ends of my current lamms and add lengths of rod to get a better balance.  I first wanted to replace the lamms, but this has proven a bit more difficult that expected.  Weaving is not as popular in Germany and resources are limited.  I looked at wood to make my own, but none was straight enough!

I want to thank you all for your input.  I am a bit taken aback by the help offered.  Wow, is the word.  Thanks!  All!

Jamie

Cologne

Joanne Hall

The important thing to remember about the tie-up is that the sinking of the shafts, which you experience when you take the pins out, is solved by adding weight to the lower lamms and the easiest way  to do that is to add a treadle tied to the lower lamms. 

You should not adjust any tie-up cords on the loom.  The only cords which are adjusted after your loom is set up are the treadle cords.  And these are only adjusted if you want the shed to be smaller or larger, or to perfect a shed if one or more shafts rise or sink too much when you open a shed.  And this adjustment is done on all looms, not just a countermarch loom.

Joanne

Joanne Hall

PS  The most common mistake that weavers make is to tie treadles too high.  Not only is this uncomfortable, but it also can complicat the tie-up.  It also makes the shed much larger than is necessary, leading to selvage problems.

Joanne

gartenweber

Thanks!

I'm storing all this away and, yes, I think there is an epiphany-like effect coming on.  Then, again, you do make it all sound so easy!  I suppose it is, if you just let it.

 

cheers,

Jamie

Submitted by gartenweber on