I don't have a sectional beam and all the tools that go with it.  I do have to do several warps of many threads (940).  I do use a warping valet and beam under tension.  Still lots of my cotton threads are sticking together and making the beaming take a long time.  Here's what I'm wondering...

If I got a sectional beam for my loom, could I use it in combination with more traditional warping methods.  Specifically, if I measure say 3" of warp on my mill, use my valet and keep the warp under tension, could I successfully beam those three inches, then move on to the next three inches?  Or would that be just begging for trouble?

Thanks for your thoughtful advice!

Peg

Comments

sally orgren

I tried a variation of this on a much smaller scale. The more open sett and short length of warp (5 yards) had a lot to do with my lack of success. Although I wound the warp on the warp board and sectioned it off, the sett for each section wasn't close enough together, and the warps clumped up to one side or the other in each section.

I might have had better success if I had thought to use my tension box beaming into each section. (Duh!) My flawed method was to weight all the sections evenly, and beam them simulatenously. I should have just beamed one section at a time. I did not use an overhead valet, I was using water bottles hanging from the bottom.

I think it could work with the valet and a tension box with reed that will distribute the warps evenly in each section. You could try it with just one section from all these warps and see how it goes, right?

 

MMs-and-OOs-Ha…

You certainly can. You might want to stay within the sections of your sectional beam. I have a 1" and a 2" and, depending on the sett of my yarn and what I am doing, I will use one or both. I have never tried beaming wider than the section. It might be doable if you have the metal rakes. On my beams the wooden pegs can snag the yarns. I just put on a small warp yesterday on my AVL 1 yard 2" sectional. I measured out 5 yards, 12" wide, 16 epi, 32 ends in six sections. I made a threading cross and a raddle cross. I attached the raddle end of my 2" section to the leader on my beam and then kind of eyeballed where to put the raddle cross bouts in the raddle. Since it was so easy to do I just hand-tightened the section of yarn while I turned the beam and then pinned down the threading cross end of the beamed section of yarn and continued. When all my sections were filled I unpinned all of the threading crosses, let'm dangle, and then inserted some lease sticks in the cross. All of the warp is now hanging from the castle ready to thread. Generally sectional beams are bigger in diameter compared to a plain beam. This helps distribute the warp tension, so the warping valet might not be necessary. The main thing is you want flat sections. If you were loading more, to keep your sections flat, you might want to invest in a section box with a pivoting reed.

mneligh

I do this routinely, using my tension box.  However, I never beam more than one section at a time.  I do not use a cross, but tape the ends as they come through the reed of the tension box.

Peg.Cherre (not verified)

So I'd need to buy a supplemental beam and a tension box.  We're looking at more than $500.  I don't think I can do that.  I guess I'll have to find another way to make this easier.   

 

Artistry

Peg.Cherre, When you warp do you use two warping threads at a time? I find having two threads laying side by side in the cross instead of one over one under,, really helps cut down on the sticking. If you do this already, just brainstorming:)

Peg.Cherre (not verified)

I do wind 2 threads at a time when I measure the warp.  I think the real problem is that these threads are so close together - sett is 30 EPI for 8/2 cotton.

Artistry

Yes, that would do it. What are you weaving? Sounds intriguing! I've had a couple of warps where I've used merino wool/silk, silk single, silk 2 ply sett for satin , they were very sticky and hard to beam. So I know where you're at!

mneligh

I don't think you would need a tension box -- the valet should work for tension.

On the other hand, I'm been keeping my eyes open for something to use as removable sectional strips for one of my looms to which I don't want to add a sectional beam.  I was thinking pegboard cut into narrow strips, with metal loops as dividers.  That way I wouldn't have to drill the beam which I'm reluctant to do because I was planning on removing the loops after use (you only need one set, 4 places around the beam) and I think the holes would wear over time.

These dividers are important in keeping each section from spreading.

I want the loops to be removable because I want the loom in question to still fold in order to travel.

I extend the challenge to everyone out there -- what can we use to create temporary sections on a warp beam?

Sara von Tresckow

How many chains are you currently using for your 900+ threads?

I'd be making at least two, maybe three. Oddly, very small chains (less than 100 threads) or very large chains (over 400 threads) tend to stickiness.

I usually make a chain for every 9 - 12 inches of warp width - and also place the raddle in FRONT of the least sticks when beaming. (Using quick release clamps, the raddle can be mounted most anywhere on a loom.) The raddle separates the threads into manageable groups so that the lease sticks are not burdened with the task of separating the warps. Also, I do not make warp chains with single fine threads, somehow, fine threads separate much better if you warp with 2 threads at a time - putting your finger between them to keep them from twisting.

ReedGuy

I could suggest how to do it, but I have the tools and it's not practical for those that don't have the tools. Once the sectional attachments are made, secure with screws at the ends of the wooden sections that can be easily removed. You would need more depth for the holes than peg board I think. Your loops would soon be leaning away from vertical, and probably fall out.

I'm like Peg, I have tried fine yarn (some might not call fine), but had a mess of knots. If you could manage narrow bouts with lots of ties and keep them separated while transferring to the loom and tensioning that is the trick. I find the stuff is loopy and once you pull on a bunch of loopy thread it goes to knots real fast. Hard to even make a slip knot that doesn't synch up tight when pulling the tail. Gets old fast. :)

mneligh

A good farrier can make horseshoes from scratch -- I'm talking plates, not kegs, or at least that is what I've used on my horses.  They can be aluminum or even titanium as well as steel.  A high-end horseshoe can be drilled and threaded to take screw-in caulks for various types of surfaces.  I wonder how much it would cost just to get the strips and pegs or loops made.  It might last longer than the same thing out of wood, and lie flatter.  It might save me some money if it didn't have to get fitted onto a horse.

ReedGuy

Over engineered for the task. LOL! :D

"I know engineers, they love to change things" Dr. Leonard McCoy , USS Enterprise

mneligh

The shoes aren't overengineered, but I might agree with you about the beam.  I talk to farriers on a regular basis, but not woodworkers, so they're handy in my contact list.

In any case, you got the profession right.

Peg.Cherre (not verified)

Lots of this discussion got way over my head!

Anyway, in answer to questions: Cathie - I'm making baby wraps.  They have to be very strong.  I may find 30 EPI too dense, but that's what the rosepath in the latest issue of Handwoven was, so that's where I'm starting with a heart twill.

Sara: I made 5 chains, each between 150 and 220 threads.  Too many?I did have the 2 small cones (not the tall cone-shaped, the smaller tube shaped) cones each on a dowel in a milk crate, coming up through an extra reed.  I did not, however, separate them with my finger while I was winding.  On a mill, would this be tricky?  I like the idea of the raddle before the lease sticks, except that then I couldn't use my valet unless I had another set of lease sticks.  My old handmade mill doesn't currently have the capacity for two sets of crosses.

Also, here's another mistake I made...In order to be able to move the lease sticks from near the raddle to the front of the loom to use with my valet, I had to spread the warp to less wide than it will be in the reed - instead of 30 EPI that it'll be in the reed, I set it at 40 EPI in the raddle.  I plan to use a different set of lease sticks that will let me spread the warp out to the planned 30 EPI and/or try to figure out how to make a second cross for the next warp.

I'm also going to weave a full length wrap, cut it off, wet finish it, and have actual babywearing moms test it out.  Maybe I can make future wraps at less EPI.  (Can you see my crossed fingers?)

Thanks for all your input, and keep it coming!

Peg

Artistry

Peg.Cherre Looked up your project for the baby wraps, they're awesome! I would have loved to have had one ( or two! ) of those when mine were young, many moons ago! You're right they have to be strong. I noticed they're using 10/2 @ 30 epi, I believe you had mentioned that you're using 8/2 @ 30 epi. Maybe that's just a typo. But if not, you might want to open that sett up! Do you have the free download Master Weaving Chart from Weaving Today? They suggest 24 epi for 8/2 pearl cotton, twill. You've gotten a lot of good advice, just my two cents:) Good luck with your project

Peg.Cherre (not verified)

Yes, Cathie, I'm using 8/2, not 10/2.  Although both my heart twill and the rosepath have only 3 thread floats, I'm still worried about strength.  There are safety & liability issues with baby wraps. 

I also recognize that baby wraps need to be flexible, so will keep that in mind in my finished product as well.

I do use the Master Weaving Chart as a guideline, but it depends on your intended purpose.  So for this first one, the sample I'm setting it at 30 EPI.  I'm hoping to be able to reduce the sett some, but I doubt I'll be able to go down to 24.  (I'd be really happy with 26, actually.)  Only time will tell.

Artistry

Peg.Cherre I hope you'll post your results down the road! It would be fun to see the wraps, and wonderful to see your work on them!

Sara von Tresckow

1. Putting your finger between the 2 threads is something that you don't even think about after a time or two. When running the warp thread, you simply leave that index finger between the threads.

2. Its not clear why you need the lease sticks toward the front of the loom because of a valet. The valet is there to lengthen the path of the exposed warp - the raddle and lease sticks can certainly remain behind the castle - raddle first as the warp winds on the beam.

3. It would certainly be of benefit to you if you can figure out a way to mount the sticks needed to make a second cross on your warping mill.

4. Compressing your warp to 40 epi for the beaming makes the threads much closer together when beaming on - that may be causing some of the stickiness.

I still don't use a "valet", but the "weavers best friend" concept of Andreas Moeller - I wind the chains around the breast beam or other cross members on the loom to provide the necessary drag and it works quite well. For tricky warps, my husband is quite willing to help out and he stands across the room as the "valet" and handles the chains, which is really a nice way as you can monitor things as they progress and catch any issues as they arise.

Submitted by Anonymous (not verified) on