Hello,

I recently acquired a Le Clerc Dorothy table loom but have no idea how old it is or what parts are missing from it. The serial plaque says, "DT 4L 40 cm 78-09" so I'm assuming it's from September 1978 & is a 15 3/4". Can anybody tell me what the "DT 4L" means?

Also, each shaft only has about 40 heddles on it, are these easy to replace? The beater is taped up so I need to replace that too. Where is the best place to order parts? And what else should I be looking at to see if it needs replaced? Would uploading some photos help?

Any information or tips would be greatly appreciated, I am looking forward to learning how to weave!

Thanks,

Lori

 

 

Comments

pammersw

I'd start at the LeClerc website. They have drawings and photos of their various looms, so you could figure out if anything is missing. They can also sell you any parts you need. They still make the Dorothy loom, although it might have changed a little over the years.

lalaloom

So is Camilla Valley a good website to order from with decent prices?

I see it says that the Dorothy 15 3/4 should have 400 heddles in total - so do I put 100 on each shaft?

SallyE (not verified)

I've had very good experiences with them.   As for prices, they sell for about what Leclerc does.  Everyone is going to be about the same price.

The number of heddles on each shaft depends on your pattern.   Those looms only weave about 15 inches wide, so with 400, that's and epi of 26 or 27.   If you have a weave you want to do that's 30, for example, you will need more.

suem

The DT stands for "dorothy" and the 4 L means that it has 4 lames, or 4 shafts in English:) 

and you are correct about  the date of manufacture being September 1978.

 

lalaloom

Wow, this thing IS older than me! Thanks for the confirmation/information!

I'm still unsure of what I need to get it going & what (if anything) is missing or needs to be replaced. I've sent an email to the Camilla Valley people, hopefully they will be helpful - thanks again!

Sue in VT

Hi, I, too, acquired a 1970's Dorothy. If you go online to Leclerc they actually have the owners manual you can download as well as a diagram naming all the parts so you can ask for any specific parts. I bought new heddles and put 100 on each shaft. Once you dress this loom to weave you'll understand why it's a classic! User friendly and dependable!

sally orgren

How much did everyone pay for their vintage Dorothy's? (Or was the loom a gift?)

I borrowed a Dorothy from my guild for the first two years! They are great.

khakijean

I paid $225 for my 1970s Dorothy about a year ago and later got a 1950s Dorothy free.  The 1950s Dorothy was missing the wood for the beater and shuttle race (the arms are metal), but my husband was able to make them for me using the 1970s Dorothy as a guide.  I like using them for small projects. 

Weavingholiday

I got my 24 inch Dorothy for $200 a couple of years ago. It came with the treadle stand, had all the needed bits, 2 shuttles, 3 reeds, and assorted lease sticks, bobbins, threading hook, books and even some mystery fibre.

As you can guess, I bought it from a generous friend, in this area 15 3/4 Dorothies seem to go for around $150 to $200, but not usually with so many nice extras.

On the other hand, they do also pass from one weaver to another for free sometimes. They are a solid, reliable, and refurbishable work horse that has stood the test of time.

SallyE (not verified)

About 18 months ago, I was looking for a 3d shaft "box" for my long frame Dorothy - bought new in the 1970s.   It already has 2 4-shaft boxes, and I wanted a 3d.   I saw a Dorothy with 2 shaft boxes in RI on Craigs list and contacted the person.  I asked whether they would be willing to sell me just one of the 4-shaft boxes.  They said sure.  I used their asking price as a percentage of the new price to calculate how much one of the boxes would be as the same percentage of new, so that they could sell the rest as a whole loom, sell me the box, and get the same price in the end.  

Well, I got a rather long and really nasty email back, saying I was awful for "using my math skills" to get the better of someone else, and they were blocking my email address!  They still have just the box listed for $175.   I'd offered them $110 for it.

Well, a couple of weeks later, I found a whole loom with one 4-shaft box for $100.  So, now I have have 3 4-shaft boxes and 2 Dorothy looms.

I never realized that using math (arithmetic really) could be so threatening!

lalaloom

I purchased mine through Kijiji for $125 & it looks to be in exceptional condition. It came with 1 reed (which I incorrectly called the "beater" in my original post. Someone told me that the green tape on it was actually how they were sold in the 70's & it's not damaged or needing to be replaced) It also came with 1 shuttle.

I am now trying to find a warping board so I can use my loom but I am not interested in paying another $100 for one! I hope I won't have to sell my loom, I quite like it & I haven't even had the pleasure of weaving on it yet!

SallyE - that's horrible that they sent you a rude email! I find there are all sorts of odd people on Kijiji, it's really hit & miss!

kerstinfroberg

Don't despair! While everything is easier with the "right" equipment, improvisation often works, too. If you look ar Pammersw's project Christmas scarves, you also can see an improvised warping board.Probably not the ideal set-up for long warps, or for production -  but it will let you try weaving, at least!

PS - what the "right" equipment means can vary a lot between weavers... you need to find your comfort level compared to your budget

pammersw

I thought I would have to warp the next project on chair backs in the living room because it would be easier than on the legs -but I found a warping board at a garage sale last weekend,  so now I'm set. The looms and spinning wheels were priced too high, but I got the warping board, a kniddy- knody, and a ball winder for $63.

Badfaerie (not verified)

I just wanted to second the recommendation on Camilla Valley. I picked up a Compact last week from what was basically a sell out of a teaching studio. I got it home and assessed the parts I was missing and ordered from their website. I asked a few questions about possible upgrades as well.

I send the order late at night and I had a response the first thing the next morning. My parts shipped immediately and I got them in a week which is amazing with them coming from Canada.

I found them extremely friendly, helpful, a valuable source of information and they are a good advocate for the brand.

Weavingholiday

If there is a weaving guild or group anywhere nearby, perhaps ask if someone might let you use or borrow one until you can get your own?

igaff (not verified)

I had to order a part for my leclerc. Webs is also a supplier of parts and we're very helpful. Irene
Submitted by lalaloom on