Earlier today, I was sure that I had found the perfect old bobbin to fit a shuttle that I was given when I bought my first floor loom.  I was so delighted to have found the perfect bobbin that I snapped it right into the shuttle. Perfect fit! Unfortunately, I cannot get the bobbin back out of the shuttle. In my excitement, I forgot that I needed enough "extra" room to grab the rod that holds the shuttle so I could depress the hidden spring that keeps it in place. Does anybody have an idea how I can get this bobbin out of my shuttle? Or have I ruined it forever? Thanks for any ideas you have. (I've already thought of framing it and hanging it on my wall!)

Comments

Joanne Hall

I use a needle nose plyers.  Most woodworkers have one or you can purchase one at a hardware store.  You might try quills in your shuttle instead of bobbins.  They are easier to take out.

Joanne

Bonnie Inouye (not verified)

What kind of shuttle? Is it a boat shuttle with a spindle that pivots out? Or does the spindle pull out directly, or maybe have a spring? And old shuttle could also be an end-feed shuttle but those use pirns, not bobbins.

See if you can get a piece of strong string/yarn/thread around something that can be pulled out.

sequel (not verified)

I have one of these shuttles with the hidden spring.  If the pliers don't work (but I'm sure they will) you can get a saw cord at the hardware store, like a flexible saw blade, and thread it under the shaft to cut it off.  The same hardware store will be able to sell you a length of rod to replace the original (you'll have to cut it to fit yourself!)

cottageweaver (not verified)

Any suggestion about what kind of wire/rod to ask for at the hardware store? I have a couple of antique shuttles that no longer have the little rod in them. Thanks!

ReedGuy

Measure the hole diameter, it's probably 3/16" galv. rod, you can get it in 4' lengths sometimes short pieces in some hardware stores. Remember the hole in the quill or bobbin is probably 1/32" wider so it doesn't bind.

sequel (not verified)

If you are replacing the rod in a shuttle with the hidden spring, then you just take the old one or the shuttle in to the store.  (Hopefully you have a real hardware store and not a big box retailer.)

Older shuttles that don't have springs in the base of the bobbin shaft hole usually use a thin rod of spring steel.  A really old one probably used a flexible hardwood twig or bamboo or even the stripped shaft of a feather for a flexible bobbin shaft.

 

patle (not verified)

Thank you, everybody, for your helpful comments. I did try a tiny pliers, but it didn't help. All it did was shove the bobbin end down further on its shaft! The flexible saw blade sounds promising. I do have a real hardware store nearby and will take my old shuttle in for a consultation tomorrow. Amazing how you can become sentimental about your tools!

patle (not verified)

After a visit to my local hardware story, I have fixed my shuttle! They didn't have a flexible saw blade that cut metal, but did sell me a mini hacksaw and a short length of metal rod. It took me about a half hour to saw through the stuck bobbin and old  rod, then cut the new rod to fit. Yay! Thanks again for all of your advice and encouragement.

patle (not verified)

After a visit to my local hardware story, I have fixed my shuttle! They didn't have a flexible saw blade that cut metal, but did sell me a mini hacksaw and a short length of metal rod. It took me about a half hour to saw through the stuck bobbin and old  rod, then cut the new rod to fit. Yay! Thanks again for all of your advice and encouragement.

patle (not verified)

After a visit to my local hardware story, I have fixed my shuttle! They didn't have a flexible saw blade that cut metal, but did sell me a mini hacksaw and a short length of metal rod. It took me about a half hour to saw through the stuck bobbin and old  rod, then cut the new rod to fit. Yay! Thanks again for all of your advice and encouragement.

patle (not verified)

After a visit to my local hardware story, I have fixed my shuttle! They didn't have a flexible saw blade that cut metal, but did sell me a mini hacksaw and a short length of metal rod. It took me about a half hour to saw through the stuck bobbin and old  rod, then cut the new rod to fit. Yay! Thanks again for all of your advice and encouragement.

patle (not verified)

After a visit to my local hardware story, I have fixed my shuttle! They didn't have a flexible saw blade that cut metal, but did sell me a mini hacksaw and a short length of metal rod. It took me about a half hour to saw through the stuck bobbin and old  rod, then cut the new rod to fit. Yay! Thanks again for all of your advice and encouragement.

ReedGuy

The forum seems to go through hiccups at times, but the post usually goes through even if the page stops reloading for some reason.

Joanne Hall

Make a paper quill for your shuttle, which is at least 1 inch shorter than the spindle.  That way, you will have enough of the spindle open for your fingers to grip to take the quill out of the shuttle.  And, the paper will pull right out if you use up all the thread on the quill.

Joanne

Submitted by Anonymous (not verified) on