I just warped a  loom with continuous cord for the first time. This loom is set up for cords, but didn't have any, so I looked at different ways to attach the bar to the beam, and choose a single long cord so it wraps evenly around the cloth beam without bumps.  I fiddled with it for a long time and never got it really straight.  Is there an advantage to using cords instead of an apron that I'm not seeing?  All my other looms have aprons, or have single cords that create lumps on the cloth beam that must be dealt with.

Comments

Joanne Hall

Look on page 7 of my countermarch book. This is my preferred method.

Joanne

ReedGuy

I haven't Joannes book, but I used the Big Book of Weaving to set up my cords. My warp beam is big so I fashioned a long brass needle to thread through the beam holes.

The tie on rod with cords attached goes up over the back and over the top cross beam of course. ;)

sandra.eberhar…

The way your beam looks what I was trying to achieve, but how did you get it even?  My beam has a slat screwed to it with holes to make 6 loops.  I could not get them even.  I'm trying to find my copy of Joanne's book, it's around here somewhere....(it was a great help in getting this thing up and working)

ReedGuy

The cord is evened up when the tie on rod is brought up over the beam and then measure the ends between beam and rod. The cord is continuous so you just adjust it by pulling along the loops. Doesn't take very long.

kerstinfroberg

When Texsolv was invented, most (but not all) Swedish weaving teachers went from a continous cord to one (texsolv) cord per hole in the beam. No more adjusting! (But remember to take off the cords on the outsides if having a narrow warp - but that goes for continous cords, too)

ReedGuy

The Big Book uses one continuous cord, but do not mention removing the cord from the ends of the tie-on rod. But this is important. However, with separate cords I assume there is a groove in the beam to hold the cords attachment. :)

Instead of pulling the continuous cord out of the beam end holes just tie the ends of the cord onto a separate warp stick that is drawn taught to the warp and cloth rollers. Best to make holes to line up with the beam holes and use an arrow pin or steel pin would be stronger in the Texsolv button cord. That way it will lay flat to the beam and not be flippy. This is important because with no warp out on the ends of the tie on rods you get a bow. No counter tension on the rod ends. If your not comfortable with that idea, maybe use 3/8" or 5/16" round rod instead of the warp stick. My sticks are maple and the same thickness as Worst uses, so they will handle the tenson from the cord pulling. If that is troublesome, and the warp sticks need to be secured from being loose before tensioning the warp, just secure it with a wrap of texsolv on each end around the beam and secure with an arrow pin.

kerstinfroberg

Yes, ReedGuy, Lundell describes the continuous cord. The book was first printed in 1976 (ISBN 91-534-0388-6). (I have not studied later editions, so I can't say how much has been changed since the first edition.) Texsolv was founded in 1977.

To attach the separate texsolv cords to my old loom, I use the (original) holes in the beam(s) (my double warp beam attachment was bougth from AK ("Öxabäck") in about 1982):

When the cords are wrapped around the beam, they look like this:

As my beam has 5 holes, I have 5 cords "disturbing" the warp, instead of 8. For wider warps I haven't found the cords to be a problem (whether 5 or 8), but for narrow warps I sometimes do a "special". I have used separate cords on my main looms since I got the beams - and I still use the very same cords. As far as I can see, they have not stretched, even though I often take the outer two off the rod.

Some people take new technology to heart, if they think it useful - for instance, my grandmother got a sewing machine as soon as she could afford one (she was a tailor). I do know Lundell loved the way Texsolv simplified things, even if I do not know whether she changed  her looms this way.

sequel (not verified)

The problem with long continuous cords is they have to be adjusted before they wrap around the beam and overlap one another.  I use Texsolv now and when I get the rod straight, I mark the rod holes with permanent marker.  That way when I drop the end cords for a narrow warp I know right where to put the rod next time I use them.

ReedGuy

I have the 2008 version of her book.

For some reason I don't find it a real issue. Done properlly, the continuous cord does not overlap anywhere on the beam. What you see in the photo is not how the tie on rod rests for slipping on the warp. Instead of resting on the roller there, it is slung up over the cross beam from the back side. The loops are V shaped and narrow in as you wind and come to the rod. How can it overlap? It's obsolutely, positively not overlapped. I place warp sticks on each face of the octagon beam on the first rotation of warp.  There is no cord touching warp on the warp roller. I'll leave it at that. :)

Sara von Tresckow

I currently use all three - apron, continuous cord and single cord on various looms. All work.

Just learn how to get the tieon bar even with whatever variation is used on the loom - and to even out the eventual bumps, simply insert a round of warp sticks when the cloth reaches the beam and all is even.

Submitted by sandra.eberhar… on