I have tried warping my Julia 8s countermarch loom several ways and it seems to me the only way to dress the loom, back to front, is to remove the 16 cords that go from the shafts to the lamms and raise the shafts to get to the back beam.

Here is what the loom looks like from top and bottom:

Am I missing something? I like to rough sley the reed and move my lease sticks to the other side of the reed.  The warp is weighted in front of the reed, goes through the reed and the lease sticks to the back beam.  I usually leave my lease sticks in while weaving.

I realize I can warp front to back but it is more difficult to reach the shafts from the back of the loom to thread them.  I prefer warping back to front but if I go over the top of the shafts, the warp would be divided in half by the cords hanging from the top jacks to the lamms.

Any thoughts, ideas, suggestions?

TIA, Claudia

Comments

Joanne Hall

Hi Claudia,

If you mark the holes in the cords which go to the lamms, it is easy to put the pins back in after you are finished warping.  Just use a felt tipped marker and put a small mark at the hole that you had the pin in. 

And if you return to weaving with just the front four shafts, it is very easy to remove the extra shafts and lamms.

Joanne

kerstinfroberg

My shafts are from Öxabäck, so they may be different - they have a hook in the bottom shaft bars. It is very easy to unhook the cord, and then use the shaft holders to get the shafts out of the way. If there are no hools, it would be a very small, very cheap and very easy adaption to put some in.

(BTW - my old weaving teachers would be shocked to hear that someone is trying to dress the loom w/o first stripping it down to the bare frame... once the cloth was cut off, *everything* - heddles, shafts, treadles - the lot - was to be taken out before starting something new. "It is the way it should be done"  If I do that myself? No way! I only take out the shafts I will not be using - I even let the lamms hang, unhooked, of course. And the unwanted treadle cords.)

Dawn McCarthy

You can still warp back to front and place a raddle on the back beam.  I actually run the warp chain with lease sticks in front of this setup and beam - this allows me to reach the handle to beam and to maintain tension.  Once beamed, remove the raddle and place the warp over the back beam.  

Dawn

Claudia Segal (not verified)

Thanks for confirming my assumption that I need to remove the cords that run to the lamms. I will mark them as you suggest Joanne and then remove the pegs until the warp is on the back beam. Kerstin, OMG, sstrip the loom completely after each project. Only if the previous warp was 10-12 yards and I produced many towels or table runners or napkins first. I do see some logic in it but it seems like a daunting task.. Climbing under the loom is becoming more challengin every year. I plan to enlist my friend's help in puttin the Julia on a table the next time I need to change the tie-up.

Claudia Segal (not verified)

Thanks for confirming my assumption that I need to remove the cords that run to the lamms. I will mark them as you suggest Joanne and then remove the pegs until the warp is on the back beam. Kerstin, OMG, sstrip the loom completely after each project. Only if the previous warp was 10-12 yards and I produced many towels or table runners or napkins first. I do see some logic in it but it seems like a daunting task.. Climbing under the loom is becoming more challengin every year. I plan to enlist my friend's help in puttin the Julia on a table the next time I need to change the tie-up.

Sara von Tresckow

Gee, I'm beaming 40 yards today and taking a break. 

In 30 plus years of weaving I have NEVER, repeat NEVER unhooked the lams to warp a countermarche loom.

YES, I split the warp chain in the center - or better yet - make TWO chains that are easier to handle (doing it today). I then run those two chains - either through the shafts or over the shafts depending on my mood. The raddle is clamped on the back of the loom - or in the case of the Julia, we mount the raddle to the front with clamps and put the lease sticks closer to the back beam. If you are using a raddle and lease sticks, a small split in the center is not at all a bad thing.

Warp chains should not be more than 10-12 inches of weaving width anyway - that way there are less tangles or other anomolies. Full width on a 48" loom by me takes 4 warp chains - wrapped around the breast beam instead of a trapeze.

Just in case the center cords are really that much of a problem, I sell a nice line of vertical CM looms.

Joanne Hall

Yes, it is possible to leave the lamms tied up.  If you do that, when you start to thread,  take some extra heddles and put them on the ends of the shafts, twisting them a number of times to shorten them.  This will take the tension off the heddles, so that the heddles will move more easily.  Otherwise, the weight of the treadles and lamms will pull on the heddles and tighten them.

It takes about the same time to do this as to take the pins out of the lamms.  So, I take the pins out when I want to move the position of the shafts for more comfortable threading.

Joanne

ReedGuy

I prefer to take my shafts to the back and thread heddles from my bench there. But that being said, my breast beam can be removed and set a chair in there and do as Sara suggests easily enough. However, I wouldn't want to be crowded or do a lot of long reaching. Too hard on the body. Always another way Claudia. Pick one and go with it. :)

sandra.eberhar…

I don't take anything off or disconnect anything. I use a large (3' X 24") roller attached to the ceiling as a trapeze or valet and run the warp over the top of the loom to the back.  When I warped a scandinavian-type loom without the trapeze, I put a beam across the upper side beams and used that as a trapeze.  I do take the breast beam off to thread.

Sandra

ReedGuy

I follow the "Big Book" procedure and take the shafts to the back with the support craddle and pins in place. This is done after the warp is beamed. I also use lease sticks secured to the back beam as the "Big Book" shows, which holds the threads with some tension and I find this method a lot more ergonomic. At the front you would have the cloth beam at your knees and be reaching too much. That just doesn't work for me. It takes me very little time to move shafts. I have 8 and so there are 8 upper lamm cords on the lower bars and 16 cords up at the jacks. I can't see ever changing my procedure in this. :)

Claudia I know you've mentioned about the time taken to tie up. I know we are not all as limber as we once were and it gets worst after 40. And believe me I get more excercise than most on this forum, so don't hold that totally against your physical abilities. I usually tie-up 64 cords within 2 hours. Now, at first no, because I learning. But the sooner I can get off the floor and upright the better, I can tell ya that. :)

Claudia Segal (not verified)

Yes, over 40 and then some and I find being on the floor for an hour is bad for my back, etc. Plus, my ribs are still healing. The Julia is a small countermarch. It's 26" wide and has a very small overall foot print. I can move the countermarch if I wanted but it's not necessary. It's easy to thread from back to front if I get the bench at the right height and take my time. It's not a race after all. I am creating a shawl for a friend and already missed Christmas so I don't have any deadlines. I appreciate all the suggestions. Especially Sara's idea about buying another loom. I did consider the Oxaback horizontal countermarch when I bought the Julia. Next time I warp, I am going to try going over the top of the shafts and placing one bout on each side. I usually wind in 2-3 bouts depending on the width of the warp. Sticking to 8-10" is a good rule of thumb. Thanks all for your thoughtful replies. This is why I love Weavolution. Claudia

Claudia Segal (not verified)

OK, I'm all set with the warping. I'm going to try Sara's suggestions and use Joanne's twisted heddle to take the pressure off. Now, about the heddles. I had to move lots of heddle to do this Atwater Bronson Lace pattern and while threading I keep finding heddles that are twisted in such a way that I have to remove the heddles and put them back on one at a time. How do you deal with this issue? I removed the heddles by tying twist ties on all four sections of the heddles and removing them in a group. How did they get so twisted in replacing them? I had 7 that had one twisted around them in such a way that I could not get it undone without removing the entire group Thanks, Claudia

ReedGuy

If the weaving doesn't go full width I just leave them alone on the shafts making sure I have some at the far edges for balance. We usually start to the right with threading, so I make sure I shove a bunch to the far right on each shaft, then draw out what I need as I go from the next bunches. There is a cord one ties to the shaft bars so heddles don't drop off the ends.

Anyway, removing and replacing heddles is bound to cause errors, it just happens. Without rethreading a bunch of heddles because one is out of whack just make a substitute in it's place as the "Big Book of Weaving" suggests with some fish yarn. it will work just fine, wrap it around the bottom bar, even up the ends and then just make the eye at the same level as adjacent heddles with square knots at top and bottom of the eye and then tie off on the top bar. And carry on. :)

cottageweaver (not verified)

Twist ties are awkward with heddles. The method I learned from Becky Ashenden (and Joanne may very well use a similar method) is to take a sturdy string and use a figure eight to tie the bundles. You go through a set of heddles above the eye (loop twice), then cross over the strings in front of the eyes and down to the bottom loops, loop twice and tie with a bow. It's quick and easier than my description sounds! This way, they stay oriented correctly between top and bottom sets of loops.

This may be in the mini-movies on VavStuga's website. Joanne, is this is one of your books or your website? I routinely add and remove cut Texsolv heddles (sometimes hundreds at at time!) with no problems putting on, removing or storing. You can even loop a group consisting of heddles on different shafts - love those open shaft bars! With cut Texsolv heddles, you can easily move them around to different shafts or insert a new heddle in to repair warping errors.

Joanne's triangular wooden storage hangers are great for any stray ones that I have, then I tie them up when I have enough for a bundle....Toni

ReedGuy

I doubt any system is perfect, some are just lucky. :)

Submitted by Anonymous (not verified) on