Hello Everyone,

 

I need som help super fast. I am currently weaving a double cloth lambswool on my Louet Megado loom. I have set up exactly like the numerous times before without tension i.e no one helping by holding onto the warp as i wind on. I have woven 6cm and as soon as i wind the warp forward all tension has gone the worse i have ever experince accross one of the warps. I have tried everything but i don't know what to do.

I fear it is because it is too long a warp- 10 metres and that i should have found someone to assist me as i wound on. I've tried stuffing further the worse areas with weights etc but it will take me forever. OR the idea of winding the entire warp forward onto the front beam and then wind it back again.

 

I have 2 weeks to weave three 2m throws so I'm am very panicked that this long and wide warp has been for nothing and i will miss my deadline!

 

Please help any advice would be much apreciated!

Comments

laurafry

I rather suspect that beaming without any tension is part of your problem.  What did you use between the warp layers?  Can you find someone, maybe two, to help you re-beam the warp?  Another option is to weight the warp with something - I use jugs of water, one per 12 to 15 inch width of warp - as it is rolled on.

cheers,

Laura

Joanne Hall

I agree with Laura, re-beaming is a good idea.  I assume that the warp is wide and it can then be hard for even two helpers to hold and wind on with an even tension.  When you re-beam, perhaps you can pull the warp out beyond the breast beam, put a wooden pole inside  the warp to hold it flat and parallel to the loom and then put the warp and the pole on a towel on the floor and put weights on each end of the pole.  Then you will be winding on with some weight and the pole will hold the warp straight.  Good luck.

Joanne 

Fabienne from …

Thanks Laura and Joanne. As I feared then, I need to re-beam. I don't want to re-thread so my thoughts are cut and them to wind the second warp (which has bad tension) all the way to the front and then use tension via a team of helpers as we rewind it back. Ive used newspaper as I have ran out of wallpaper. I always find newspaper harder to work with, I will get some more wallpaper to use when I do it again.

Joanne Hall

I suggest that you get warp sticks.  You can order them where you get weaving supplies.  You have a double thick warp and a long one, so you need a perfectly wound warp.  Newspaper will not help much.  And wall paper is probably not wide enough.  The warp is wide, so you need sticks which are the full width of your loom.

Joanne

Fabienne from …

i have some warp sticks which i got when i bought the loom but have never needed them or used them before. I will do a bit of digging on the interenet on how to use them, but any tips would be apreciated.

Cat Brysch

heavy "craft" paper that you roll along with every inch of warp. I get mine at Home Depot in the paint section...it's the paper that painters put down on floors to keep the floor/carpet clean while they paint. You can choose the 36" wide roll, cut it whatever width your project requires and then, with every piece of paper rolled on, you can count one yard. This paper is quite heavy and sturdy and I use it on all 9 looms.

Try not to be nervous as it will only slow you down and take away the FUN! Good Luck!

laurafry

There are a variety of things that can be used.  The thing is to have something heavy/thick enough to prevent upper layers from cutting down into the lower layers.  Warp sticks, thick wall paper, corrugated paper or my personal favourite - bamboo blinds with the hardware removed - all can work quite well.

On shorter warps beaming isn't quite so critical, but the longer and wider you go the more important (imho) it is to beam with tension and use warp packing unless you are using warp flanges.  And then good tension is even more important.

Remember that a thread under tension is a thread under control.  :^)

cheers,

Laura

Dawn McCarthy

I find sticks really are best especially to assist with selvedge tension.  If I cannot recruit a "warping" helper then I attach free weights with s hooks.  On a long warp beamed with poor tension the problem will just continue and make it a frustrating and time consuming project.

Dawn

 

Submitted by Fabienne from … on