Most often, I use a HW magazine project, and follow directions carefully (my best talent).  I decided to branch out on my own and completed a plaid wool scarf without a published pattern; I used the following knitting yarns (those are strips of t-shirts for fringe spacers) on my 8H Schacht Mighty Wolf:

dark blue tweed - Tahki Yarns - Tara Tweed (80% wool; 20% nylon) - 1115ypp

light blue - Brown Sheep Company - Lanaloft Sports Weight (100% wool; "mothproofed") - 1326ypp

The scarf is a simple tabby, sett at 10epi with approximately 10ppi.  On loom, the scarf (under tension) measured 80.5" and it was 9.0" in the reed.  Off loom, it measures 76.5" (5% dimensional loss) and 8.2" (8.9% dimensional loss).  I do have 3 inches of a "sample" at the beginning of the project.  Sample and scarf were both hemstitched at each end.  I plan to ply the fringe (before wet finishing) - 4 ends (2x2) per bundle, and I did use 4 ends per hemstitched group.  At the moment, I'm not sure how long the fringe should be after wet finishing

Now, I'm very nervous about wet finishing.  I do have a new top-loader (Whirlpool Cabrio), but I can control water height and spin (since water is softened, I will use HE detergent).  I would be very grateful for advice/suggestions on the wet finishing process for this scarf, as I am rather nervous about how it will finish (there is about an 1/8th inch more draw-in where I used the dark tweed in sections of the weft).  MANY thanks in advance.

Pat

Comments

laurafry

Just finish your scarf the way your want it, draw some warm water in a basin with a little soap or detergent, swish it around gently, squeeze the water out and lay flat to dry.  If you want to give it a hard press, do that before it dries completely.  Trim the fringe evenly and you're done.

cheers,

Laura

patweaves

Thanks, Laura!  I was curious to try my new Cabrio washer for wet finishing... but do you think I should defer that to another project and use a basin for the scarf?  (I specifically wanted a top-loader to use for wet finishing.)

Oh... the hard press... will I end up with a sheen (these wools have a rather dull finish at the moment)?

Grethe

Sampling is brilliant. You can try different treatment whit your samples.

I will never use my washingmachine on a project, if I'm not sure what will happens.

So.. In the bassin as Laura said and next time you have to make a bigger sample (than the 3 inch) and then you can play and find the right finish mode.

Go for it. It looks great.

janenedriscoll

With the Lanoloft scarf, I would certainly hand wash it to finish it.  I often use shampoo when washing wools.  After rinsing, I sometimes put the item in my front loading machine on spin and spin it for 3 minutes or so, which helps in removing excess water.  I like to take the fringe spacers out after washing the scarf, but before letting it dry.  That way you don't get a wavy fringe. When it dries I cut it off at the heading with a rotary cutter, which help make the fringe more even than with a scissors.  

Good luck and the scarf looks beautiful!  I'd like to see a photo of the scarf after it's been washed.  I'm wondering if you see any difference in texture/shrinkage between the two different yarn types.

patweaves

Thanks, Jane...  I mentioned detergent (rather than shampoo), since I understood from Laura Fry (in another context) to use detergent for wool if water is soft (and soap/shampoo if water is hard).  I may try a minute or two with the delicate spin cycle (I like that idea!)... and that way I may as well use the washer (filled first with water and soap/detergent before I add the web).  I can then hand manipulate it in and out of the wash (very warm) and rinse (cold) waters... just as though it's a basin.

Since I want to ply the fringe, I will twist before wet finishing and leave excess below the knot, so I can trim the frizzy/wavy stuff after drying.

laurafry

Um - hard water requires some sort of detergent - shampoo fits in that category.  Soft water you can use soap.

With just one item to wet finish, it's just as easy to do it in the basin, especially if you are new to doing this.  You can control the results much better by hand than in the machine.  As Grethe says, you really need to 'sample' your washing machine to see how it is going to do the job.  Since the yarn is new and so is the washing machine, hand wet finishing is the way to go imho.....

cheers,

Laura

Su Butler

You want to be careful about using your Cabrio for wet finishing handwovens.  I have had one for a few years and the spin cycles can cause permanent wrinkles in the cloth.  Fulling/felting of wool does not work very well in these machines as they cycle water instead of letting the item bathe and agitate in it.  You can use the soak cycle, but once you start agitation, the water will drain out of the machine, defeating the purpose.  I would second Laura's method, especially for the yarns you mentioned using.  You can use your wool cycle on your Cabrio for washing the items after initial wet finishing.  It works extremely well.  I wash my husbands 100% wool sweaters in that cycle with no ill effects.  I do use warm water, but a very gentle spin cycle.

Hope that helps...

Su :-)

patweaves

Oh, my, Laura... thank you for the correction about soap v detergent (since I had it totally backwards - PLUS my erroneous understanding of shampoo).

So, for soft water, what is an example of a product that work best for soap?

laurafry

For soft water you can use either soap or detergent. Choose a product without whiteness, brightness and perfumes. If the product advertises that your textiles will be 'whiter than white' or smell like flowers, leave it on the shelf. Cheers Laura

patweaves

Thanks, Su, for the heads-up on the Cabrio.  I can see where the high spin cycle would leave permanent creases.  I haven't really examined the effect of the slow spin... will have to try slow spin on the next laundry load and see what the effect is.

My machine (one year old) is middle of the line (5600 model)... so no wool cycle, per se.  I did not intend to use the soak cycle since it does have the funky agitation process.  I believe I can soak by turning off the machine after filling the washer on the Bulky cycle (highest water level).  Then, I can use the Drain & Spin cycle (selecting "low" spin) - and pressing the "Start/Pause" button after a minute or so of spinning.  That was my thought process on the machine.

Clearly, advice here would be well taken for me to simply use a basin, as Laura recommends, squeeze out between towels, and lay flat to dry.

Most interesting thread - thanks to all for your thoughts! 

patweaves

Thanks again, Laura... good to know for my soft water that I can still use detergent (I've always been a fan of the Free & Clear Tide and All products - no dyes or perfumes!).  I just wasn't sure what product to use that was truly a soap and not a detergent. 

Sara von Tresckow

Good heavens. Keep Lanaloft away from any washing machine. This is a delicious springy soft wool that blooms in handwashing and would felt in a hearteat. It certainly doesn't any one's social status harm to do something carefully by hand.

If you don't use much washing agent you don't need to worry that much about what you're using. The detergent or shampoo are just to make the water slippery and to aid in rinsing any dirt or oils from the yarn. You certainly don't need to have it frothy with foam.

The less detergent you use, the less you need to rinse.

This wet finishing is like when you knit a sweater - you need to wet it and block it into shape to have the stitches bloom.

patweaves

Thanks, Sara... I definitely plan to handwash carefully... with just a few drops of the clear Tide (moderately warm wash water, swishing with no soaking, cold rinse, squeezing carefully, towel to roll out excess water - no machine spinning, lay flat to dry).

The washing machine discussion proved enlightening for future weaving projects... hence the continued questions.  This new machine has been fine for laundry (but I do miss my old Maytag with a real agitator!), but is still a bit of a mystery to me.

Sara von Tresckow

Just FYI - that real agitator is death to fine fabrics. The newer washing systems are much kinder on the cloth. The agitator really rubs holes in things, yanks yardage and tablecloths out of shape and isn't a good idea for fabric you've created on a loom.

 

samuelr

I think agreeing with Laura would be the right opion. Since you are so worried about getting this piece right, just do the wet finidhing in the basin, and try the top loader in machine , the next time. Or if you reallyy want to try the machine way, then go for it...and prepare a newer and better piece next time!

______________________

addi turbo knitting needles

patweaves

Well, life and holidays have gotten in the way.... but I finally wet finished (in the basin) and trimmed the fringe.  Before I ship it off to its intended recipient, I recall Janene's request for a photo (and yes, Sara, it is lovely and soft!).  Here 'tis:

laurafry

Very nice.  Well done.  :)

cheers,

Laura

patweaves

I appreciate the kind words... stay warm up there in snowy, frozen BC!  No white Christmas here in Tucson... but the dry air sure makes for a quick air dry of handwovens!  :)

laurafry

Yes, it's pretty arid here right now with the cold weather!  My warps are misbehaving - static electricity building up as I wind them on the warping board.  :}

cheers,

Laura

wevrldy

I have the same type of washing machine and can't control the water levels, as well as prefilling the tub.  I have done as Laura suggests, using a a basin.  A final spin cycle might be available on your machine, but I've had great results with the usual methods of rolling the scarf in a towel and then drying flat.  Good luck!  You've made a lovely scarf!

 

endorph

turned out great - I love the colors!

janenedriscoll

Thanks for the photo, lovely colors and a lucky recipient . Janene
Submitted by patweaves on