I just received my first Toika temple (small 8-11"), but I'm not sure about how to correctly place it near the fell. [I do understand how to correctly set the length of the temple by turning it upside down and holding it against the warp in the reed - then setting the pin so the selvedges are positioned at the base of the temple teeth on each side.]

My question really apples only to metal (not wood) temples. The metal arm ends in the middle of each "head" (which contain the teeth). When the arms are locked together and parallel to the fell, one head/end is closer to the fell (by several picks) than the other end (ie, they are offset). Is the goal to have the arms parallel to the fell? Or should the head/end be the same distance from the fell at both ends (resulting in the arms no longer parallel to the fell)?

To clarify, if If I set BOTH the LEFT and the RIGHT ends of the Toika temple 1/8th inch from the last pick thrown, then the metal arms (which are clamped together in the middle) are no longer parallel to the fell. This doesn't happen with a wooden temple, only the metal Toika (by virtue of its design). Is the fact that BOTH ends are EACH within 1/8th inch from the fell the important factor in placement - or is it that the arms should be parallel to the fell (causing one end to be further away from the fell than the other end)?

 

 

 

Comments

MaryMartha

I go with the one on the left. Now watch some expert tell us its all wrong.

Joanne Hall

It really does not matter, as the difference is only slight.  On a wide warp, you probably wouldn't even notice.

But, with a metal temple, I would not put it so close to the fell line.  The teeth of a metal temple point down below the temple and your beater may get scratched if you put it really close to the fell line.  And always advance the temple before you advance the warp, so that the temple will never sit above the breast beam and scratch it.  Not that you are a beginner, but when I am teaching, I always recommend the wooden temples to beginners so that they won't scratch their looms.

Joanne

patweaves

Joanne, thanks for the quick response... I assumed it was not a problem, since (after extensive Googling) I could not find any discussions/information about the issue.  But, I'm a bit of stickler and really wanted to know... guess my "OCD" is showing!  :)  (I'm the type that reads instruction manuals! )  Your advice about temple placement is well taken - however, the design of my Mighty Wolf (with the height of the breast beam) appears to take into account the position of the temple teeth vis-a-vis the beater race (see photo) - so I'm "good to go"!   Pat 

ReedGuy

I make really wide blankets so I have to use one. And, depending on your loom you have to be wary about where it is placed. Advancing the temple before the warp is very good advice. It helps guage how far you advance so you wont scrath the beam or maybe the race as well. I have been doing it a little differently and have come accustomed at how far to advance the warp. But Joanne's way is better.

sally orgren

I have the same brand of temple, and glad you noticed that it rises above the beater when the fell line is in the correct position. (I would have posted the same photo you did, and I have a different brand of jack loom.)

However, through inattention or hard beating, you can still scratch your beam. If that is a concern, I suggest sliding the plastic tubes back over the teeth once it is in position. This doesn't take all that much longer to do. 

Also, my habit is to align the heads to be about the same distance from the fell line, I do not worry if the bar is parallel to the fell line or not. It looks odd, but weaves perfectly fine. 

I use a temple at least 50% of the time, and find it especially useful at the beginning of wide warps in finer threads to establish a solid fell. After the first yard, I may stop using it, it just depends on the project.

Excellent question, and you are definitely on the way to becoming a great weaver! It's been my experience the really good weavers actually think about these kind of details and care about their results.

Submitted by patweaves on