I am a new AVL PDL owner and would like some expert advice on what adjustments I can make to create a larger weaving shed. I have a 60" loom with a fly shuttle and I can't get the fly shuttle to work properly because the shed needs to be a bit bigger. This loom sat in storage for over 13 years and I have been painstakenly putting it back together after I purchased it 10 months ago. I am finally able to weave with the loom and am really loving it so far. I just need help with what to adjust to get a larger shed. I would love to use the fly shuttle when weaving!

Comments

Dawn McCarthy

Do you have the manual?  The shed should never be huge - but enough to pass an AVL flyshuttle through.  The turnbuckles from the dobby to the treadles can be adjusted, also re-hook the springs to the lower jacks a little tighter.  Remember, the AVl has a small area from beater/fell to shafts - I assume as most of the PDL's are built to utilize auto warp advance.  If I can find the pages that address this I can email them to you.  I find I advance frequently or use the auto advance - as soon as the fell line gets to a certain point the shuttle gets stuck so advance often.

If you set the loom up without a manual it is possible the lower jack system is facing the wrong way, the lower jacks create an angle from the front to back of the shafts so that the back shafts have a decent shed.

Dawn

design2weave (not verified)

I do have the manual and have been using that to set up my loom.  The loom was in partially assembles sections (broken down for storage) when I purchased it.  I have a decent shed for weaving but it is a bit tight for the shuttle and it gets stuck in it when I try to use fly shuttle system.  I do have the auto advance and am using that set to the correct ppi I am weaving.  I did adjust the turnbuckles a bit tighter, but that didn't make a difference.  The hooks on the springs for the jacks are hooked on the third link from the end. 

Maybe my lower jack system is facing the wrong way?  The angle on my lower jacks has the shorter ones closest to front with the longer ones towards back.  I can't seem to find a diagram for this in my manual and this part of the loom was already assembled and stored this way when we purchased the loom.  I would appreciate any help...you are an expert on AVLs and I really admire your weaving!

kerstinfroberg

- that is how they are on mine, too.

- interesting that your shed is too low for the flyshuttles - mine is ok for them, but too low for my usual (Swe) boat shuttles...

Good luck! (it took me a long time to accept that there is no "usual", meaning CM, way to adjust sheds :-)

design2weave (not verified)

So if my jacks are okay...are my fly shuttles are too big?  Is that at possibility?  Do I need to use special AVL shuttles?  I am just using the ones that came with my loom.  I did adjust the height of my beater so that the bottom warp threads in an open shed are resting on the base of the the reed so that the shuttle can ride over top without issue.  I can weave just fine but would really like to use the fly shuttle...just for FUN! And, I know it will be a necessity on future wide warps.  My loom is 60" and a 16 harness.   I am really loving this loom!

danteen (not verified)

I have a fly shuttle on my AVL PDL.  I have their brand of fly shuttle and they are 1- 7/16" tall  (thick?).   Is that the size of yours?  

I have to adjust my beater, sometimes, also, to make sure that the shed floor is on the race when the beater is in the resting position.  My  spring chains have always been on the last link.  Not quite as tight as yours.

Hope you get a solution.  Goes much faster with a fly shuttle and less sore shoulders if you are weaving wide.

Teena Tuenge 

design2weave (not verified)

My fly shuttle is an AVL shuttle and it is the same height...1-7/16" tall.

I did adjust the spring chains to the last link, but that made no difference in the size of the shed as I expected.  I think those are adjusted more for the return of the jacks.  And, my beater height was adjusted early on so that the shed floor rests on the race, I just didn't know to call it that.

Here is a picture of my shed so you can see the tight space I have for the shuttle.  I am also attaching a picture of my jacks taken from the front of my loom.  Longer jacks are to the back of the loom.

Dawn McCarthy

The AVL flyshuttle is a little less than 1.5 inches high.  In the manual it says:

Adjusting the Turnbuckle: The purpose of the turnbuckle is that it provides a way to adjust the treadle travel so that you get a full shed.....

When adjusted properly the right treadle should stop aprox 1" from the floor on it's down swing and 1/2 inch from the cable pulley on its upswing.

Is your beater set in the middle for underslung?  Do you have lease sticks too close to the back of the shafts?  The height of the AVL shed is not too adjustable so it may be something else?  When the beater pushed back ready for shed to open, how much space from beater to fell line?  There should be a slight dip in the warp at the shafts.  I took some pics if that helps:

Having a problem loading - email me and I will send.

Dawn

 

kerstinfroberg

as usual, I'm making assumptions - mea culpa. I should have said: I have an overhead beater (same as I have on my other (CM) looms). For the shuttle to pass unhindered theought the shed, I have to hold the beater at the back position. (This comes naturally to me, the Swe CM weaver...)

Currently I'm weaving s&w, and am having (also "as usual") problems getting the number of picks per cm that I want. My usual CM solution is to crank up the tension. This does not work on the PDL (or I'm doing it wrong). I do have an auto-advance, new style. Thus, for this warp, I have the a-a set to achieve what I hope for - which means I have to, occasionally, advance the warp by hand. I can easily determine when a hand-operated advance is to be done by the fact that the shuttle(s) start to stop, stick, slow down (whatever) before they go all the way - the decerasing shed makes more friction than they can take. (By this I'm trying to say the same as Dawn, above: the PDL has a very short "sweet spot" - )

The only way I can think of to get a taller shed is to shorten the cord of the turnbuckle (I'm sure ther is a correct name for it, somewhere) - or, maybe, the treadle cord?

Dawn McCarthy

Kerstin - that was my conclusion also - but it looks from the pic it needs more than that - the turnbuckle adjustment is small.  On my AVL the warp is held down ever so slightly by the weight of the shafts, so it makes a very soft V from the side view (my cm is a straight shot thru).  If the beater is too high it will in fact limit the shed even though theoretically it is giving a sound floor for the shuttle. There is so little adjustment available on the PDL's that it looks to me like something else needs adjusting also!  From the pic the warp seems to take a downward angle from the race toward the front beam (not sure if this is just the angle of the picture or not).  If you loosen the warp and tighten the springs therefore pulling down the shafts a little - this will give that extra fraction so when the shafts are raised there is a little more room.  Hard to explain, I'm not an expert but I have owned several AVL's and I have never had an issue with the shed even with a flyshuttle.  We'll all figure it out! Might take more shots of the rest of the loom though!

Dawn

Dawn McCarthy

BTW is it an overhead beater or underslung? (sorry if you mentioned this already, I'm getting ready to go off to work and didn't re-read!

Dawn

design2weave (not verified)

Dawn and Kerstin, your suggestions worked!!!! Thank you! I backed off the tension by moving the weight up a bit and tightening the cord to the spring on the weight arm. I also went back under the loom and tightened the jack springs back to where they were. I had previously tightened the turnbuckle as well to make the cord to the treddle as short as possible. All of these adjustments yielded a shed just big enough to allow my fly shuttle to pass cleanly through without getting hung up!!!! Now, I just need to figure out how to make it fly a bit more...it is kind of slow and doesn't quite reach the other end, so I am thinking I just need more tension in the cord that sends it on its merry way. I have really noticed that there is that sweet spot that you have both talked about with the AVL and it has taken me quite awhile to adjust the auto advance to where it is maintaining the fell line in a good spot. I may have to make minor hand advances to maintain it like Kerstin suggested. I also have a glimakra loom and I hold the beater back while passing a shuttle in the open shed. I guess I have been doing the same on the AVL out of habit. My AVL has an overhead beater and I might take a harder look at the height of that tomorrow to see if I have raised it a bit too much. My warp looks level going through the heddles but the bottom of the shed does dip when opened. For now, I am so thankful for the pictures you posted on your blog and the expert advice you have all provided! Thank you from the bottom of my heart!!!! I am in good company!

Dawn McCarthy

Yeeaaah!!! Glad you figured it out! Now you know a whole lot more about your loom and also have it fine tuned!  Adjusting the cord on the flybox helps, the wider the width of cloth it takes a good smack!  Sometimes waxing the shuttle helps.

Congrats

Dawn

Bonnie Inouye (not verified)

The length of the cord on the flyshuttle can make a difference in how comfortable it feels on a long warp.

Feel the shuttle race to check for rough spots- wax is helpful, as Dawn said. If the shuttle tends to slow down or veer off-course in one place, check the reed. Bent metal parts in a reed can impede the shuttle.

The purpose of those springs underneath the shafts is not just to return them. If you have them just right, there is some work involved raising shafts at first and then it gets easier and you can hold the shed open without much effort. If the springs under the loom are too tight, it makes it harder to treadle. There is no reason for those springs to be totally parallel to the floor. I usually tighten the springs on the first two shafts with summer and winter because half the heddles are on those two shafts. Then I have two shafts with springs almost parallel to the floor.

We have a Weavolution Group for AVL users. Join the group and see what has been discussed so far.

Bonnie

TinaHilton (not verified)

When I bought my AVL, the previous owner said to always have the beater hit the bumpers on the frame.  That way you know you're getting the ppi that was set on the auto-advance.  When I tried to attach a rotary temple to my loom, it moved the fell line closer to the shafts and then my shed was too small. 

I have an underslung beater, if that makes a difference.  I can imagine the beat wouldn't be as even if I didn't beat against the bumper.

design2weave (not verified)

Weaving is going great and I am nearly finished with my scarves out of 10/2 hand dyed tencel. The fly shuttle is working great after some paste wax which has really made it FLY!!!! I have to manually advance a couple of clicks when I start to notice the beater not hitting the bumpers, but other than that, I am LOVING this loom!!!!! Keeping the fell line in that sweet spot makes all the difference. Thanks for all the advice and help!
Submitted by Anonymous (not verified) on