Hi,

I would like adivce or suggestions on how to best wind a random multicolor warp. my current method is to run about 4 strands between my fingers and go back and forth on my approx 9yd warping board. I change colors when I come to the end. I tie a string around each section and chain the warp to keep from tangling.

my problem is when I'm winding the warp on to my loom (I go fron to back through lease sticks, through the reed and then the heddles and finally winding onto the back beam. It seems as hard as I try the for strands of warp still are tangled. I think it has to do with how difficult it is to run the strands through my fingers as I wind the warp on the board. is there a tool that I can use instead of my fingers to keep it less tangled?

any suggestions welcome.

thanks

Nancy

Comments

Liese (not verified)

Hi Nancy you need to make yourself a warping "paddle".  I cut a long oval out of plastic from a food container, punched holes with a knitting needle putting 2 holes on one end and 2 holes on the other so I can hold the piece in the center. You'll be making a 4 thread cross. this helps keep the threads from tangling as they come up through the 6 dpi reed with the cones underneath. You may have to experiment with how long to make your oval.  You might look at Peg Osterkamp's website to see if she has some info there too.

ReedGuy

The paddle could help, but make sure you have lots of ties on each bout to keep threads from crossing. I made a rather simple paddle when building my loom last winter, taken from Edward Worst's book, only I added some scrap walnut for the handle. I intend to use it on fine polyster some time soon as I'm sampling some for liner fabric.

nancyjpwilson (not verified)

thanks for the responses. thats kind of what I thought I needed to do. nice to know I can make one and see if it solves my problem.

tess1956 (not verified)

You can also clamp a small reed to the bottom of your warping board and run the yarns through the dents to keep them separated while you use both hands to warp your board. This is what I do.

ilovefiber

Oh, where were you with this suggestion about the reed when I needed it???     Great idea.  May have to try it if I ever do a 4-color warp again.  Thanks!  

nancyjpwilson (not verified)

that is an interesting idea. Do you have a photo that shows more of the overall set up? I'm not picturing how it would clamp to the warping board.thanks so much for the suggestion.

tess1956 (not verified)

I'm new at posting here and find it difficult. I have no idea if you can move the pictures around so you can see it all, nor do I know how to resize, but see if this makes more sense,.

 

ReedGuy

I'm not sure that really solves the problem entirely. Still have to make sure the cross is not twisted on the return path to the tie-on peg. A regular spool rack made of dowel and eye hooks will do the same as pictured. Sit the spools on over the dowels and thread through the eye hooks. A paddle, like your figures, keeps the order at the front ends of the yarn, not the rear and keeps from twisting as you measure off the warp. The turn at the cross is a figure 8, but no twist as you return to the tie-on peg at the start.

tess1956 (not verified)

The reed holds the yarns and allows me both hands to make sure the yarn is wound perfectly, and that the inside thread doesn't end up on the outside. But every person has to find what works for them. I have rheumatoid arthritis and this is what works for me on mixed warps.

ReedGuy

I usually do 4 ends at a time in my right hand on a warp reel. The left hand turns the reel. I will be using the paddle for the polyster because it is so fine. I don't like being cut by the stuff. ;)

nancyjpwilson (not verified)

thanks Tess. the pictures do help me understand how you do it. I use a warping board, not a reel, so I'll use this info to rig up my own set up.

thanks again for everyone's input

Nancy

Joanne Hall

I wind my warps with mulitple ends.  This makes the warping, especially the beaming go better.  Mulitple ends eliminate the tangling.  However, in my teaching, I often demonstrate on a warping frame as that is what the students have.  I use a reel.  Reed guy is right.  It is best (easier, and faster) to use a reel.  It also keeps the warp threads straight and not twisted.  When I demonstrate on the warping frame, it is hard to keep the threads lined up straight.  One naturally twists your hand when going around a dowel. 

But, remember a little twisting back and forth will get straightened out when you chain your warp. You really do not have a twist in the warp.  You would have to turn a summer salt to do that.

Also remember that when winding with more than one thread, there is always a twist at the ends, both the end dowel and the turning dowel at the cross, as you go around them.  This is just part of winding more than one thread at a time.

Joanne

ReedGuy

My tie-on dowel is below, most begin at the top. I'm different. ;) So the hand position is opposite for those that begin up top.

You will have a twist on the tie-on dowel as you return each time. Doesn't matter, those ends are cut to tie on the cloth beam rod at the end of warping. When you begin, the palm faces outward with your ends between the fingers (4). The lease end has no twist other then as your making the turn around the last corner of the reel to the lease pegs. So as you come to the first lease dowel your palm goes from facing out to facing down as you go over it. The palm is facing down as you go under the next and over the third. Then begin spinning the reel as you return and palm now faces up and go back over the middle dowel and under the first. Then as you pass by the first peg and make the corner your palm faces inward all the way back around to the tie-on dowel as your turning the reel. When at the tie-on dowel again, you twist as you return to the lease pegs. The "Big Book of Weaving" illustrates it quite well, that's where I picked it up. But as I said I start below. Takes a small bit of practice, then you've mastered it. :)

I find finer yarns need more ties on the bouts and keep the bouts smaller. That's my rule and I'm stick'n too it. :D

nancyjpwilson (not verified)

well, I've looked on the internet for info on warping reels. saw a conversation on weavolution about making a reel, found the link to see the 1918 book with plans. I'm thinking I might purchase one instead of trying to talk my husband into making me one. any comments on the Leclerc table warping mill? seems like it would be nice to have on table top instead of on the floor. anyone have one and like or dislike it?

thanks

Cheryl M White

I frequently warp random warps, and I use a lot of variety in the yarn and the color.  I use a board, and I design on the board as I go.  I also warp back to front and don't have a lot of tension problems.  I like to get the warp wound on the beam and out of my way.  If there is a lot of variety in the yarns that I use (and I mix all kinds of fibers together), the ends that I tie on will sometimes have some difference in length, but I have done this for years with very few hiccups.  I don't think the wrapping around the dowels on the board makea that much twist, and as someone said there is some twist when you chain the warp.  The best bet is to find the way that works best for you and then perfect it.

Cheryl

ReedGuy

A agree with you folks. Do what works for you and makes you most comfortable doing it. I'm not pushing any method, just presenting the way I do it. But there is very little bending on a vertical mill and a hand is usually on it to turn it so a little steady support is gained. You might find leaning over a table top board could be strenuous if your lower back isn't in the best of shape. Try different ways, and go for it. :)

Submitted by Anonymous (not verified) on