Hi - I am a very new weaver.  Very.  I recently got a Nilus Artisat loom that had been in someone's barn for 30 years.  It cleaned up quite well, however the aprons were covered in rat....... - well, you get the picture.  I took them off to launder (disinfect!) and now am confused about how to get them back on.  This loom came with a front and a rear apron.  If anyone has photos showing how both these aprons attach, it would be greatly appreciated!  The Warp & Weave book (still somewhat intact after it's adventure) does not show a diagram.  I cannot find anything showing this on the Nilus website.  Help!

 

Comments

Bonnie Inouye (not verified)

I used a LeClerc Artisat loom from 1969 until 1994. I remember the aprons and think they were just tacked onto the wooden beam. Did not find photos on the LeClerc website so I searched for LeClerc Artisat apron. Camilla Valley sells replacement parts for LeClerc looms. Here's their description, which has a photo of the parts. Search more than one website when hunting for loom information.

These Aprons are attached to the warp (back) and cloth (front) beams of floor and some table looms. The warp threads are attached to these using the metal warp rod and they have been designed to be long enough to unwind around the loom breast beams to prevent the waste of warm. Made of heavy canvas, these aprons are hemmed all around to prevent fraying and have a sleeve at one side designed to fit a warp rod. Enough tacks to fasten the apron to the warp beam are provided for installation. Normally 2 aprons are required, one for each beam, except when a sectional warp beam is used. In this case, only one apron is used (on the cloth beam).

Frederika

Thanks Bonnie;

I did see this description on the Camilla Valley site.  I was hoping for photos, as they will make much more sense to a very visual person like me.  I was surprised that the LeClerc site didn't show them, nor did the book.

Thanks again.  This description will be invaluable when paired with photos.

 

 

r1mein54 (not verified)

Frederika, look at the beam and you should be able to locate the previous tack or staple holes that held the old apron canvas [may need to roll it some]. I believe what you want to know is that it lays out toward the breast beam and is tacked so that when it winds up the canvas the outer layer covers the tack line.

ReedGuy

Yeah not all websites present the finer details of their looms. One of the better sites is one that sells Swedish looms and the loom distributor is a member here who has written some of the finer details about their line of looms. It is surprising that Leclerc doesn't describe this canvas as part of a maintenance section of the book. I'm sure a call to Leclerc or Camilla Valley will yield some good information though. That option is always open. ;)

Joanne Hall

Thanks ReedGuy,

We don't have apron instructions on our website, but I have laundered a Leclerc apron, once some time ago, and it came out very wrinked and I could not flatten it well enough.  So, I just purchased new canvas material and used it.   The factory has in the past sent along a bag a small tacks to use.  So, you just use a hammer and small sharp tacks.  Just be very precise when you put it on.

Joanne

Frederika

Thanks to all! 

I ironed the aprons and they look nearly as good as new.  The tacks are an issue - I will go to the hardware store and look for some.  Will likely measure with a ruler and mark the area with a pencil- can see how it would be an issue if it weren't installed straight.

My problem is also that there are two aprons.  Both have metal rods that attach somewhere.  (I understand where they go in the apron, but not where they go afterward).  Thought having a photo would clear up the mystery. 

Of course, this is all like learning a new language - both fascinating and at times frustrating.  One reader did send a few photos that are helpful, at least for the apron that tacks on to the drum.

sequel (not verified)

The rod ends of the aprons are where the warp threads will be attached.  The un-rod ends are where the apron is fixed to the beam.  I find it helpful to tape the apron in place, then wind it up to make sure the apron and rods are square to the loom (rods parallel to the shafts and breast or back beams) before I tack them down.  I use small upholstery tacks or a heavy duty staple gun. 

Submitted by Frederika on