Hi,  I am new to Weavolution, and weaving, I live in Scotland.

I am hoping for some advice, if anyone  can spare the time.    I have just bought  a used 4 shaft floor loom.  It has 8 horizontal jacks, 4 treadles and 4 lamms. It came in kit form and with no instructions  for assembly.   Its previous owner purchased it as a working loom,  pre-loved 18 years ago , and never  completely assembled it.

  I realise that this is the worst scenario for  purchasing a loom.   But  overall it is in good condition, apart from the inevitable rust on the metal parts.   I appears to be homemade of pine, no warped pieces as far as I can tell, and has a 43 inch reed approx. 22 dent.  Overall dimensions are 53"w x 48"d x 58"h.   The shafts have Jones Textilaties Ltd. Blackburn, England printed on them, with metal heddles. ( I'm unable to find out very much about the company.)  .

My question is this,   is it a jack loom, or a countermarche ( which I thought had to have two sets of lamms i.e. 8 ), can a counterbalance loom have jacks?     I have looked at many photos of looms, and of plans for looms ,but cannot find anything that resembles this one.    I will try to post photos soon, but have not assembled the loom,  only propped up the pieces together,  to find out what goes where,  before I clean and refinish it.  It does not appear to have any pieces missing.............ie no extra holes for other pieces to be attached to. 

Any comments would be appreciated , although I realise without photos its a hard ask.

 

Comments

ReedGuy

Sounds like a horizontal countermarche, but that is just a guess. Others will likely know more. ;)

Claudia Segal (not verified)

Photos would make a big difference. There are several countermarch and counterbalance loom owners on Weavolution and we're all happy to help. It does sound like a horizontal countermarch with the jacks on the top. A counter balance does not have jacks but a countermarch should have 2 sets of lamms, you're right about that. If you need help posting photos, there are several articles and videos in the help section. Click on the word help on the black bar at the top of every page. Claudia

babagal

Thanks for your input,  will post photos .  Although  they only show the loom propped together,  so that I could check that all was there.  I  have photos that show the various elements of the loom which I will also post.

babagal

This is a view from the rear of the loom.

Close up of H-beam, showing lamm holding bolt.

H-beam with lamms attached.

I have 4 of the bottom shafts, and 2 of the top, but have only 4 treadles?

I am not sure these photos will help. It may be  better to fully assemble the loom and try to weave,  before making any decisions on modifications if any. I believe the loom is  homemade, to 'fit' the shafts, so it  will not necessarily  follow conventional loom plans.     Any suggestions welcome.  Thanks.

I've just re-read that last paragraph.............. I realise that I have no idea how to tie-up the loom using only 4 lamms.............. so  weavings out.....

My other half is a woodworker, so will be able to modify the loom for me.........regarding the second set of lamms,  am I right in thinking they should be longer than the uppermost set?  do they need to be attached to the opposite side of the loom?  ( I have discovered that there are 3 sets of holes in the H-beam  where the lamms are attached,  is this for adjustment or the other set of lamms?

I will do some more research regarding lamms etc.,  but all advice  gratefully received.

Thanks Claudia  for advice re posting images.

 

mrdubyah (not verified)

I think you have a counterbalance loom, although it may still be missing some parts.  Since there are no jacks, it can't work as either a jack or a countermarche.  I don't see any pulleys or horses, but I think I see dowels.  For an idea of how to set up a counterbalance harness using dowels, see the fifth picture down on this page:

http://www.camillavalleyfarm.com/weave/loomparts3.htm

You might also want to read up on counterbalance looms to see if that might be the answer. 

ReedGuy

The poster said there were 8 horozontal jacks. However I don't see any in the photos either. Unless I see some in the chair.

babagal

Yes there are some of the 8 jacks on the chair......I thought they seemed long.........but on the otherhand it is years since I  have seen a loom 'in the flesh'.   Some of the jacks have 3 holes , some 4 .  I have looked at the posted link to the dowels,  I havent got anything like that.......of course they may be missing..........but checked out the looms on the site...............my loom appears to be similar to a Colonial 1.......jack type......but with the lamm support of the  counterbalance..........ie not floating lamms but pivoted at one end.     Once I have made space and assembled it, I am  going  to tie up as the Colonial 1,  and see if it  weaves.    I am hoping that just because it is not standard, it  wont mean it doesnt work.    Once I discover the pitfalls of this set-up, I'll consider adding another set of lamms........but read somewhere that it will involve major mathematical calculations re length of lamms  to get it to  work..........

ReedGuy

It won't be that hard to make others, just copy from existing. Use a drill press for the holes. The thing is that the treadle holes and lamm holes should line up when suspended so there is no additional friction in the movement. Everything has to be relative to the centre of the loom.

babagal

Thanks,  I'll bear that in mind........it  will be other half who does the woodworking......but at least I'll be able to explain what it needs to be like.

mrdubyah (not verified)

Sorry, I didn't notice the jacks on the chair.  If you have jacks and only one set of lamms, then you must have a jack loom.  Jack looms don't need a second set of lamms because the unlifted frames are held in place by gravity  (although they sometimes have to be weighted to work effectively.)  Because of the high castle, it looks like this loom has overhead jacks that pull up on the frames rather than underframe jacks that push frames up. 

To assemble, (see below) put the jackbox on the top of the castle with a pin through the center hole of each jack so the jacks will pivot.  Tie a yolk between the two holes on the inside ends of each pair of jacks.  Then tie a cord from the center of each yolk to each lamm so the jacks rise when you pull the lamm down.  Tie cords from the outer holes on the jacks to the outside edges of the frames so that the frame rises when the jacks pivot.  Frames will return to rest position by gravity.  Hope this helps!

babagal

Thanks for everyones help.......I am still trying to find the space for the loom.....family /work taking priority at the moment.  Hope to get it all together when better weather arrives......aming to be weaving this summer.......at long last........

babagal

Thanks for everyones help.......I am still trying to find the space for the loom.....family /work taking priority at the moment.  Hope to get it all together when better weather arrives......aming to be weaving this summer.......at long last........

Joanne Hall

If picture three is the top of the loom and the pieces there are attached towards one side with a metal rod, then you may have a very, very old style of countermarch popular over 100 years ago.  Swedish weavers may be familiar with this.  The one disadvantage of this is that the movement of the jacks causes the shafts to move sideways a little with each change of the shed.  However, it is hard to see from the photo.  I may be completely wrong.  If that photo just has lamms sitting on it, then it is not what I have described.  But, I have seen this type of countermarch in old Swedish books and in photos of looms from about 1900.

Joanne

Submitted by babagal on