when not working on your project?  In my first weaving class we released the tension on the project before leaving for the night as our class was a weekly class.  However, on my loom at home if I am getting to the project the next day should I leave the project with the tension or should I release that as well? 

Thanks in advance!

Cheryl

Comments

kerstinfroberg

a one-time famous Swedish damask weaver, named Emma Wiklund (if memory serves) often told this: "I used always to release tension and take off the temple when going home for the day. When I went home to have my daughter, I forgot. When I came back 8 months later, I continued to weave where I left off. There was no mark, and I have never bothered to release tension since then."

Emma wove with linen in warp and weft, used a temple and high warp tension. She is now dead since 25-30 years. The anecdote was published in a magazine somewhere (maybe VÄV? maybe Hemslöjden?)

Joanne Hall

Thanks Kerstin for that story.  And I agree, I have left the loom without taking the tension off and leaving the temple on.  What is your experience with the AVL, which is a jack loom?

Here in the US, we have a lot of jack looms.  And I would release the tension if using a jack loom, since the heddles are metal and the shafts are heavy.  The metal heddles are pushing down on the warp.  However, one does not weave with a very tight tension on a jack loom, so perhaps it does not matter.

Joanne

SallyE (not verified)

I take the tension off if I remember.   My theory is, taking the tension off won't hurt anything.   Leaving it on might or might not cause a problem.  If I'm using an "iffy" thread for my warp, I do take it off.  For strong cotton or linen or silk, I don't think it matters.

kerstinfroberg

Joanne, since I now have the auto-advance, I would not dare to try to release tension... it may work. As it can be very tricky to re-set the fell to the exact spot after correcting mistakes, I have decided not to risk anything unless needed ;-)

laurafry

Like Kerstin I don't release the tension on my AVL, but do release it on my Leclerc Fanny (counter-balanced) loom.  Personal preference?

cheers,

Laura

Cheryl'B

I am using a Leclerc Jack and it makes sense if left under tension the heddles may pull on the warp.  I have enough issues being new to all this that creating problems for myself is not on my list of things to do.

I'm working on my first doubleweave project and wanted to make sure I wouldn't mess things up if I let up on the tension.  It's so much fun and this is a big accomplishment for me that I didn't want to ruin by making a simple mistake as to leave tension or not.

Sometimes I just need to know the why's of what I'm doing.

I really appreciate all of your input on this.

C

sally orgren

I am on a jack floor loom too, and I don't release the tension or remove the temple when I finish for the night. I tend to weave tighter setts and under higher tension than most of my guildmates. I have not encountered a problem, but usually return to my project within a day, and at most would leave it for a week or two. (Eek, never 8 months—not due to tension issues, but because I would miss weaving too much ;-)

I typically weave with cotton, tencel, and bamboo, with occasional forays into silk and linen, and alpaca will be up next. I am not very versed in wool, which may be more stretchy if left under tension or with weight on the warp? 

I think as a newbie weaver I was told to release the tension a bit when I finished weaving, so I suspect I may have developed a bad habit and just not suffered the consequences yet.

ReedGuy

I release tension, as I don't know when I may be back to the weave. It's not a big deal in the winter months because I will continue on the next day or two. I work mostly with wool. :)

mneligh

I release tension only when I think the warp might stretch, like with my handspun, which typically is softer than commercial.

fibrefun

I was taught to always release the tension, but when I forget, I haven't noticed a difference. So I have always wondered about how important it is to do this.

Guiding Myth (not verified)

All but one of my looms are Jack looms.  I don't release the tension on any of the looms.  Haven't noticed any difference even with delicate warps.  The only project I recall releasing the tension on was when I was weaving a weft faced rug years ago under high tension.  But that was more of a concern for the loom than the warp.

Usually AVL looms have texsolve heddles not metal heddles. I have not done any reseach on the subject but I would think that static tension on a warp thread created by a metal heddle would not be a problem when the loom is idle.  It seems like abrasion is the concerned.  Assuming, of course that the thread is strong enough to hold under tension and that the loom is warped with even tension - so that the tension is not being held by just a few threads.

Stephanie S

kerstinfroberg

(but it may be just a myth):

Someone had a sturdy linen rug warp on a sturdy old traditional ("barn"?) loom, under high tension. Left it tensioned - and one of the beams broke, supposedly due to changing humidity which made the warp "shrink".

(I still don't relelase tension... or, not often, anyway. All my beams still are whole.)

karentiede

1.  100 yd cotton poly warp.

2.  Irregular weaving schedule.

3.  Newcomb studio.

4.  Wide range of humidity in my house.

Sara von Tresckow

"Releasing the tension" means letting out a notch or two. Letting the warp relax might make it more prone to showing marks than leaving it under moderate tension.

I just completed a 10 yard wool rug warp put on after Albuquerque in 2010 - 6 rugs and 2 floor cushions later, without ever releasing the tension as I wanted the rugs to stay firm - no issues with either loom or warp or rugs.

Cheryl'B

I happen to weave with very high tension or the lower portion of the shed feels soggy (for lack of weaving terminiology knowledge) . I just wanted to make sure my warp would be okay. Thank you all for your useful information. C

ReedGuy

For me also it's just a couple teeth I let off. I do not make the warp real slack.

Cheryl M White

I used to release warp tension when I could not be sure my cats could be kept away from the loom!!.  Some of them just love to sleep on the warp and that is disastrous(as I found out very early in my weaving career).   Now I can run them out and close doors, but a cat keeping you company while weaving is a friend indeed.

Cheryl 

Cheryl'B

I have two of them, one is a kitten and he loves to sleep on the back beam when I have something warped.  He listens pretty good about the loom (to my surprise).  Or he sits on the castle and watches me.  Very cute indeed.

I only release tension ever so slightly, just in case.

Sara von Tresckow

If you are using a rising shed loom and your lower shed feels "soggy", it is a feature of the rising shed. No matter how high you crank your tension, when you raise only part of the warp threads, those left down are a little less under tension than those raised.

To combat a soggy lower shed, look into a counterbalance or countermarche loom.

Cheryl'B

I've only started weaving in May and thought it was something I was doing wrong........

I have a 4h Leclerc jack loom.  I am hopeful in the near future to purchase another loom because I feel the 4h limits me.  I will definitely take your suggestions into consideration on my next loom.  Looks like I have more research to do.

ReedGuy

I like cats, but they would not be allowed on furniture or looms. :D LOL

I knew a lady in her senior years who had cats and it was no surprise her cat might be found in the mixing bowl. hahaha

But, that is all I have to say about cats. ;)

Submitted by Cheryl'B on