I know I must have set my loom up wrongly but don't know how to adjust/what to adjust to sort it out. Wonder if someone could help. When I push down on treddle 1 the heddles rise but on treddle the second shaft they fall. IN fact they fall so much that when they rise, when I treddle 2 some of them are crossed which means they can't create a large enough gap for the shuttle. Help please Paul

Comments

Dawn McCarthy

Can you list more specifically how you have the treadles tied - T1 = shaft # T2 = shaft # and so on? T being the treadle.

Dawn

 

 

Joanne Hall

Photos would help.  Do you mean that warp threads are crossing each other? 

Joanne

ReedGuy

One question. Have you threaded heddles before? Looking from the front toward the back of the loom, the shafts are numbered 1...2....3......the furthest away being # 1 and in sequence toward you. The first heddle to thread depends on the weave. It could begin on shaft 1 (at the back) or the front most shaft. If you have 8 shafts, the front most is number 8. When threading, the warp threads can not cross one another.

paulz

This is the first time I have used the loom. In fact it is the first time I have even seen a floor loom let alone used one.There are six treddles. I have tied the back one (number 1) to the second treddle, number 2 to the 3rd treddle, no 3 to 4th and 4 to 5th. Was going to put 1 and three on 1st 2nd and 4th on 6th.

I have (as usual) tried the photos on this site but not managed it again so again I have put them on flickr.

http://www.flickr.com/photos/7866840@N07/

Sorry photos are in reverse order on flickr The first photo 318 shows the string heddles ligned up nicely. 2nd photo (319) shows heddle 2 (treddle 1 has been pressed). As you can see the middle ones are loose. 3rd photo 320 is when next treddle has been pressed and is the first bar with the heddles on. Next two shows the heddles on the heddle bar having crossed over.

MAny Thanks Paul

Sara von Tresckow

Paul,

You'll really need to make photos showing the entire setup - from the treadle to the lam to the shaft to the way the shaft is hung for us to be able to help you.

Laiila LUndell's "Big Book off Weaving" contains excellent illustrarions of how to set up a counterbalance loom.

ReedGuy

Do you have the centre hole of the lamms tied up to the lower shaft bars? Also, the treadle tie up holes line up vertical with the lamm holes. They can not be crossed. The number of lamms equals number of shafts. Sounds to me you have not tied up the central cords from the lamms to the shafts. The weight of the lamms holds the shafts taught with gravity as the horses hold them taught in the upperward direction. When tying up four shafts to the horses, one end of the horse (the outter most end) gets tied to shaft 1, then the other to shaft 2. On the far end, the opposing horse is tied the opposite way with the far end tied to shaft one and the inside end of the horse to shaft 2. (mirrored) Continue in this fashion for the next 2 shaft tie ups. You may not be ballancing your tie up. Did you use the shaft cradles, I see with the loom in one photo, to tie up the shafts level and even?

The photos posted concerning your troubles are of limited value, can't see much.

sandra.eberhar…

Paul, we need to see pictures of the entire loom at once.  When you only see a part of it, you can't tell what is going on with the treadles and lamms (I assume you have lamms because you have 6 treadles).  Counterbalance looms can take a little fiddling to get them working, but then they can be real workhorses; easy to treadle and simple to tie up.

sandra.eberhar…

One problem is your tie up.  I think you are tying your treadles directly to the harnesses with out using the lamms.  The lamms are the four pieces sticking out of the left side of the loom, in your photos they slant down to rest on the treadles.  Counterbalance loom are designed to raise two harness at a time.  The most common tie up is 1+2, 2+3, 3+4, 1+4 (2+4, 1+3).  The treadles in parenthesis give you plain weave.  You tie one harness to each lamm, then two lamms to each treadle.  Some looms will do one shaft at a time, but not all, and not very well.  what do you mean by "heddles have crossed over"?

ReedGuy

I think was is happening is he has not tied the upper and lower shaft bars properlly, so the heddles are not taught and are jumping over one another on some shafts.

paulz

Hooray. UP and weaving. Been about a month. Havent posted as cant add photos (still). Please look at them on my flickr page. Also is my new loom complete with weaving bench. This was from my local art and craft studio. Can anyone identify it? Also came with a couple of devices which I wouldlike to identify. Not good photos but maybe someone can help. Trouble is they are stucj in as I have very little space. MAny Thanks Paul

http://www.flickr.com/photos/7866840@N07/

laurafry

The wooden frame with the wire is most likely a 'lazy kate' - a device for holding spools horizontally so that they can turn and feed off for things like plying (spinning) or winding warps.

The round cage thingee looks like part of a squirrel cage swift for holding skeins of yarn so they can be put into balls or wound onto spools, bobbins etc.

cheers,

Laura

paulz

Yes it is a squirrel cage swift. The lazy kates I have seen have always been smaller. I guess they come in various sizes though. Many thanks for your help.

Paul

Woodburner

Did you figure out what the problem was or did you just redo something and it just came right? (As they do!)

paulz

 

The main thing was logial thinking. I thought that if the shed wasn't large enough for the shuttle then I needed to create more distance between the place where the weave gets beaten and the reed. This meant moving the heddles and the reed towards the back of the loom. Once I had done this I realised the reed needed lowering as the shed was being restricted by the top of the reed.

I then could weave a couple of rows and saw that the weave wasn't coming out properly. I could then see which wefts needed sorting.I also hadn't got the treadles in the correct place - thanks to the ladies from the local guild they helped me with this one.

Once this was done it was so smooth - despite some of the wool being quite hairy and too thick for the reed.

Thanks

Paul

Submitted by paulz on