Help! Does anyone know where I can find a linen mangle? 

Comments

Sara von Tresckow

The electrified cold mangles are no longer available in the US, though there are still some made in Europe.

You can easily make yourself a hand mangle that is quite effective.

You need a smooth round piece of wood 15 - 30" long and at least 3" in diameter for the mangle roll. Then you take a flat board about 4-5" wide, with or without a handle, with or withour carving or painting.

You roll the linen around the wooden roll with a cover cloth (old towel will do) to keep it clean, lay it on a flat surface and bear down on it with the flat board. You go back and forth on a diagonal - your body weight and the rolling motion is what makes the cloth flat and smooth.

This is more effective than the marble rolling pin that some recommend.

kerstinfroberg

Actually, it is better just to roll it "forth": roll in the same direction as you have rolled on your cloth - then slide the whole package back to where you started, roll again...

Going both directions will make the roll slightly looser with each "back", and can cause wrinkles in the inner layers.

Penn (not verified)

Forgive me if this offends the artisanal sensibilities of many here, but the process seems to require weight and pressure.  I saw a video of one of our prolific Weavo members doing this by hand, and was exhausted just watching her.  I have some physical limitations, and if I can conserve the kind of energy required by a procedure that necessitates brute force, I'll do it.

I look at the process described for cold mangling, and wonder whether a piece of fabric, laid on a cloth-protected sheet of 5/8" or 3/4" plywood, covered by fabric and a layer of heavy plastic, then slowly driven over repeatedly, wouldn't be successfully mangled. 

Also, I saw someone advertising a stationary ironer, like an Ironrite, as a mangler in the "For Sale" section.  I have an Ironrite that I was planning to sell on Craigslist, but will hang on to it if it actually can perform cold mangling, by rolling without the heat turned on, or at the lowest setting.

Thoughts?

laurafry

I've not used an Ironrite mangle to successfully cold mangle.  I've never been able to get sufficient pressure on the roller.  A marble rolling pin and pastry slab works wonderfully.  :)

cheers,

Laura

Penn (not verified)

And to be clear, it was your video I was referring to when I said I was exhausted just watching!  But I don't have a marble rolling pin, or a marble pastry board, and I do have a car and a lot of plywood, so I was hoping my automotive mangler might work.  I'll just have to try it, once I get enough woven of a mangleable material.

Sara von Tresckow

Using the hand mangle that Kerstin and I described does not require "brute force" - by leaning onto the mangle board with body weight, one simply pushes the roller with weight on it.

The car idea is not a good one - mangling cannot be effectively done with a flat piece of cloth - it needs the rolled up piece with layers moving slightly against one another. I once put a piece that had been done with the marble rolling pin in my electric mangle and got a significantly smoother and flatter piece as a result. Also, driving back and forth would not give you any particular control over which sections were mangled how much - the process needs to be evenly distributed across the entire piece of fabric.

Lately I recommend a steam generating iron with a tank (tailor's iron) as a decent substitute for the mangle. These use a dry steam and smooth fabric much better than even a Rowenta Professional model. The one from DeLonghi is reasonably priced, and when I am in a hurry, I use it on my linen tablecloths instead of the mangle with good results.

If all this is too expensive or too much effort, just steam iron your fabric and be done with it.

 

laurafry

As Sara says the process looks more physically active than it really is.  :)  You don't *need* a marble rolling pin, that's just best case scenario.  There is the ideal, then almost as good.  An ordinary rolling pin will do a respectable job, or just a large dowel, could be a pvc pipe.  It's the idea that the threads become compressed and flattened that matters, not so much how that is achieved.

By all means, try driving over the cloth - it might work well enough.  :)  I've been tempted to try it too, but haven't done it - yet!

cheers,

Laura

Penn (not verified)

I'm pretty much dissuaded, with the two factors--that the physics of the car aren't right to actually mangle the fabric, and that it requires less effort than I'd thought.  I certainly have enough weight to apply to the task, so I might as well try the orthodox method before ruling it too taxing. 

laurafry

It's faster than doing a hard press, too, so less time standing over a hot iron.  ;)

cheers,

Laura

EvaHall

I have learned that linen should be cold mangled, because heat, especially in combination with moist will damage the fiber. While cold mangling makes it stiff and shining. I can add that I have some old linen tablecloths (not handwoven) that have become soft and sloppy.

 

Eva

bcham (not verified)

I used to mangle linen towels with a maple rolling pin on our kitchen spruce top table. The towel hems and selveges left permanent imprints on the table! Make sure to use hard wood or other hard surface for this task. Wondering? I once wove a long linen stripe of fabric I intended to use as a mangling cloth on the hand cranked mangle I now use and it left imprints of its structure on the mangled piece. I now prefer to run pieces directly through between the bare rollers but it's one pass at a time instead of being able to roll continously until ready. Should mangle cloth be made of cotton? or just woven very tight? Also, is there a method when using a mangling cloth to avoid a towel hems leaving a line where it's meeting the next layer? Thanks, BenoƮt :-)

kerstinfroberg

is typically a wery tight linen in plain weave (in Sweden, anyway). I have tried cotton, but didn't think it gave as good results. (I tried to find a good picture, this is the best I found... clickable, but not much better)

And no, it is not possible to avoid imprints of hems and such, if you roll it, in my experience.

the busy weaver (not verified)

Thanks for everyone's help! The "roll it one direction" is very interesting. The first time I learned about mangling was in a class with a couple dozen people and we were pounding away with blocks of wood and were under a tin roof so it was nearly deafening and very time consuming! Glad to hear all your suggestions! Can you tell me how to tell when a piece has been sufficiently mangled?

laurafry

My rule of thumb (literally) is that when I rub my thumb and finger over the cloth I do not feel individual threads but cloth.

cheers,

Laura

kerstinfroberg

but, anyway: for best mangling results the fabric has to be slightly damp. If it is too wet, it will dry to feel paper-like, and if it is too dry it will not get that nice and shiny surface. IMO the "best damp" is when it hasn't quite dried from the washing. If you dampen it after drying it has to sit for some time to let the damp even out.

And, of course: if you don't like the result, wet it out  and mangle again.

laurafry

That has been my experience, too.  :)

cheers,

Laura

Submitted by Anonymous (not verified) on