Help!  I'm putting a 100 yard warp onto my Newcomb Studio with a sectional beam, and I'm going to go wackadoodle if I have to count to 100 fifteen more times as I fill the rest of the sections. (I realize this warp will probably be longer than 100 yards.  That's ok, as long as all the sections have the same number of rotations.)

I'm using a home-made tension rack (built for continuous warp weaving) and I'm not sure that a Leclerc yardage counter would work with it.  Don't have $103 to solve the problem, either.

I thought about using a string around the outside of the beam's shaft, where the handle attaches, but so far, I haven't been able to get that string to wind up reliably and it quickly gets in the way of the handle.  I don't see any other place on the beam where I could wind a string that would unwind easily or slip off when I'm ready to start on the next section.

I'll admit there's a certain amount of meditative value in surrendering to the count...

Any ideas?

thx

Comments

WeaverDave (not verified)

Would you be able to "walk" the thread out to 100 yards, and then wind it back up onto the sectional beam?  As long as you have the 100 yard measurement correct, you could then temporarily wind it up onto a large spool or cone, and then transfer it to the sectional beam.  Interesting problem.  :)

karentiede

Do you mean, take one of the warp threads out for 100 yards and then wind it onto the beam until it's gone, then repeat with a different thread in the next section?  100 yards from my loom is somewhere in my neighbor's back line, I think...

mneligh

I use business cards between the layers.  Count out the number of cards you will need and stick them in, one each layer.  I have never done 100 yards, and the build up from the cards might be significant, so you might try something else, like narrow paper strips.  If you do this for each section, you will have the same number of rotations per section.

karentiede

It's certainly a good way to use up that stack of business cards!  I'm counting out 19 cards, and inserting one every five rotations, so I have to count to five 20 times each section.  That's way easier than wondering if I just skipped from 57 to 67.  The sections with cards clearly gained a little height over the ones without.  Will have to see if it makes any difference to the tension.  I can afford fishing weights for every warp end on this set-up.

Now I have to hope my friends don't notice their cards in my loom.

Thanks!

Sarah D

Interesting article, but I'd have to disagree with the blanket comment about the inaccuracy of fishing line counters. I've been using one for years now, and find its accuracy is relative to how well the user controls it. Clamped on a table (or fishing rod) with the yarn/line simply passing through it most likely wouldn't achieve a consistently accurate result. It really needs a bit of downward pressure  on the measuring wheel (additional to the little clamp lever within the mechanism) to ensure that the yarn maintains contact with the wheel at all times. If a yarn is allowed to slip or skip over the contact point, then some of the yarn obviously won't be included in the measurement tally.  When I first started using it, I'd also weigh the resultant ball as a gross error check (knowing the metreage/kilo of the yarns concerned), but found the results consistently good, and more than adequate for my purpose of winding off 50g balls for retail.  

I hold the fishing line meter in my hand with the yarn wrapped around my hand in a way that ensures constant contact with the measuring wheel. If I were going to try it attached  to something, you'd still need to devise a threading path (maybe with a series of screw-in metal eyes?) that would produce both the necessary tension/drag as well as pressure to achieve consistent good measurement.

I'm currently using my fishing line measure to measure 10 separate ends of 10/2 cotton weft, which I'm then going to twist/ply together through my spinning wheel to make one thick corded weft for a warp rep project.

As a cyclist who already uses an electronic odometer on my bike, be aware that they too can been subject to inaccuracies and false readings for a variety of reasons. So whatever way one chooses to measure yarn, I'd still suggest incorporating a gross error check if reasonable accuracy is important.

Margery (not verified)

When I warped my AVL - 60 yards + I never used a yardage counter when winding on.  I did use one to count the yards as I filled the spools.  I first calculated the amount I need on each spool - usually two spools were needed for a 60 inch wide warp.  When winding on I measured the orginal circumference of the sectional warp.  I then wound on about 15 turns - measured the circumference again - recaculated the number of turns and did it again every 15 or 20 turns.  Once I calculated the first section I knew how many turns I needed for each section.  I am not sure if this makes sense or not - it worked for me.

mneligh

Since sectional beams have a fixed circumference, you only need divide total yards / beam circumference to get the right number of cranks.  The need for a counter (in my case not a yardate counter) comes in when I'm turning the crank and I get interrupted or daydream or whatever and forget how many times I've turned the crank.  I think I can only count to 5 reliably.  I do use a yardage counter when filling the spools on my spool rack (mine was made for warping), and it's accurate enough, but that does not address the question of how much warp I've put on any given section. 

karentiede

Not sure I understand the comments about "filling spools;" I used 8/4 blend on 800-yard cones and simply wound straight off the cones till they ran out or got skinny enough to know they wouldn't fill another section.  Once I greased the axles, the warp beam turned much more quickly.  (Duh!)  Next time, I might go 10 rounds in between business cards.

Thx all!

mneligh

Not having done 100 yards, I have never had enough spools to provide all the ends needed in a 2" section.  If warping at 30 epi, that's 60 ends per section.  So I fill 60 spools in my spool rack with enough warp to provide the number of sections times the length of warp required.  Lets say, to make the math easy, 20 sections x 30 yards = 600 yards.  I use the yardage counter and electric spool winder to put just over 600 yards on each spool.  I move the the spool rack and the tension box from section to section as I go as I go, cranking the number of times I need to to get the 30 yards onto the beam  (which would be 30 if I had a 1 yard beam).

Does this help?

karentiede

Thanks--that helps.  I'm working at the other end of the scale--3 epi, tripled, for what I thought should have been 18 threads / section.  Next time, I'll know there are 15 sections on the beam (assumed there were 18, at 2", because it's a 36" loom...  silly me) and use 22 threads / section.  Not hard to afford that many cones.

Slipstream (not verified)

If you are using a warping mill you could set up a mechanical counter to count the number of revolutions.  Most mills have a set number of yards per revolution. It would be a simple installation with a mens of triggering the counter if you use a mechanical one. The counters start at about $10 US.  I you are using a warping board then you could use a memchanical counter to punch each time you go around your pins again there is usually a set distance you would use as a factor.  Just google mechanical counter and you will have a number of choices with different types of triggering and if you get really fancy there are electrical ones. Just make sure that you get a counter that can re-set to zero or else it would be a bit of a PITA to have to record the starting count each time.

Regards,

Charles

calebsb

I have done long (70-100yd) warps with a Leclerc (or similar) yardage counter and found mild to gross inacuracies in the final count.  I have also found the counters on commercial tube-winding machines to be ballpark figures at best.  I have never tried the odometer before but I think I will find one next time I do a long warp, just to see what it's like.  I have come to distrust such things when doing so important a task as warping.  The only thing that really worked for me was

1) to train myself to write down the current number every single time I caught myself thinking about anything or responding to any stimulus - this will get to be automatic after a while; also to sort of check in every five yards, write the number, check the spool racks for run-outs, and address any slopes or dips or humps that might be forming in the section.  On really fussy or slow warps I have been known to tick off every yard.

2) to remove all distractions, turn off the music, and SHOUT each number.  I haven't had a counting error since I started shouting.  Of course if you are in a workshop with other weavers, two people can't do this at a time.  At times when multiple warps were happening I would put on ear protectors and tick off every yard.

I have friends who keep a click-counter such as the lunch lady at a cafeteria might use.  They tape it to the beam so it requires little extra movement.  Of course they have to visually confirm that each click has advanced by only one full number.  All options still favor careful counting, unfortunately.  If you experiment with some type of counter please take notes and share you findings.  I am fascinated by all things related to warping. 

 

Laurie Dux (not verified)

I have just put on my first sectional warp an hoped for the best in counting the revolutions as I beamed on. I guess I'll find out at the end if I got it right. Reading through all the suggestions has been very helpful for my next warp.

karentiede

I expect I'll be off +/- five yards across the sections, and am working to be pretty happy if the total yardage gap turns out to be closer than that.  That said, it will be thrilling in and of itself a) if I can weave this all off in the amount of time I want it to take, rather than "the rest of my life" and/or b) that the whole warp turns out to be weavable, rather than badly tensioned or twisted (let's just say there were some lessons along the way).

My friend bought a loom with a long warp, and a rug still on it, and found single dollar bills rolled into the rug.  The former owner had hidden her personal savings from her husband in the weaving.  I'd like to get this warp off under my own power...

Joanne Hall

There is a sectional warping film on the Leclerc website which would be helpful to anyone who wants to see how it is done.

Joanne

calebsb

Karen, I'd like to see a picture of your tensioning racks if you have one.  I use a homemade tension box and racks and am curious to see what your setup looks like.

karentiede

Here's what didn't work well:

The rack above is built to hold 340 cones, give or take, and the pegs are exactly horizontal, except when they tip downhill a little.  Suspect it was drilled by hand, without the aid of a drill press.  Cones kept falling off if I didn't chase them and push the back onto the peg.  Hard to do when you're trying to wind the sectional beam with one hand.

After I gave up on the rack above, I looked around the house for something that could be pressed into service and found the rack below:

I could fit 16 full cones on it.  Could have taken it apart further to hold a few more but it was pretty wobbly as it was.  I put the last two cones into coffee cans.

You can see the full-width tensioning rack to the left of the spool holder.  It was built for continuous weaving, with the spools on the big rack, but I am not sure it was ever used.  The man who built it loved building stuff...  (It was not built by the same person who built the big rack.)  The pegs were designed to mark warp stripes.

 

The little clothing rack collapsed after it filled 13 sections, leaving me to scramble with coffee cans and no end of headache for the very last section.  So far, the warp's OK, though.

 

 

 

 

 

calebsb

How would you compare the performance to that of a tension box with spool racks?

karentiede

This is only the third warp I've put on the loom, and the only equipment I have for warping.  Put the first two (10 yds, 4 yds) on from the front and decided that if I never warped again, that would be fine.  Ergo, 100 yards, and still thinking about continuous, although that rack takes up a lot of floor space.

calebsb

Yeah 4 yards of rack warping doesn't sound very satisfying and takes about the same amount of time as a long warp.  I will usually go to the warping board for less than 6 yards, buy I'm very happy with a homemade tension box and racks.  They are especially nice for "random" warps.  Now I just need to find a tube-winding machine that doesn't cost 15000 dollors.

ReedGuy

This is a counter found in a device we call a hip chain or string box for measuring slope distance in forestry and mining. I use them daily. As a hip chain application, a spool of 1000 meters of cotton string is threaded through an eye and onto that silver wheel. Three wraps are made so the string grips the wheel. Each revolution of this particular one is 10 cm or 1/10 of a meter. The counter measures to the nearest 1/10 meter in this case. You can get them for yards. The counter here is mounted with two screws into a plastic base which seated it into a hole in the string box. The box part just looks like a bate box a fisherman would use to carry earthworms to fish for trout attached to the hip with a belt. If you knew anyone in forestry they might have a busted string box laying around and chances the meter works.

Anyway just something to ponder. :)

corstan

I have a jack-type Nilus LeClerc loom and warp it with 45 yards.  My problem is trying to figure out how much warp is left on the beam.  I measure projects each time I cut them off the loom but the accuracy of what is left is not great.  As I get down toward the end of the warp, I have this fear I will start a 4 yard project and not have enough warp left to finish it.  I am not an experienced weaver so hope there is a simple solution.  Any suggestions would be greatly appreciated!

Sara von Tresckow

That is quite difficult. The takeup on a warp needs to be considered when measuring how much has been woven. So if you have 10% takeup and weave 10 yards, you've taken 11 yards off the beam. Since you don't really know the takeup factor until you measure the finished length of the project, it will be hard to know exactly. One thing that you can do is measure the circumference of your warp beam, note how many rounds are left on the beam and guestimate from there.

sandra.eberhar…

I wind extra threads in my warps to repair any warp knots or breaks with, and as these unwind as the warp is weaving, I can measure them and know how much warp I have used.

merlin1118 (not verified)

What about a simple knitting counter.  Just click for every revolution .  Cheap and easy

Carole M Cole

Knitting counters are notoriously inaccurate. I wouldn't trust any of them. 

Submitted by karentiede on