Hi,

I am a very new weaver and need help with understanding a draft for napkins. I have chosen to do a project from the Handwoven  May/June 2002 issue. It is on pages 56-58.  Can someone please explain to me how I thread the 3 ends on each end? I would like to know what threads go  through the heddles and what goes through the reed. I know that it is 2 per dent but, can you explain how they all work through the heddles and reed along with the other treads that are already shown in the draft on the ends?   I have gotten a different answer from several people and I am now completely confused. This is my first attempt at warping my loom. It will be the same for the placemats.

Thank you in advance for your help.

RF

Comments

ReedGuy

I will try to explain from this example draft. And strictly speaking of a vertical countermarch tie up.

In this draft the rows of boxes at the bottom, that are 22 boxes wide, are the threading sequence. Some are blank (white) some dark (black). The top row is shaft 1, the bottom row is shaft 4. It's like looking down on your warp threads from behind the breast beam. Each heddle on the shafts have one warp thread in this draft, indicated by each black box. So starting from the upper right on shaft one, the first heddle gets a thread. The next thread is on shaft two, the second row of boxes, the second box in from the right. The third goes into the first heddle on shaft three, the 3rd box in from the left on row three. The blank boxes are just spaces on the draft to help visualize the threading sequence and are not heddles that you skip. You can see by the 5th warp thread your are back at shaft one again. You have to follow this sequence in order, to get the pattern in your weaving. Just think of them black boxes as the ends of the warp threads. The 4 x 4 box in the lower right is the treadle tie up. The black boxes in it means a cord is tied from the treadle to the upper lamm for that shaft. The white boxes are the tie up to the lower lamm of that shaft. Upper lamms lower the shafts, lower lamm raise them. The short rows on the right hand strip there are the treadling sequence. One treadle at a time beginning at the bottom, treadle one in on the right of each row (4 treadles here). So in the first pick (throw of the shuttle) treadle one is pressed. Throw the shuttle, release, and beat. Next line, treadle two is pressed, throw, release, then beat.....and so on.  The colors there, cream on the bottom row of the draft and blue along the right margin are the warp and weft colors respectively.

ready fox

Thank you ReedGuy,

That was a great explanation for a draft. However, the project in the May/June 2002 issue, page 58, does not show the "last three ends on each side" in the draft.How are they threaded in the heddles and then through the reed? Do all three (on each end) go into one heddle then all in one dent of the reed? And do you add them along with the other end threads which are shown in the draft? I hope I am explaining this correctly. If you have the May/June 2002 issue, you can probably see it for yourself. It might make what I am trying to ask much clearer.

Thank you for your help,

RF

 

ReedGuy

Is there a repitition of the threading? Sometimes a draft shows several repetitions of the threading and the treadling. But what you might be seeing is similar to the draft I show, where the repeated sequence actually ends on shaft 2, and not 1 or 4. Weaving software will show it easier, that if you repeat those 22 threads across from right to left across the width of your loom the pattern repeats even if it looks like another heddle or two should be threaded to complete that sequence. If I included a wider draft you could see how it works. But in this draft, each sequence always starts on shaft 1 and ends on shaft 2. The number of ends you put through the reed depends on the set (ends per inch) of the warp and the dent count of the reed. Too many threads in a dent will cause troubles with the shed (opening for the shuttle to pass) and crowding. You need the proper reed for the draft your using. Sometimes your reed will allow 1, 2 or 3 threads in each dent depending on the yarn size and the dent (open space) width.

You thread ony one warp end per heddle unless it's a double layered weave, where you are weaving, say a 96" wide blanket on a 48" wide loom. This is done instead of piecing together 48" strips.

All threads go through both the heddles and the reed. You have to do this because 1, how would you create a shed (opening to throw the shuttle through) and two how would you keep even tension? Without a picture I can only guess.

loomroomcat (not verified)

generally what I do at the selvedge ends is put all 3 threads in one reed slot and then thread each into a separate heddle.  this makes your threads closer together at the sides of the cloth, just like the selvedge on a  piece of fabric you buy at the store. Makes a firmer edge and they generally look nicer too.  I do this for scarves and blankets, rugs, actually almost everything I weave whether it tells you to do it this way or not.

Sarah D

I've just had a quick look at the page and the instruction is to 'double the last 3 ends' at each side. The full pattern draft is as shown; it's simply putting 2 ends in each heddle for just the first 3 & last 3 heddles (and doubling up in the reed too so you're not actually increasing the width of the fabric). Think of it as putting in an extra thick thread for those 3 ends at the sides, as something that will increase the durability of the edges of the items when in use.

ready fox

Sarah,

Thank you so much. This is the info that I needed.

One more question please: When I put the threads through the reed, I should put two per dent plus one of the three extras for three dents. Is this correct? So that should be three threads each for the first three dents and then the last three dents as well.

Sincerely,

RF

Sarah D

I didn't stop to look at the sett etc but if, as you say, you're sleying across the width at 2 ends per dent (and assuming an even number of ends), then your first & last 3 ends (which are the ones to be doubled) will actually be in the first & last 2 dents. To achieve this you'd be putting 4 ends in the first dent, and 3 ends in the next dent - followed by 2 ends across the reed until you reach the last 2 dents - then 3, 4 to finish.

 

sarahnopp (not verified)

Is the design for overshot? that not showing the last three ends just lodged itself in my head and made me think of that.

ready fox

Thanks for seeing me through this Sarah,

OK, so you say the first dent will have 4 ends...does this mean two threads from the 3 plus the two where it picks up from the draft (on saft 1)?  Then the next dent will have the last thread from the 3 plus two from the draft (on shft 2)?

I am not sure about the "overshot" question. I'll be thankful if I can manage whtat I'm doing now. 

Thank you for all your help

RF

kerstinfroberg

I'm not Sarah, but I think "double the last 3 ends" means that each "working end" after the doubling will consist of 2 ends. The "working end" should then be regarded as one end.

ready fox

Hi kerstinfroberg,

I am a new weaver. What does "working end" mean and how does it relate to the 3 ends? If you could explain your email to me step by step it really would help. I know most of you understand these terms but it's all new to me. This is probably why I am having a hard time understanding this project.

Thank you everyone for helping.

RF

kerstinfroberg

As I see it, a working end is what comes through one heddle. The normal (I should say "usual") is to use one warp end per heddle. If you, for one reason or another, double (or triple) the end - that is use 2 yarns as one, through one heddle (or 3 yarns as one) - then you have a "working end" that is double (or triple) the thickness of the original single end.

For instance, I wove something where I wanted a thicker warp yarn that I had to hand. So I warped double the number of (required) ends, using 2 "as one" when threading the heddles. I still say that I sley at (for instance) 10 ends per centimeter, but will, if asked, qualify that to say I sleyed 10 working ends/cm, or 10 doubled ends/cm. In reality, I had 20, but I never "handled" more than 10. Clear as mud ;-) ? (if not, ask again, and I'll try a different explanation)

laurafry

I don't have a copy of the draft, but what *I* do if I am working with a fine or weak thread is to double the ends in the heddles.  (By end, I mean one warp thread - doublling the end would mean two threads in a heddle)

Then I keep the density the same in the reed as the rest of the cloth.  No, I would not increase the density in the reed at the selvedge as this may cause problems with the weft yarn not packing down properly. 

So, for instance, if the epi is given as 24 ends per inch, I would put two ends (threads) in the outside four heddles (only if it was a very weak thread), but continue to put two ends per dent in a 12 dent reed, regardless of how many ends were in the heddles.

As you can see, there are many answers to questions posed regarding weaving.  Usually the first answer to any question is 'it depends'.  :)

If I were you, I would double the ends (threads) in the outside 3 heddles on each side as instructed, keep the density the same in the reed - or double them as has also been suggested - start weaving and see how it looks.

Sometimes it is easiest to just jump in and give it a go, see if you like the results, and if not change what you are doing.  Using the area of the header is a good time to check for things like threading errors, sleying errors, or changing things like doubling the ends in the reed or keeping them the same density as the rest of the cloth.  Once you are satisfied all is going as you wish, then begin weaving the actual project.

For hints and tips you might find my blog of interest

http://laurasloom.blogspot.com

I also have a bunch of videos on my You Tube channel

http://www.youtube.com/user/LauraAnnFry1

cheers,

Laura

ready fox

Thank you Laura,

I am warping back to front. I started with two in each heddle at the end.  When I slay the reed will I put the two threads from the first heddle then the two from the next into the first dent? In other words, am I counting each of those heddles as "one" thread and still saying that this counts as two threads per dent?

Thanks for your help,

RF

 

 

 

Sara von Tresckow

Laura just said it clearly - 2 threads per dent in the reed. It does not matter if those two threads are in the same heddle or two different ones.

You'll get a few extra dents out of this in your total width, but it does not make a lot of difference in the finished product.

laurafry

I know it's hard to understand concepts in a text based format.  :)  But yes, two in the heddle, two in the dent.  Like I say, I don't like to change the density of the cloth in the reed at the selvedge as I've found it can cause problems with take up.  But the doubling of the ends in the heddles helps to strengthen and support the selvedge ends (threads) to withstand the tension as the shuttle is thrown and the weft 'seated' into the selvedge to create firm edge to the cloth.

However, whatever works, works.  :)

cheers,

Laura

ready fox

Hi Sara,

OK,  and if it does not make a lot of difference I should have enough warp on the loom to still complete the project. I'm feeling more confident now.

It has been a wonderful experience to start this project and to have the community of Weavolution to helping me along the way. Thanks again.

RF

Submitted by ready fox on