Hi,

I am just trying to get started with my Glimakra Ideal loom.  I have a tie up kit and have just started my first warp, using 2 shafts.  I have sleyed the reed but now I am finding that the shafts are hanging far too low.  I tried to adjust the cords that are on the pulleys but they seem to be far too long.  I am tying them up exactly as per the instructions that came with the kit.  In order to get the warp level I need to put the peg up so high that it interferes with the pulley action.  The heddles that I have are brand new and both they and the tie up kit came from dealers who knew my loom specs, so I am sure that they have given me the correct sizes.  The shafts are so low that they are banging against the frame of the loom.  I am really a complete beginner but I can't see how that could be correct.  Plus in pictures that I have seen they always look to be well clear of the frame.  I am sure that I am doing something wrong but just can't put my finger on it!

Does it matter if I tie up the texsovl in a different way from what the kit specifies, for example, if I use pegs on both sides of the cord that connects the pulley to the horses rather than a slipknot on one?

Could I be doing anything else wrong?

Any help or suggestions would be appreciated!

 

Comments

Sara von Tresckow

Check either The Big Book of Weaving or Tying up the Countermarche Loom to see a diagram of how the relationship develops between shafts, lams and treadles.

Also do NOT forget to put the locking pins in place prior to making any adjustments. This allows you to see exactly how everything is set up before you let the shafts, lams and treadles work with each other. If your setup is correct with the pins ink, it may be only that your setup needs a warp to balance out.

kerstinfroberg

For a counterbalance loom (which I guess you have, as you speak about "horses"), the old rule of thumb was to use left-over heddles to tie the horses to the shafts. Then you adjusted the cord over the pulley(s) so that the warp rested in the middle of the heddle eye.

I don't understand what you mean by "need to put the peg up so high that it interferes with the pulley action". The beauty of Texsolv is that it is infinitely adjustable - the peg(s) can go through any eye, as needed.

And, in case you haven't tied the warp on, do that first! All "balance" looms, be they CB or CM, need the (tensioned) warp to help stabilize them.

Edited to emphasize: "rule of thumb" doesn't mean it has to be a heddle, it doesn't even meant that the heddle's lenght is the "most correct" length... but it should give you the idea.

Kade1301

have very comprehensive and helpful instructions for setting up a counterbalance loom on their web site. (On the left-hand side, pretty far down).

On my loom (same model) the lower edge of the shaft is about 3 inches higher than the loom frame. And the cord that goes through the pulley is "too long" as well - the end is just dangling (that's the nice thing about the texsolv cords - with all the holes in them you can adjust them how you want them. There's no law that says that the slipknot must go through the very last hole in the cord ;) You could even cut off the end if you were 100% sure it really is too long - but I'd leave it for now)

Incidentally, I've found the Big Book of Weaving not any more helpful than Glimakra's free pdf-download with regard to getting a counterbalance loom to work smoothly (and if, after following the pdf, you still have questions, Joanne Hall might have specific tips for your situation).

on.niche (not verified)

Thanks so much everyone.  

Kade - That is really helpful info.  I have never weaved anything before and kind of 'ended up' with this loom (very gratefully!). So I have just been trying to bumble my way through getting it set up on my own.

I guess I was just being a bit silly, thinking that I had to put the texsolv pegs EXACTLY where I saw them in the picture.  I think that i will be able to do it now and just leave a bit dangling.

Submitted by Anonymous (not verified) on