Hi all,

I'm a new proud owner of an 8-shaft Loomcraft in pristine condition. (48" loom, bench, 10 hardcover weaving books, warping board, electric bobbin winder, original paperwork and manual, ten shuttles including an end-feed, and about 40 skeins and cones of yarn, total cost: 500!) It's already assembled and looks great. But I have a few questions as I've not used a Loomcraft.

My other loom has what I call a "full-on" apron. That is, the apron is a big honkin' sheet of cloth tied to the front and back beams, with a metal dowel on one side to tie/lash-on. The Loomcraft only has straps with a wooden rectangular dowel on the end. I'm assuming there's no need to make an apron due to this. At least I hope not. Also, can I tie directly onto these wooden rectangular dowels? I'm thinking it might be better to use lease sticks which then tie/lash onto the dowels. My concern is if I tie directly onto the dowels then they might bow and eventually snap.

Any suggestions on best practices for tie-downs on this loom? The previous owner used what appears to be some sort of smooth twine. The method involved lots of knots. I'm thinking of using Texsolv. I use it on my other loom with no issues. Any other things I should know about the tie-down process with this loom? 

Any advice and suggestions about this loom are much appreciated.

 

Comments

Kiiki (not verified)

Hi, I'm also a proud new owner of a Loomcraft loom. I have a 40" 4-shaft that I found on Craigslist this spring. I just love it.

I'll try to answer your questions. Yes, I just tie onto the rectangular apron rods. I haven't had any trouble doing that. I find warping front to back the easiest with this loom--with the back beam folded up and the warp beam removed, I can get right into the loom to thread.

For tieing up, I'm still using the snitch knots with the cords that came with the loom (plus a kind weaver on Ravelry that used to own a Loomcraft sent me the extra she had). But, I also bought texsolv, just in case. That seems to be what the few owners I ran across converted to. (Edited to add that I did convert  to Texsolv)

Did yours come with a pin to secure the beater bar when sleying the reed? Mine didn't, but I found a hitch pin at Home Depot that works perfectly.

Sharon

PS--that's a great deal you got! 

Su Butler

HI Weavin Steven....I have owned and used a Loomcraft loom for at least 32 years. I tie directly onto the front apron rod - the wooden rectangular piece - and have not had any problems. This loom was the only loom I used for production weaving for nearly 10 years. If you are doing a piece that is quite narrow, release the straps from the apron rod that are beyond the weaving width and the rod won't bow. I have never had to replace the apron rod, or for that matter, any part on this loom, with the exception of the front apron strapping when I foolishly cut right through it all in my haste to get a piece off the loom! I still use the original snitch knot cords to do the tie ups. These have always functioned well for me, but I do know some people prefer the switch to Texsolv cord. Loomcraft is a good, functional loom and I am sure you will have many happy years weaving on yours! Su :-)

Mymicahbear

I have a Loomcraft loom that must have a part missing. When I am sitting at the loom and use the foot lever to release the warp beam in order to advance the warp, the beam spins and unwinds my warp, there doesn't seem to be any way to make the pawl catch again and lock back in place. This can't be correct. Does anyone know what I need to do to fix this? Must I always stand at the back of the loom and release the ratchet wheel a couple of notches and then go back to the front to take up the slack?

Kiiki (not verified)

I'm not sure if I'm understanding your issue correctly. Is it the back brake that isn't catching for you? Do you have the spring that attaches to the metal bar? It pulls the bar back down so that it catches in the teeth of the warp beam brake.

Su Butler

HI Mymicahbear....you need to release the tension at the front of the loom with the ratchet and pawl that is attached to the front beam before releasing the back pawl. Use the lever that you use to forward the warp, engage the lever, move as is you are going to forward the warp, hold it in place, remove the pawl from the ratcher and then gently let the lever rest. Once the tension has been removed from the front, you can safely step on the brake release pedal and the pawl will disengage and the warp beam should hardly move at all until you use the lever to make the whole warp come forward. Forward the warp until is is about an inch or two from where you WANT the fell line to be, re-engage the rear pawl and then use the front lever to retutn the tension to the level you want it. This all sounds like a lot but it is really a pretty quick motion once you get the hang of it.

Weavin Steven

What Su says is right. When I first started using my Loomcraft not too long ago, it took a bit of trial and error to figure out how to use the ratchet system. I have another loom, a Leclerc Fanny, and it's a very easy warp advance/brake system. I find the Loomcraft to be not as fine-tuned a braking system as my Leclerc, but as Su mentioned, once you get the hang of it, it works just fine. One thing I'd add is that once you get the front warp beam ratchet released, a slight tap of the brake pedal is usually enough. No need to hold the pedal down. So: release the front ratchet/pawl, tap the brake pedal, engage the front ratchet/pawl, then tighten to your desired tension. There should be no need to go to the back of the loom to advance your warp.

Kiiki (not verified)

One more thought on your pawl not catching. I had an issue when I first got my Loomcraft where the metal bar (pawl) had a bit too much bend in it (for lack of a better word) and would snap over the gear and not drop into it. I had to go to the back of the loom and force it to drop into the teeth.

Pulling it back, away from the gear, straightened it out enough to solve the problem.

SMJF

Once when my husband was helping me put the warp beam back on, he lifted the bar too high and stretched the spring. I couldn't find a new one so I made a small muslin bag, filled it with washers or coins (I don't remember) and hung it from the hole where the spring attached. It works as well as the spring. I have learned to release some of the tension on the cloth beam before advancing the warp so that the warp beam doesn't unwind too much. Although it is good for me to get up and walk around the loom to crank the warp back a little.

Gwennie

I've just brought home a new (to me!) 40" 4 shaft.  It's a beauty.  If you still can I would like a copy of those papers from the Loomcraft company.  I'm a little nervous about the fact that these looms are no longer being made.  The hardward looks pretty straightforward, however, and I think most of it could be replaced with stuff from the hardware store.  Anyway, if I PM you my address would you mind sending me a copy.  I'll send my email too if you can do an attachment.  Thanks so very much!

Gwenn

Kiiki (not verified)

and sent the brochure. Hope you enjoy it. I don't have a manual, but haven't found it necessary. Don't feel nervous--it's a wonderful loom! I've been very happy with mine.

It's very similar to the Gilmore loom, which is still being made. If you are missing a part, it's possible you'll be able to get something comparable from there.

Gwennie

Su:  I'm about a foot into my first project and I see what the problem is here.  Regarding the lever used to forward the warp.  The pawl has to be reengaged by hand.  Should there be a spring or something to keep it in it's ratcher?  After I release it and do the adjustment to the back beam, I must return the pawl to the ratcher teeth by hand.  There is a hole in the top of the pawl...is that for a spring or something?

Su Butler

HI Gwenn....are you referring to the pawl on the lever at the front of the loom?  There is a screw that attaches that pawl to the loom and that screw can come undone with use....tighten i up enough that the pawl falls into the ratchet when you lift the lever, but not so tight that it is difficult to move the lever or disengage the pawl.  It should move freely and does not need to be engaged when you are weaving, only when you want to forward the warp or release tension so you can forward the warp.  

Best,

Su :-)

Su Butler

I do not know why this posted so many times!  Sorry!

Su Butler

<p>HI Gwenn....are you referring to the pawl on the lever at the front of the loom? There is a screw that attaches that pawl to the loom and that screw can come undone with use....tighten i up enough that the pawl falls into the ratchet when you lift the lever, but not so tight that it is difficult to move the lever or disengage the pawl. It should move freely and does not need to be engaged when you are weaving, only when you want to forward the warp or release tension so you can forward the warp.

Best,

Su :-)

Su Butler

<p>HI Gwenn....are you referring to the pawl on the lever at the front of the loom? There is a screw that attaches that pawl to the loom and that screw can come undone with use....tighten i up enough that the pawl falls into the ratchet when you lift the lever, but not so tight that it is difficult to move the lever or disengage the pawl. It should move freely and does not need to be engaged when you are weaving, only when you want to forward the warp or release tension so you can forward the warp.

Best,

Su :-)

Gwennie

Su and Michele:  Sorry I can't send a pic but I'm out of town right now babysitting my grandson.  The ratchet and pawl I'm concerned about are on the front beam. Following Su's instruction for advancing the warp: I disengage the pawl to release some tension then step on the brake release to open the brake on the back beam.  Then I use the hand lever at the front beam to advance the warp forward.  That goes great but I have to manually re-engage the pawl into the ratchet (front beam) to lock it.  Should there be a mechanism that secures the pawl in the ratchet in it's working position?  That way opening the pawl to release the brake would be done by pressing the pawl end but it would "snap" back into place.  My other two looms basically do this.  What do you think?

Gwennie

Michele: I've looked at this set of pics a lot.  Is the silver metal bar at the top of this one part of the foot pedal to release the back beam?  That part of my loom seems to be ok.  When I press the foot pedal the back beam releases.  It even spins a bit!  I've countered that by carefully releasing the pawl on the front beam ratchet by hand then releasing the back beam.  I just wish the pawl on that front beam would snap back into place and not have to be manually pushed into the teeth.  Does yours have a spring to hold it down in place?

Su Butler

HI Gwenn....the front pawl engages when needed...you may have to help it into place, but it does not need to be engaged for tension to be maintained on the loom. To release the tension, flip the pawl into the ratchet at about the highest level possible. You then raise the lever a tad, just to be sure the pawl is engaged, then you actulaly lower it to remove some of the tesnion on the loom. You may have to do this more than once if you are weaving under very high tension. Once the warp is relatively loose, you step on the brake, with your hand still on the front lever and the pawl still engaged, and let some of the warp off the warp beam. You forward the warp with your foot still on the brake, until the fell line is about 2" from the point you want it to be. Release the back brake so it can reengage, then finish up the tension setting with the front lever. This sounds a lot harder than it actually is, and when you have practiced, you will be able to do it in seconds without even looking at the pawl. You do not want to fix the pawl in the ratchet at the front, as if you do you won't be able to release the tension properly and your warp beam will spin out of control when you release the tension. Hope that helps... Su

Gwennie

OK.  I can sort of see it as I read the directions.  As soon as I get home to my loom I'm going to start practicing.  I'm sure I'm doing all these steps but in the wrong order!  I'll be home next week....stay tuned.

Su Butler

One more thing I should have added....when you engage the front pawl and move it up, you hold the lever with the cloth beam in that position, which is actually adding more tension to the warp, and disengage the rear pawl on the front ratchet by hand, then gently release the tension on the cloth beam.  After tension is released, step on the brake to release the warp beam so you can forward the warp.

Gwennie

Got it!  This may turn into a utube video!  

weavingone (not verified)

I just purchased a beautiful solid cherry Loomcraft loom. I haven't started using it yet and am looking forward to many happy hours weaving on it. So far, what I'm reading is that everyone is happy with their Loomcrafts. Does anyone have a manual or websites that cover Loomcraft looms?

Kiiki (not verified)

First, I had to laugh. I saw the picture above and thought, gee, that looks familiar. Of course it should, it's mine! ;-) That was the one and only time I tried warping sticks on that beam. :-)

I'm probably late to the party; I got knocked off-line by the hurricane. For the front pawl to engage, I had to loosen the screw that holds it. It was screwed too tightly, not allowing it to move on its own.

Gwennie

Kiki:  Thanks for the comment.  Sorry to hear about your being in the hurricane.  I went through Ike a few years ago.  Horrible.  I'll be home to my loom tomorrow and I'll be looking closely at the pawl/ratchet and reading all the comments.  I have a project on it right now so I'll be getting right into it.  I'll send a picture or write in the results when there is something to report.  And Kiki, if these are your pictures they are very helpful.  I was able to confirm that all the parts on my Loomcraft were in place and assembled correctly.  I hear you about the warping sticks.  I use brown paper.  Easy peasy.

Gwennie

I'm back at the loom and everything seems to be going just fine.  I'm following your excellent instructions and moving along well.  Thanks for all your help.  I look forward to posting a pic of what I'm working on. 

Su Butler

HI Alice....I purchased my Loomcraft loom new in 1980 and it did not come with a manual.  There is really very little learning curve associated with the loom.  Ask here if you have specific questions, and I am sure the many happy Loomcraft owners will be glad to help you out!

Gwennie

I'm weaving away and having NO problems with the brake, or anything.  The "spinning" of the back beam has completely gone away with release tensioning.  Thanks again for your help Kiki and Su.  I'll post this project when it's done. 

Kiiki (not verified)

So happy to hear you are weaving! I hope you will love yours as much as I love mine.

LShinn

I am babysitting a 46" cherry Loomcraft, 8-shaft, 12 treadles that I haven't used yet. It's set to go but there is no tie-up. Is there a particular kind of cotton cord that should be used? Never done snitch knots. I can't believe the owner was going to put the loom pieces out with the trash! It now lives in our living room till she decides she might want it again.

Gwennie

I pulled all the old snitch cords off my Loomcraft and replaced them with Texsolv cord.  Getting the cotton cords to be the exact length after cutting and tying knots was just too nerve racking and Texsolv won't stretch out.  I measured one piece of Texsolv cord and cut all the others to match counting the "eyes" to measure.  Loop the top end thru the second eye then use an "arrow" pin to secure the end of the cord through the treadle.  All you have is straight cords.  Clean and neat.  They are easy enough to change by pulling out the arrow pin under the treadle.  I got a spool of Texsolv and the pins from The Woolery but they are available lots of places. 

Submitted by Weavin Steven on