Can anyone help with countermarche tieups? I'm having the problem that when one treadle is depressed, the others ride up and stay up, making treadling uncomfortable/frustrating. The loom's a Noble 8 shaft.

Comments

loomroomcat (not verified)

do you have 8 cords tied to each treadle?  On my loom, the shafts I want to raise are tied to the long lamms and the unused shafts are tied to the short lamms.  Each treadle should be connected to every shaft, either to raise it or lower it.

loomroomcat (not verified)

Joann Hall from Glimakra USA has written a book for countermarche tie ups that is very helpful.  It has good pictures for each step of the tie up process.

Andy_SA

Yep, all are tied "correctly". I've tried making the ties longer all-round so the treadles hang lower to start with, but to no avail.

I did look into ordering the book, but international postage made it heaps more expensive! The other sources I have illustrate tie-ups well; there's something very simple I'm doing wrong - hopefully someone else has made this mistake and can clarify.

Andy_SA

OK... I'd decided to be clever and switch to texsolv cords for ease of adjustment. The texsolv slid through the holes in the lamms ok, but... I've just switched back to the thinner nylon cord for the upper lamms so that it could slide through the lower ones more easily. Seems that this was the problem; there was just a tad too much friction. Thanks for the suggestions and links.

kerstinfroberg

I'm a little late for this, but... Us Swedes (all that I kow of, anyway) - we don't take the upper lamm cords through the lower lamms - we either let them pass in front of or in behind of the relevant lower lamm. It is important to decide - all cords have to go the same way. (Myself, I always have them in front of the lower lamm.) Doing it this way, the lamms can pass each others, scissors-like, and thus give a bigger shed (if needed).

This is how I adjust my sheds: first do the preliminary tie-up. (After many years of using this loom, I know approximately how long the cords should be.) Next, I treadle each shed, noting which ties should be adjusted, looking mostly at the floor of the shed. Then I adjust one treadle at a time. I also adjust the lengths on top of the lamms (not under the treadles), because it is so much easier to see (and do)... esp when using texsolv cords. (And I use arrow pins exclusively - anchor pins are just a PITA. In my opinion.)

Andy_SA

Tack så mycket! Not too late as I'm still fiddling with cords and lamms. I'll certainly try what you suggested.

steve104c (not verified)

Joanne has a section on the GlimakraUSA web site that you can look at and just copy it. It is basic info. countermarch tie-up but you can see how to its done. Shows how to tie-up your lamms and treadles...........Steve.

Mike (not verified)

Loomroomcat as another newcomer to the countermarch loom have I understood you correctly?  Are you saying that with 6 treadles and 4 shafts I should have 48 (6 treadles x (4 x 2) upper/lower lams ) connecting cords between them?.........Mike

kerstinfroberg

I'm not loomroomcat, but I'll try to answer you anyway: each shaft should be tied to every treadle, either to rise or to sink. Thus, you'll have 4 (shafts) x 6 (treadles) = 24 ties. Depending on the pattern, there will be different numbers of long and short cords:

for an even-sided (2/2) twill + tabby, there are 12 short cords and 12 long, while for a weft twill + tabby, there are 16 long and 8 short cords:

(Long cord = from short (upper) lamm to treadle; short cord = from long (lower) lamm to treadle. Short lamms sink, long lamms lift.)

Hope this helps...

Mike (not verified)

Many thanks Kerstinfroberg.  That explains things for me.

Mike

Mike (not verified)

Theoretically or even practically, could you have all treadle holes connected to all lamm holes, i.e each treadle connected to each of the 4 holes on each of the respective upper and lower lamms, leaving the cord slack for those lamms that are not required to rise or sink.  In that way, you could just tension the required cord on top of the requisite lamm using texsolv cord and pegs.

Sara von Tresckow

24 ties are fine - you don't have to connect everything - unless your looms allows you to run the long cords through the lower lams on the way to pegging them on the upper lam. (This assumes that going through both lams at once doesn't cause too much friction.)

Don't try to reinvent the wheel - the traditional CM looms has functioned like a champ for several centuries now - it doesn't need Amaretto flavoring.

Martha

I'm a newbie.  I have a 4 shaft newcomb loom and just rewarped  it in a 4321... pattern all the way across, ending with 1.  I'm treadling 1234,1234...  The problem is that my weft is not wrapping around the end warp resulting in strands of warp showing on the selveges. Does that make sense?  Any help would be appreciated. 

Mike (not verified)

Thanks Sara.  I again plead newbie on a countermarch loom and am no way a re-inventor.  But theoretically with 6 tradles and 4 shafts, could not 1 of the treadles be required to lift 3 shafts and lower 1 and thus require 4 cord connections or conversely raise only 1 shaft and lower 3, thus requiring a different 4 connections, giving 8 per treadle and 48 in toto.  This assumes that a single cord cords cannot be routed through both lamms, and you would have to tie a cord  to the lower lamms and then route a second cord behind each lower lamm to the upper lamms.

Sara von Tresckow

Mike,

With 4 shafts, you can only have 4 ties to a given treadle. If you wish to change from 1, 2, 3 up and 4 down to 4 up and 1, 2, 3 down, you need to change the tieup physically. You can't have both combinations on the same treadle. Now, if you had 10 treadles and 4 shafts, you could have both sets of combinations. Each treadle can have no more ties than you have shafts operating for that project.

Sara von Tresckow

Martha,

You're experiencing something pretty universal. With a plain twill, it DOES make a difference which side the shuttle enters the weave on.

If you are entering your shuttle from the left side for treadle 1 now, try it again, entering your shuttle from the right side on treadle 1. Naturally this works only for a straight twil. If you are alternating directions, as in a goose eye or herringbone in the treadling, you'll need to consider floating selvages that catch every time.

Submitted by Andy_SA on