I acquired a 16 harness 56 inch loom and on my first tie up discovered that it is very difficult to raise 9 harnesses tied to one pedal!! While we consider options,(dobby, a tie up assist with pulleys, taking weight of some off those huge harnesses etc) I went back to what I originally wanted, which was 8 harnesses and wove a table runner which I am very pleased with. My question is this- 8-10 pedals is a stretch, but can be woven.  If you actually tie up sixteen harnesses, is it feasible to treadle 18 pedals and if so how do you do it??  I like to weave functional pieces and yardage, so I am interested in being able to weave with a rhythm, where I sit, treadle, throw the shuttle, change pedals and repeat.  Is there a trick or do I need to grow longer legs!!!

Thanks for your input

Cheryl White

Comments

Sara von Tresckow

Michael,

If, as it seems from your comment about raising 9 shafts on your new loom, it is a rising shed jack - you have hit against a major difficulty with this type of loom. As a little 4-shaft Baby Wolf or Harrisville 22" the loom type is quite handy. However, when the width is extended to near 60" and the shafts to 16 heavy frames, it becomes a cumbersome piece of equipment that is hard to handle. It is even far too exhausting for many weavers.

I have woven with only 8 shafts and up to 10 treadles - and found that past 8 you need some type of raised marker on a pair of treadles that don't hurt your feet as a sort of Braille system. Beyond that, I switched to a 16-shaft dobby.

Beyond 8Shafts/8(or 10) treadles and wider than 36", you really should be thinking dobby - for both efficiency and accuracy.

Small jack looms are fine pieces of equipment - the "big suckers" like you just acquired can be a bit difficult to deal with - and you should pay attention to what your body tells you when using it.

 

Michael White

Thanks Sara,

This is Cheryl, Michael's other half.  He does the posting on the web, but I am the weaver, so I posted the question.  Michael tried the pedals out and had trouble with the 16 harness tie-up and as you can imagine, I am not as strong as he is.   Since I was originally looking for 8 harnesses, I am still satisfied with the loom, but since the other harnesses were there, it raised the what if questions.

Thanks for your reply,

Cheryl

kerstinfroberg

My old CM loom had 20 treadles and a bunch of shaft sticks when I bought it. I upgraded to a vertical 16-sh CM, and immediately designed a 16shaft-20treadle  pattern - it worked, except the 2-3 treadles nearest the pivot point can be tricky. (But, mine is narrower, 115 cm - about 46"). It has rather narrow treadles, but, as it is a CM, that is not a problem.

Like Sara, I use some kind of "braille" system - something I change according to need for the specific pattern. I often use rubber bands.

lkautio (not verified)

Michael, my old Macomber had 10 shafts and 18 treadles, which took up most of the 40" width.  I occasionally used 9 shaft lifts, but could picture you using 15 on that loom.  You do build up some leg strength on a Macomber.  The treadles out to the sides can be challenging.  On a 40" loom the last one on either side was too close to the end to lift the shaft evenly, but it might be better on a 56". I had a chance to buy a 20S 24T 60" Macomber for $1000 but didn't think I could handle it without (noisy) air assist.

I would try counterweighting first, then look into air or electronic assist. Neither of the assists are cheap or bug free.  In the meantime, how you arrange the treadles makes a difference on body wear and tear.  Try to put heavy and much used lifts directly in front of you and light or less used lifts out toward the ends.  It may make your treadling a bit odd, but, weaving for mental challenge is a good thing :-) You might be able to swap out the spacers between the treadles for narrower ones so that the treadles are easier to reach and operate.

I ended up going to the countermarch computerized Weavebird (24 then 32 shafts) to get around the problems.

Laurie Autio

Michael White

Laurie,

Thanks for the ideas.  Michael is working on the counterweights on the 16S  So far it brings them up great.  We just have to find a way to make them go back down again!!  It is in the balance and makes the loom look pretty funky while we experiment (old sash weights, plastic pipe full of wet sand, lead weights and milk jugs-in combinations!!) but it may yet work.  In the meantime just weaving  a fancy twill and plainweave and basket weave in vertical stripes was such a thrill.  I have yet to explore 8 harness weaves so I am Happy!!!

Thanks again

Cheryl

Bonnie Inouye (not verified)

With twills on 16 shafts, I am normally lifting 7 out of the 16 on each treadle because I enjoy having two different faces to the cloth. Fancy twill tie-ups can be altered and most of the time you can manage with a maximum of 8. Always check the tie-up so you can lift the lighter face. Many other structures work in a similar way. Tied weaves are different- I love having more than 8 shafts for woven imagery and I want all possible combinations of the pattern shafts. That's why I bought the compu-dobby for my first AVL, which came with bars and pegs. Traditional treadles are challenging for imagery.

You might want to play with 12-shaft drafts and use the last 4 for neat edges. Or 10 shafts for damask.

If you find a fancy tie-up that is too lovely to forget, you can arrange the tie-up so the heavier lifting treadles are in the middle. That is easier on the body.

Bonnie

Submitted by Michael White on