Hi Everyone,

   I'm an engineering graduate student and I'm modeling fabric for my dissertation. I'm using finite element methods to model straight yarns deforming into their woven configuration. My model shows some forces on the yarns that seem large to me, although I don't really know if they are.

With the following fabric I predict 0.26 Newton and 0.44 Newtons on each yarn ( 0.058lb and 0.099lb).

If I multiply it out that's ~3lbs / in. Are these unreasonable forces in a looming/weaving process?

Fabric Properties*

Fabric: Undyed Saran

Yarn Diameter: 10.2 mil

Weave: Plain

Picks/in: 33.25

Ends/in: 31.5

Warp Crimp: 5.5%

Filling Crimp: 2.75%

*I took these numbers from 'Freeston et al, Mechanics of Elastic Performance of Textile Materials, Textile Research Journal, 1967'

 

Thanks everybody!

---Justin

Comments

Joanne Hall

Hi Justin,

I certainly cannot help you with your calculations, but you need to remember that the tension you can put on any warp threads will depend on many things.  And warp tension can change slightly when you advance the warp.  Some small looms with few teeth in the ratchet make it hard to even get close to the same tension each time you advance.

You cannot put as much tension on the warp on a jack loom as on a counterbalance or countermarch loom.  And on a jack loom, when you make a shed, usually every other thread (the ones raised) is tighte. 

The tension you get on the warp with 50 warp threads is far greater than you can get if you have 2,000 warp threads.  The depth of the loom is another variable as well as the size of the shed you want.  And on a rigid heddle loom, every other thread might be looser. 

If you are using a small loom as a model, these variables can be even greater.

Joanne

Joanne Hall

I only mentioned the different tension you get from one loom to another.  I didn't mention the variations in tension and take up (the word weavers use for the undulation that shortens the warp threads) that can come from different weaves.  And sometimes a weave requires less tension so that the undulations will occur more easily.

Joanne

B P (not verified)

Hi Justin

I pointed this question out to my husband (who lectures in Engineering), and he reckoned you needed to talk to a weaver who's loom is set up to monitor the tension on the ratchet that controls the warp, OR, a weaver who uses 'live' tension ie. a weighted warp.

It may be that some AVL loom weavers use live tension. You could post a question to the AVL Group here on Weavo. Hopefully someone there can help you out with your query.

You could also try the moderators of the Yahoo! group WeaveTech. They may be willing to post your question on the list there.

Good Luck!

Beth

Bonnie Inouye (not verified)

You list "fabric" as "undyed Saran".  A weaver would talk about warp yarn (or threads) and weft ("filling" is OK, just old-style) by giving the number of plies, the weight of the yarn (how many yards per pound or metric equivalent, not the diameter of the yarn) and the fiber (is it cotton or rayon or wool or linen?). The amount of twist has an impact but I don't know about crimp. There is more tension on the warp threads than the weft threads. What is Saran?

I weave on AVL looms and have no way to answer Justin's questions. Sorry!

Bonnie Datta (not verified)

I've woven with a weighted warp and find it requires about .5 to 1.5 oz per thread.  At 1 oz. per thread I get (about) the tension that I weave at on a regular floor loom -- all else (eg. type and size of yarn) being equal.  Like others who have posted, I'm not sure that this answers the question.

Bonnie.

 

Sara von Tresckow

Justin,

3 pounds per inch is not extreme tension on a warp. Industrial looms and yarns are made to withstand tension. Saran fiber is a synthetic that is rated to be quite strong.

Just FY I, the weave you describe would be quite open - your yarn at 10.2 mil would be about 97 wraps to the inch and you are putting only 33.25 per inch.

And for those here on Weavolution, I calculated the above sett calculation using the yarn description feature in Weavepoint7 where the yarn diameter (per inch or centimeter) is not the same as the warp space. Pointcarre, Jacqcad, etc. operate the same way. Industrial weaving DOES use yarn diameter in its calculations.

Karren K. Brito

The tension on each thread in the warp is small but since there are many warp threads, hundreds to thousands of them, the total tension is large.  For example bars used to tie warps on to the warp beam bow.  On looms that just have rachet and prawls on the cloth and warp beam and the are both on the right side of the loom, the warp is always tighter on the right side and looser on the left which tells me that the beams are twisting under the tension; these are hardwood such as maple beams 3-4" in diameter.

Sara von Tresckow

Know you what? This question definitely deals with industrial weaving equipment and allt he surmising about ratchets, table looms, short looms, yards per pound, etc. are not really on target.

The numbers presented are from a textbook for textile engineers planning to deal with weaving in a mill with power looms.

debmcclintock

Justinme, a Dupont fiber engineer helped me renovate a Deen rug loom from about 1895.  We may as well spoke different languages to each other.  Even though we both worked with looms, he was a mill engineer and had access to sophisticated mill equipment, I was a handweaver who worked with hand equipment and had some historical background.  We could talk to each other but spent a lot of time at the loom discussing what we each meant by pointing at the loom.  You might be better off looking for a mentor in the industrial fiber industry that has access to the type of measurement equipment you are referring to. I can guarantee that we handweavers don't measure the same way you are measuring. You are probably computing for a completely different loom and weaving process than what we have.   

Karren K. Brito

Is Allen Fannin still around, he is a textile engineer who could help you.  He used to help us handweavers too.

Joanne Hall

He died a number of years ago.  I think it was a car accident.

Joanne

lkautio (not verified)

Try Tom Beaudet.  He is a retired loom engineer (was very high level) and should be able to help. He is also the technical advisor for LeClerc handlooms. He speaks both mill and handloomese. You can tell him I suggested you contact him.

http://mysite.verizon.net/t.beaudet/

On a hand floor loom I weight individual broken threads with pennies in a film canister (or washers).  The amount of weight needed varies a lot, but for cotton or linen in setts of 20-40 ends per inch, lace weaves with a plain weave base, I come near to filling the canister with pennies. Don't know if it would be helpful, but I could weigh it fairly accurately if needed. I think your numbers sound like the right ballpark. My guess is that in addition to differences between mill and hand looms, fiber, and grist, the depth of the loom (distance from front to back) may make quite a difference. 

You may find some older information that relates to mills and force calculations if you go to the Griswold Digital Archives collection at handweaving.net.

Laurie Autio

tommye scanlin

A small mill run by Bethanne Knudson who has expertise in both industrial weaving machines and hand looms might be a source of information. She's also the director of the Jacquard Center. Tommye
Submitted by justinme on