I'am about to start designing, and drawing damask pattern, This is a completly new venture, I'am trying to get my design woven on a Louet Magic Dobby Loom on 24shafts, before getting my feet wet, where can I get advise on threading plans, and designs before going onto my own designs.

And how easy is it to design damask fabric on a dobby loom.

 

Ashleigh

Comments

Sara von Tresckow

Damask fabric can be one of two fabric types.

Drall damask is a block weave based on groups of 4 or 5 shafts and can easily be done on a dobby loom. On a 24 shaft loom you will have 4 blocks available - any geometry with that configuration can be used. YOu use either a turned 3/1 twill or a turned 5-end satin.

Patterned damask needs long eyed heddles and at least half heddles, if not a draw loom. It is not possible to separate the shafts of a dobby loom into two functioning groups as you would need. For this type of fabric you need a "harness" of ground shafts to make the fabric and some type of "pattern harness" to form your patterns.

Bonnie Inouye (not verified)

With your 24-shaft loom, you can use network drafted satin for patterns if you prefer not to use blocks. But I admit that the most beautiful handwoven damask that I have seen was woven on a drawloom in Sweden in fine linen, and it was very impressive.

Deb McClintock has done some satin on her dobby loom with photos under Projects. Have you woven blocks or stripes of 5-end satin on a regular floor loom?

Which weaving software do you use? You might want to start with a profile draft and block subsitution.

warpandweftware (not verified)

I use WeaveMaker, I have woven blocks on a 8 shaft hand-loom. I'am trying to advance my weave patterns from 8 shaft hand-loom.

warpandweftware (not verified)

 

To be honest, I've never advanced and further from an 8-shaft loom with simple twills, mock-lenos, blocks. So I’ve never tried network drafting, so can anybody help me what is the best place to find information for network drafted satin. I think I need to get some books. At University, we were never given this opportunity to weave this advanced, now I want to break the mould.

 

 


Eva (not verified)

I'm not that advanced myself, still weaving on a 16-shaft treadle loom, but you might find Alice Schlein's book, "Network Drafting: An Introduction" useful.  On page 56 there's a "damask" drawdown from cutting and pasting 1/7 and 7/1 satins in the peg plan and there's also a "damasse" from cutting and pasting 1/7 satin and plain weave.

Good luck!

Eva Stossel :) 

 

 

SunriseLodgeFi… (not verified)

I was designing and got stuck with something a little similar.  I can reccomend the best resource book (in my opinion!:) on the planet....Exploring Multishaft Design by Bonnie Inouye:)  Honestly....if you take that book step by step you'll be amazed at what you 'figure out'.  I have a 'damask' pattern that I've been working on for about a year now.  I recenly found out that I may be able to weave exactly what I wanted by using a different technique......taquete!  :)  Have fun in the research!  I'd love to see what you come up with!

Shannon:):):) 

Bonnie Inouye (not verified)

Wow, Shannon. Thank you! I wrote that book to help weavers who want to use more shafts than before (I was thinking about more than 8, but it does work for more than 4) and who want help with creating their own drafts. Chapter 5 is about network drafting but it's very brief. I've also written a little about his in an article for Weaver's which is in the book Twill Thrills. Alice's approach is different but I learned a lot from her. You can get Alice Schlein's book through Lulu.

Weaving software helps a lot, both for creating drafts and for really understanding how each part contributes.

Ashleigh, do you have a computer-assisted Louet small dobby or one with bars and pegs?  

Do you have a specific design ready, or just want to weave something in damask? If the latter, start with blocks.

Bonnie

debmcclintock

Here is a link to my draft that I used to work thru satin design and clean cuts for a sample exchange.  You might want to click on the pdf that has the sample page with the bibliography on it.  This is the page that went with the sample exchange.  In this sample I was trying to understand the basic units of satin and how they related to each other.  Each one of the books I found and referenced broke down satin into something that I understood for a beginner advanced weaver.  Also take a look at my sample pdf on the satin floral in my projects.  It shows how I took the draft above and applied more of what I learned about satin to another pattern.  Have fun and YES order Bonnie's book before it goes out of print.  It will help you think thru designing for multi shafts.  Something you have to wrap your mind around sooner or later OR reconcile yourself to spending the rest of your life trying to understand it!  

kerstinfroberg

To start with the obvious: as I am a Swede, so I have the Swedish definition of both dräll and damask. To me, a dräll pattern is always a block pattern, where the pattern is formed by the difference in warp- and weft-faced structures. Thus, the structures used can be 1/2 vs 2/1 twill, 1/3 vs 3/1 twill, 1/4 vs 4/1 twill etc, or they can be any satin. (To confuse the dräll, there is also "kypertdräll", a word not often used - "twill dräll" - sometimes used for complex twill patterns like "rose wreath", "oak leaves wreath" seen in Cyrus.)

Damask, to me (us) is always woven with the structure threaded on the ground shafts (3, 4, 5 ...), and the pattern is formed with either pick-up or some draw device - shafts or single-unit, like Sara described it.

So, what is the definition of "damask" that can incorporate networking? Is "damask" just another word for "complex patterning"?

warpandweftware (not verified)

Thanks for the advice I just was looking for you book Bonnie, but it either out of stock. Intrested in obtaning a copy. I've got a computarized dobby loom. Start making sense now of complex drafts. I think i'am understanding it now. after a few PDF, and weave websites.

SunriseLodgeFi… (not verified)

No problem Bonnie!  :)  Honestly.....your book brought me to where I am so far in my designs and it is written in such a way that each step becomes 'real' and 'gettable'.   I still have a LONG way to go!  I'd love to attend one of your workshops the next time your out east:)! 

laurafry

There is also a technique for using half heddles to extend the patterning possiblity of an 'ordinary' shaft loom.  I think Complex Weavers has a booklet by Noel someone that explains the process.

Yes, I've done it but probably 20+ years ago so I've forgotten the details, but it does work.  To make the up facing and down facing heddles we simply cut the ladders of TexSolv heddles as needed.  Wasn't ideal but worked to prove the principle.

cheers,

Laura

debmcclintock

Kerstin, it is good that you differientiated between drall pattern, and damask from your point of view.  As people learn from different cultures and increase their weaving knowledge they become aware of terms and sometimes use them incorrectly.  The networked term used in this discussion might be just a case of someone becoming aware of the different patterning techniques but not quite using them correctly. If you look back over this particular conversation it covers quite a few broad techniques that can take off in serious different directions.

We had quite an argument that went over one year in discussing the use of the term diaper within a museum collection.  It was very amusing (actually excruciatingly painful) but pointed out how museum curators, collectors and weavers look at terms.

Bonnie Datta (not verified)

I'm just working through Bonnie's book as I wait for my new 24-shaft loom.  I've only done 4-shaft weaving and occasional 8-shaft on my Structo.  But I've been trying to understand this statement from Sara's reply:

"It is not possible to separate the shafts of a dobby loom into two functioning groups as you would need."

How many shafts would be needed on a dobby loom to emulate a 2-harness, 8 shaft damask loom?  Or is this mostly an issue of the way in which damask patterns (threading and lift plan) are expressed?  How "big" (ends X picks) of a motif could I weave damask-style on a 24-shaft dobby loom (assuming just two textures, plain weave and 2/2 twill show)?  Is there a formula for factoring in the number and structure of textures as well as the motif itself?

I apologise for bouncing in here with so little understanding of what damask is, but I have this intense interest in structure and the way patterns are devised for various techniques.

Thanks, everyone.

Bonnie.

 

Sara von Tresckow

A dobby loom is consigned to weaving drall damask as described by Kerstin. The exception would be the use of half heddles.

What needs to be understood here is the definition of harness as a group of shafts working together to fulfill a single purpose. ALL the shafts on a dobby are controlled by the mechanism. They rise and fall as a single unit with many parts.

The second harness - or the half heddles - put EACH thread through a second heddle to allow it to move counter to the motions of the other harness. That is why clasped heddles or long eye heddles are a necessity for double harness weaving. The long eye allows threads to be raised anr/or lowered simultaneously. There generally is no sinking shed, but pressure exerted on those threads that form the shed floor.

That second harness needs to be separated by quite a distance to work. You can't bend the open shed in two directions if the shafts are all hanging close together.

See either John Becker's "Pattern and Loom" or Lillemor Johanssen's "Damask and Opphamta" for diagrams of the shed involved in weaving damask.

That is a common misconception when weavers purchase dobby looms with more than 16 shafts - assuming that throwing shafts on a single harness replaces the double harness is simply false.

 

Joanne Hall

The winter issue of VAV magazine, 1/11 has a section on damask, plus an explanation of the use of half heddles.  You can also read how the two harness loom works in Lillemor's book Damask and Opphamta.   If you take a look at these basic instructions, you will undestand the differences between the possibilities found wih a two harness loom, compared to a loom with one harness with lots of shafts.  If you want a copy, let me know.

[email protected]

Bonnie Inouye (not verified)

I have generally considered damask to refer to a cloth with a design made by warp-emphasis figures against a background of weft-emphasis figures with the structures being satin. On a dobby loom, a 5-end satin seems easier than others but I have not tried the other satins this way. If blocks of 5-end satin, 1/4 and 4/1 are considered damask, then why not other shapes?  Alice Schlein has woven examples in her book, Network Drafting. It is not too hard to make circles, for example, or hearts or leaves. If I weave leaf shapes of 4/1 satin on a ground of 1/4 satin, what would you call this structure, Joanne and Kerstin? To me, I want to be able to create a draft showing the design I want, expressed as the structure I need for the piece at hand.

My book is not out of print. I have some in a box here and I mailed two last week. My wholesale distributer ran out and I decided not to send more to them because they take a large percentage of the price. I am selling the remaining books myself. You can read about it on my website if you are interested.

www.bonnieinouye.com

 

Sara von Tresckow

Rather than surmise and guess at a definition, I'll quote Dorothy Burnham in "Warp and Weft"

 pp. 32-3

"Damask: A self-patterned weave with one warp and one weft in which the pattern is formed by a contrast of binding systems. In its classic form it is reversible, and the contrast is produced by the use of the warp and weft faces of the same weave, usually satin. By extension this term is also used for weaves in which two distince binding systems are employed.

In its classic form damask patterning is produced by contrasting the two faces of a satin weave. This suggests a shiny warp-faced satin pattern against an equally shiny weft-faced satin ground, with the exact reverse on the other face. Most silk damasks are of unbalanced weave with a fine, closely set warp producing a shiny warp face and a heavier, more widely spaced weft giving quite a dull apearance in the aras where the weft predominates. ... Linen damasks for table use are usually  balanced weave and completely reversible."

The networked circles, etc. in opposing satins is sort of damask - what is missing is the design freedom to place the desired pattern in continually changing places on the fabric as is possible with the drawloom. There I can independently make a large variety of shapes one after the other without rethreading or altering the loom setup. If I want cats marching across my cloth, I can do one on the right side, then one on the left side, then in the middle, and then a whole row - and that is not generally possible with the dobby mechanism as your threading is part of the determination of pattern. On the shaft or single unit drawloom, the ground weave is a straight draw - as is the pattern unit setup on the single unit - and the shaft drawlooms can be put in a straight draw that on narrow pieces imitates the single unit model.

kerstinfroberg

IMO there should be a clean cut at the shift from warp face to weft face. I'm not very experienced at network drafting, but it seems to me it would be difficult to get clean cuts on a network.

Burnham writes " By extension this term is also used for weaves in which two distince binding systems are employed." This is not true for most Swe weavers - we usually call this dräll - but obviously we are wrong on the international scene.

Also, Burnham writes "usually satin", which means that (drawloom) damask can be woven in twill(s), too :-)

Perfect circles cannot be made, as each "stitch" (unit?) is, well, a unit. Therefore all outlines will be somewhat jagged. One example of  a damask hanging picturing chickens can be seen at http://riksvav.se/kronobergsvav/engelska/mar07_eng.html (at the moment weavo does not allow me to make links).

I suppose damask could be woven on a shaft loom, too, if one has enough shafts. The smallest draw harness sold in Sweden has 10 draw shafts - using "ordinary" shafts I *think* 40 shafts would be enough if using a 4-end twill as ground structure. (I may be wrong... maybe 44?)

Bonnie Datta (not verified)

Thanks everyone for the explanations.  I checked a few of my books, and found a very nice overview in Zielinski's encyclopedia.  In fact, he gave answers to the questions I posed in my previous post, almost as though he was responding to it!

Bonnie.

Del (not verified)

And now, for something related but completey different. I work on a shaft-draw system doing figurative damask of my own design. I designed for yrs. on a program developed for me by a CAD-CAM dept. in a local college. The program is sadly outdated and will no longer interface with my computer and printer.

I need to know how I can design on a graph/grid base and then print the data as  "row and column" information. In other words, I need to know what shafts to draw to achieve my design, row by row.

I'm also semi-literate in the computer world. But give me info and I'll go find help. I think maybe some aspect Photoshop may work?

 

Sara von Tresckow

Any basic weaving software - PCW, Weavepoint, etc. will generate a "liftplan" for your damask when you enter the unit distribution for your pattern shafts as the threading and create the pattern using a liftplan. The liftplan has a column for each of your pattern shafts so you pull the designated square.

I normally work from an old PC and move the liftplan from row to row with the arrow keys.

Artistry

I agree with Kerstin that the clean cut is essential or else the threads are " jumping over" into the warp or weft satin. I 'm not sure I agree with Dorothy Burnham's (heavens , I never thought I'd say that!) assessment that " Most silk damasks are of unbalanced weave with a fine, closely set warp producing a shiny warp face and a heavier, more widely spaced weft giving quite a dull apearance in the aras where the weft predominates. " True I am limited in my knowledge to 3 block 5 shaft Damask, not the Drawloom. however I have always seen the warp satin and weft satin as equals in epi and in brightness. As you turn a piece of damask , what was bright becomes duller, what was dull becomes brighter. Of course one could always argue the point that as you turn the damask that weft satin becomes warp satin and vice versa in a simple block weave. However another characteristic of damask ( block weave) is it's riprocal reversal , areas which are weft satin become warp satin on the reverse side etc. epi being the same. I have woven satin in many fibers not just shiny ones. I still think it's one of the best structures around for showing off color :) Thank you Sara, for Burnham's definition and this most interesting discussion. Cathie

Artistry

See Irene Emery, The Primary Structures of Fabrics pgs. 133-134, for further definitions and interesting discussion.

Chris B

So drall is not a southern accent in the U.S.?

I'm just joking.  I arrived at this discussion after seeking a definition for drall so that I could better understand a pattern described in the No. 4 2015 VAV page 52.  It is titled Checked drall napkins in cotton & linen.  Very elegant napkins!  Thanks for all the expert comments. Weavolution is very fortunate to have you all on board.

Chris

kerstinfroberg

In some (older) Swedish books the word seems to be used as if meaning "patterned".

In those times, the dräll discussed above would have been qualified as "äkta dräll" (true dräll).

About other definitions, read more on my blog, here.

Submitted by Anonymous (not verified) on