I have been putting on longer warps, to save time by doing 4/5 projects on the same warp. My problem is in trying to keep a very accurate measurement of the completed weaving.  I've been using a measured cotton string, with knots to mark start/ stops.  Problem is that as I do more weaving, the string gets wound around the cloth beam out of sync with the finished fabric.  There must be an easier way to do this, but not mentioned in any of my books or reference materials. Thanks -

Comments

EvaHall

I tie  a bit of scrap yarn to the selvedge every 50 cm on my Glimåkra Ideal, and every 30 cm on my table loom. That way I can count the length of my weaving.

Ellen (not verified)

I do exactly the same as EvaHall and find it very easy to keep track of, except when I have woven very long pieces of fabric for curtains, when I had to begin adding little pieces of paper to the scrap yarn saying how many meters (yards) I'd got to :-)

loomroomcat (not verified)

I have a 3/4" vinyl tape measure that I attach at the start of my weaving with 2 t-pins.  So the 1" mark is at the start of my weaving.  As my fabric grows I leap frog the t-pins up to say the 6" mark.  The starting edge of the tape just hangs free, not winding around the cloth beam as I work.  As my fabric winds around the cloth beam, I just keep moving the pins as I weave.  Some of the 10 foot tapes are called flip tapes and the back side measures another 10 feet.  Very handy when weaving something large like blankets or yardage.  I use a scrap booking hole punch that is very small to punch 2 holes in the tape at 2" increments for my pins to go thru.  A pin goes down into the fabric, comes up, goes down into the first hole in the tape, up thru the 2nd and then back down into the fabric on the otherside of the tape.  Keeps me from catching my hand on the pin.  If this isn't clear, I can post photos.

Kiiki (not verified)

I use paper "yard sticks" that I picked up at Ikea. We were there buying a desk for my husband and I noticed that they have these disposable yard sticks hanging all over the store. One side is in inches the other in cm. Instead of throwing them out, I brought them home with me. I pin one on the side of my fabric and just move the pins as I wind the cloth. Works very well.

Cally (not verified)

I do something similar to Kiiki and loomroomcat, although my measuring tape is actually till roll paper. That's "till" as in "cash register": I bought a pack of the blank paper rolls from Staples about four years ago and am still using the first roll!

I measure off a strip and mark it in 12" intervals as a minimum, sometimes 6" intervals, or I can tailor the intervals to the design I am going to weave. For instance, if I am weaving a scarf which is to be the same at both ends, I can mark up the pattern or colour changes as I weave the first half, then turn the paper round to weave the second half. I have sometimes archived these paper tapes along with details of the project, as they are a really useful part of the documentation. Otherwise I re-use them until they fall to pieces.

I don't wind the tape onto the cloth beam, just leave the unpinned sections hanging free. My loom's breast beam has a cloth protector so I slip them under it for a modicum of control.

Cally

Barbara Keyser (not verified)

Thanks to all the great responders - I never thought not to wind the tape/ yarn onto the cloth beam with the finished weaving.  Great Big Help !!

debmcclintock

Barbara, I measure my cloth as I weave it.  Depending on the loom I have a string with either a 10" or 12" length.  I keep that string by the loom and when my cloth rotates below the front beam I measure my basic measurement and put in a pin.  I usually use a piece of paper with 6 pins in  it, for 10", 20", 30", 40", 50", 60" increments.  So, when I have used up all my pins I know I have completed one scarf.  Laverne's nifty keybob that she gave out at Convergence works nicely for keeping track of your pins as it has small icons on it that I can use to count with. TThis one has room for 7 pins or 70".  You can pick your unit. Here's the photo:

Sara von Tresckow

Try measuring for just ONE item. Fasten with savery pin. When the item is finished, go back to the beginning, remove the pin and start over at the beginning of the next item.

bsvertner (not verified)

I found vinyl tape measure to be too heavy and switched to soft and easy hem tape. It is 1/2" wide and 3 yards long. I mark it every foot and attach to selvedge with pins, advancing the pins so the tape is free of the breast beam.

SunriseLodgeFi… (not verified)

I choose a length....for example 10" or 20"....I place a straight pin with a large visible head at the 10" or 20" mark.  This way the pearly shiny round heads stay visible at the seam.  I also count out how many pins before hand.  If I'm weaving 70", I put 7 pins in my pin cushion.  When I get down to the last pin, I know to measure 10" from the previous and I've woven 70". Also, if I lose count I can see or feel for the pins if they are behind the front cloth beam:) 

 

illoominated (not verified)

I found some very inexpensive light weight 1 inch cloth ribbon on sale at one of the fabric stores.  I used a permanent pen to mark off and number one inch increments.  

Monica Bellas (not verified)

I actually use a piece of masking tape that I attach to the fell with the "current" measurement written on it.  As the fell advances to the breast beam, I measure again, add the additional inches, and move the masking tape to the next fell edge.

Bonnie Inouye (not verified)

I weave on a computer-assisted loom. When I begin a new scarf, for example, I weave 200 picks (it shows on the computer) and measure. This gives me an estimate of the ppi, picks per inch. Then I look at my draft on my computer with the correct epi and ppi to see if I need to adjust for aspect ratio, in case my design will turn out elongated or squished. I make adjustments, save, and resume weaving. After 200 more picks, I measure again to get a more accurate number of ppi. Now I know how many picks are needed for the entire scarf. Sometimes I plan for a special ending and other times just weave until I have reached the desired number of picks.  I also use my AVL to show when I have completed one yard- the woven cloth reaches a black bar on its way to the cloth storage system.

TinaHilton (not verified)

Deb - I love this idea of having the correct number of pins out for the length you want.  I clip a tape measure to the selvedge, but it does sometimes gets in the way.  I've tried using a string that's the total length I want, but once my cat chewed on one end without me knowing it so that scarf ended up short.  This way I can have a short length of string and know how far I've progressed and not have it in the way of weaving.  I'm going to give it a try with my next project!

debmcclintock

Tina, yeah, "the string" works for me, just don't use the pins for anything else!  Release the tension before you measure.  Or at least measure consistently under tension or not, just understand that under tension you don't have the relaxed cloth.  I've tried the tape, it fell off.  I've tried the long length of string.  I stepped on it and broke it. Or lost it on the cloth beam.  I've torn the Ikea paper tapes.  The string that fits the area between my fell line and the cloth beam works for me.  We all figure out what works for us.  I'm going to give Bonnie's ppi method a try.  Off to look at software to see how I can use that.  But there is always "the string" to fall back to.  

bsvertner (not verified)

Re: 'using pin with pearly round head'- The stickpin head can distort the selvedge, so consider placement of pin head outside the woven fabric. I appreciate Bonnie's comment. I'm scratching my head and wondering why I didn't assign this task to my software years ago??

steve104c (not verified)

I make rag rugs. Warp is at high tention. I use the piece of yarn in the selvage(hanging out the side) method, evey 10 inches. Just the other day I had 5 rugs wound on the fabric beam. But remember, when you release tention, the rugs contract and are about 10% shorter then when they are in tention. I have tried several methods but have found this one to be the best for me.

SunriseLodgeFi… (not verified)

Good thing to point out, bsvertner.  I keep the pearly heads so that they stick out of the side for that very reason.  There's nothing worse than something that's pulled on warp ends! :)

Karren K. Brito

I like 3 piece huipils (see one here), etc., which means that I need to weave 3 pieces that have matching patterns  so that I can sew them together (others don't worry about matching).  I pin a light colored hem tape to the 1st piece, under tension, and as I weave I make lines and label the different pattern areas.  I mark the begining and end of a brocade area for example.  This tape is then pinned to the 2nd and 3rd panels as they are woven and used to adjust the length.  For example if a leno area on panel 2 is slightly longer than on panel 1,  the end mark is moved to the end  of that band so that the whole panel doesn't get offset.   Pattern areas have to have a complete pattern even if it comes out slightly larger(smaller).  I just will ease the slightly wider into the narrower one when I sew them together, but the rest of the panel will line up.

emmysmom

How do you sew the three panels together?  I need to put two panels together for a project but I don't want the seam to be noticeable, and with a rigid heddle using the 10-dent heddle, I just can't seem to get a seam that doesn't pull the warp threads out of line.  

canaanmohair

How can you find out how much warp you have left on the beam?  Say you warp 36 yards and weave approx 28 - is there a way to calculate how much is actually left?  Yes I know I should have 8 but there is take up involved.  Sorta like a reverse counter.  I saw an AVL youtube of someone weaving with a heavy white string that was rolling off the cloth beam marked every yard.  Where is that tied?

 

 

Submitted by Anonymous (not verified) on