Does anyone know what is the right size Texsolv heddle to use on a (NZ) Thorpe 4 shaft countermarch floor loom?

Comments

Claudia Segal (not verified)

I had seen a discussion of this on Weavolution before so I searched for it under Forum post.  I found a comment from over a year ago with a link to a page that lists the heddle sizes and the loom.  Unfortunately, the link no longer works.  It was on the Unicorn publishers site and they may have updated their site and it changed.

There might be someone with the same loom, have you tried searching on the loom?  Someone else on Weavolution may have one.  The other choice is to measure the heddles you have and call Joanne at Glimakra or talk to someone at Halcyon Yarn or someone at The Woolery and they can usually help you figure out what will fit.  (Weavolution has a list of advertisers in the Resources section and you can call any one of the larger suppliers and they will probably be able to help out).  

Claudia

Joanne Hall

The breast beam height determines the space you have for all the moving parts.  The issue is to have enough space for the lamms to move without hitting the shafts or the treadles.  As a guide, you can use 11 inch heddles if your breast beam is at least 35 inches high.  If the breast beam height is about 33 or 34 inches, 10 1/2 inche heddles would be better.  If the bb height is less than 33 inches, the 9 3/8 inch heddles would be better.

Joanne

Joanne Hall

I visited your blog and I see that there will be some interesting classes taught in Australia.  And, thanks for listing my new book on warping.

Joanne

WEAVEblah (not verified)

Kind thanks, Claudia.

Yes, I have a copy of a list, like the one you describe;  unfortunately, the (New Zealand) Thorpe is not on it.

I notice that Joanne has commented too, with some good suggestions, and I will pass these on to the owner of the Thorpe.

WEAVEblah (not verified)

Thank-you Joanne,

We shall try this out.  I take it we should measure the height of the front/breast beam from the floor, and not from the lower front/foot cross-beam.

[This (NZ) Thorpe (4shaft countermarch) was constructed very much like a Glimakra 'Ideal' loom.]

WEAVEblah (not verified)

Yes, it's been a great year of weaving classes here.

And I've just received notice from my bookseller, that my copy of your new book "Learning To Warp Your Loom" is waiting to be collected;  happy days! 

As always, grateful thanks for your help.

Joanne Hall

The Ideal loom has a breast beam height of 35 inches and it comes with 11 inch heddles.  In the 70s it had 10 1/2 inch heddles and a breast beam height of 33 inches.  And yes, the measurement is from the floor.  I hope that my book is helpful.

Joanne

WEAVEblah (not verified)

Hi Joanne,

The Thorpe owners, who want to install correctly-sized Texsolv heddles on their looms, have measured the breast beam height with the following results:

Loom 'One' has a BB height of 34 inches.

Loom 'Two' has a BB height of 32.7 inches.

To complicate matters further, each loom (4 Shaft / countermarch / weaving width 120cm (approx 47 inches)) has been assembled with lamms (which by the way, are all one length), pivoted on only one spindle rod (not on upper and lower spindle rods, even though there are drilled holes in the frame for this method of installation).

How to proceed?

Are they advised to leave the lamms assembled on the single spindle rod?  Will this give them more space and allow them to use longer heddles?

Or, should they assemble the lamms on upper and lower spindle rods?  Will this give them less space, in which case they will need to use shorter heddles?

Will lamms, all the one length, work properly if installed on upper and lower spindle rods?

And, what heddle size would suit each loom?

I think, probably, it will be a choice between 280/12 and 268/12.

What do you recommend?

Thank-you, in anticipation of your help.

Joanne Hall

The lower lamms are sometimes called the balance lamms. 
They are necessary for the tie-up, making the shafts rise, but in addition, their weight is used to balance the weight of the shafts.  So, shafts and the upper lamms should be as light weight as possible.

When you are all tied up, pull out the locking pins as you watch the shafts.  The shafts should stay in place.  If they drop, then the lower lamms are not heavy enough to hold the shafts up, or the shafts are too heavy.  If the shafts drop more than one inch, you can weight the lamms to keep the shafts from dropping.  You can weave, but the dropping of the shafts will cause the treadles and lower lamms to rise.  Then it is uncomfortable to lift your foot up to step on the treadle.   The upper lamms will also drop.  This movement from the dropping shafts can cause lamms to touch each other or the treadles to touch the lower lamms. 

This may explain why all the lamms have been placed on one rod. But having them all on one rod makes the tie-up more confusing, and makes it difficult to add shafts.

The heddle size should be as you listed.  The loom with a 32 inch bb height might be better with 9 1/2 inch heddles.

Joanne

WEAVEdaze (not verified)

Thank-you Joanne.

There have been some delays in taking the steps you advise;  however, I expect, presently, to be able to confirm that the process has been achieved.

P.S.  I highly recommend your recently published handbook, "Learning to Warp Your Loom";  I find I am referring to it frequently, as the information, throughout, is comprehensive, practical, and easily applied.

Evie

I know I'm bumping an old thread, but when I went looking for info for the old Thorpe I was given recently, this is one of the very few resources I found specific to the issues I was having, and I just want to add some info in case anyone else finds themselves in the same position as me!

My Thorpe also has only one spindle rod for lamms, and all the lamms are the same length - however, they're made of two very different types of wood. Effectively, rather than short and long lamms, you have light and heavy lamms. Light lamms = short lamms, heavy lamms = long lamms. You can tell them apart visually by looking at the top of the lamm - one has a curved top, one square. The loom balanced perfectly on my first try. I am thankful to my partner for realising that they were of two different wood, and saving me a lot of trouble and heartache!

Submitted by Anonymous (not verified) on