These were in the crate when we unpacked an old loom.  I think this a homemade warp paddle and temple. (?)

 

 I'm not sure how the round hoop would have been used. A round rug? It's about 30" in diameter.  Any ideas?

Thanks, Jane

 

Comments

Joanne Hall

Some old rug looms have a flat metal piece like this for separating the warp threads for sectional warping without a tension box.  This is not what I would recommend doing, but perhaps this little piece was a home made version of that metal separating device.

Yes, the other is a cheap temple that would certainly scratch your loom if you tried using it.  It was made for rag rug weaving.

Joanne

Joanne Hall

It was popular in the 70s to make round wall hangings using a frame like this.  The frame stayed with the wall hanging.

Joanne

illoominated (not verified)

Your explanations certainly fit.  I was wondering how they might have done a sectional warping without a tension box.  The loom has a set of metal spokes that would have held spools and then a set of corresponding loops above them would have been threaded.  I've got so much to learn...

Joanne Hall

Sectional warp beams were commonly put on the looms which were made for rag rug weaving. This began about 100 years ago.  It was a design that was influenced by the textile industry.  Some of these rug looms used this simple guide rather than a tension box.  The reason this worked is that most of the rag rugs woven during that time had a sett of 12 per inch.  With a thick rag for weft, the warp undulated over and under the rag weft, making a lot of take up in the warp.  So, tension problems were taken care of in this take up.  If a warp thread got too tight, then it would just pull into the rag a little more than the others. 

But for weaving fabrics you need the warp to be wound onto the warp beam in a better way.  And it needs to be wound on tightly, so the tension box makes it wind on more tightly.  And there usually is a lease cross maker, an adjustable dowel to make adjustments in the amount of tension applied, a counter and two reeds, so that the warp will be winding on in a very orderly manner, with no threads overlapping their neighbors.  And the last reed makes the warp go into the section perfectly tight and flat.  That last reed is usually made so that it is right by the warp beam.  If there is a build up of threads in the center of the section, you will have tension problems.  So, you thread that last reed so that the threads have the exact width of the section.

Joanne

Joanne Hall

Sectional warp beams were commonly put on the looms which were made for rag rug weaving. This began about 100 years ago.  It was a design that was influenced by the textile industry.  Some of these rug looms used this simple guide rather than a tension box.  The reason this worked is that most of the rag rugs woven during that time had a sett of 12 per inch.  With a thick rag for weft, the warp undulated over and under the rag weft, making a lot of take up in the warp.  So, tension problems were taken care of in this take up.  If a warp thread got too tight, then it would just pull into the rag a little more than the others. 

But for weaving fabrics you need the warp to be wound onto the warp beam in a better way.  And it needs to be wound on tightly, so the tension box makes it wind on more tightly.  And there usually is a lease cross maker, an adjustable dowel to make adjustments in the amount of tension applied, a counter and two reeds, so that the warp will be winding on in a very orderly manner, with no threads overlapping their neighbors.  And the last reed makes the warp go into the section perfectly tight and flat.  That last reed is usually made so that it is right by the warp beam.  If there is a build up of threads in the center of the section, you will have tension problems.  So, you thread that last reed so that the threads have the exact width of the section.

Joanne

Submitted by Anonymous (not verified) on