Hello.... I am new here..hope this.is an OK question.... I have a rigid heddle loom....(I am a very new weaver) .... and I would like to make some ties for the men in my family.... I am not sure about how to narrow the tie at the part that goes around the neck...(a straight shaped tie is OK..... doesn't have to flair at the end, but I think it will work better if I can make it a little narrower at the neck part..... Any ideas would be very welcome..... I have googled and googled and not found anything...:( Thanks... ps linda(twiga)

Comments

Bonnie Datta (not verified)

I once did a men's tie in tablet weaving.  Because you can drop or add tablets you can do a shaped piece like a tie.  I dropped the tablets about 6 tablets in (not right at the selvedges) so that the selvedges stayed smooth and continuous -- kind of like shaping a knitted garment.  If woven on a loom then you need to cut and sew the tie, and it is cut so the weaving is on the bias which is not easy to do and it wastes a lot of fabric unless you do a few of them from the same piece.

Bonnie.

 

twiga (not verified)

sigh..... tablet weaving is a little beyond me at the moment..... I think I will try just weaving a narrow tie and see how awkward it is (or not) to tie.... thanks so much for the help.... tablet weaving interests me very much...someday soon...:)

sally orgren

At last, someone as crazy as I am to weave a man's necktie!

I started out as you, thinking a long strip. But actually, the tie hangs better and looks more "real" if you weave a rectangle of fabric and cut it on the bias into ever widening strips. And doing it this way, I had hardly any waste. (Okay. Even I was surprised!) Bonnie is right, it works best to do more than one.

I wove two neckties on a 15" wide table loom, just a few yards long (2-3) so I know you can do it on a RH. The trick is coming up with a fabric design that hides the joins well. The tip of the tie was at the corner of the rectangle. I used a tie pattern from the fabric store, laid it out on the finished fabric, and cut it each time it crossed the selvedge, allowing extra for joining the fabric to the next piece.

The reason there are squares at the end of the tie is that this was an entry for the cARTalog project, a challenge by the University of Iowa. One tie is in their permanent collection, and the other is in my father-in-law's closet!

  

 

sally orgren

In case it is hard to visualize the pattern layout described above, here's a *rough* sketch to give you an idea of how it works. (Okay, I guess I had a *little* bit of waste!)


twiga (not verified)

Hey Sally..... what a great looking tie. I will definitely have a go at this... thank you for the diagram.....at first I thought you meant I should weave a square and cut out a tie from corner to corner..... I NEVER would have thought of piecing it the way you did..... thank you! I'm off to rummage through my stash and find the perfect yarns for this... I will post the results...... Linda

sally orgren

Two other hints:

1) Buy the tie pattern first or make one out of tissue paper from an actual tie (adding seam allowances), and use that to determine how big of a rectangle you'll need to weave. (Width and length. Don't forget to allow for take-up and shrinkage between when the fabric is on your loom under tension and when it comes off and is washed You may lose an inch or two.) If your loom weaves wider than 15", you may need to do less piecing than I did.

2) I made a copy of my finished fabric on the copier, as a complete rectangle at 100%. (Yeah, I had to make it from 8.5 X 11 sheets, and then tape them all together in proper order.) But that was the safe way to figure out the exact cutting. I practiced on the layout paper copy first, and then I was ready for the real fabric and knew exactly how I was going to do it!

Please post your progress...I am sure there will be other crazies like us who will want to try it too!

Slipstream (not verified)

Your Father-in-law is a lucky man, Sally.  As a man who wore ties most of his professional life I always enjoyed a variety of ties and I would wear that tie in a heartbeat. Most men have a hard time including a little personal style in the average professional wardrobe and for me ties are an excellent place to get a little wild, well, just a very, very little. I liked knit ties which weren't that hard to come by but this tie looks great. Most of mine were reps and foulards. I always thought that a tie was assembled from the cloth one sees on top, a liner and I guess some material to stiffen the tie inside and make it drape well. Interesting to see this approach. Great looking tie Sally!

Regards,

Charles

weavinfool (not verified)

It looks very, very good!  Thanks for the picture and the process.

Bonnie Datta (not verified)

Sally that is fantastic.  Requires perfect edges and you've got them.  What I find most wonderful is that the twill line runs vertically -- perfectly.  Great innovation and a wonderful project for narrow looms.

Ellen (not verified)

Oh what a fantastic project! I really admire both all the careful thought and planning that went into this and the excellent outcome. Exquisite. 

I have long since given up the idea of making a tie, thought it would just never come out right, but this, - and thanks for the very thorough description - will make me think again, Sally!

Ellen

Ellen (not verified)

Hi again. I showed this to a weaving friend in Denmark, and the first thing she asks me, of course, is what yarn was used for this. I have looked at your projects page, Sally, and not found it there. Would you mind telling me. It looks great, and my guess is the choice of material would also play a role in how the tie turns out.

Karren K. Brito

Sally, this tie is wonderful!  Could you please post it in the projects so that we can find it more easily.

sally orgren

Okay! I'll try and post project details as soon as I get a chance.

tomrsey (not verified)

That's a great tie!!  I wore a tie for over 35 years of teaching.  I could go more than half the year without using the same tie twice!   Had a lot of fun with them.  This looks like a great project.

Submitted by Anonymous (not verified) on