I've just got a fill-in Lervad folding loom (until I move next month and have space for the big floor looms).

I'm relacing all the dodgy old loom cord with texsolv, and I'm just wondering: when doing a universal tie-up for a 4-shaft loom, all the ones I've read about put the two plain-weave treadles next to each other on the left, and the 4 twill treadles after them on the right. Is there some reason why not to have the plain-weave treadles at either end of the line of treadles, so you can work them with alterate feet? Both my sets of lamms (it's a countermarch loom) are pivoted from the left if that makes any difference.

Comments

kerstinfroberg

My first question: why do a "universal" tie-up? (And "universal" for what? There are so many structures you can't weave with a "universal" tieup...)

However, it would be a personal preference thing. Myself, I would never have the plain weave treadles on the outsides, 'cos I hate treadling with both feet... Many examples in Swe literature place them in the middle.

Re pivot points -  the nearer the pivot points the treade is, the harder it is to lower. So, what is "near"? What I can say is that my 115 wide loom has 20 treadles. I avoid, if possible, the 4-5 treadles nearest the pivot (even if that means that the tied-up treadles are not centered).

lkautio (not verified)

I'd consider direct tie-up as a more universal tie-up for a 4 shaft loom (tie one shaft to each treadle).  That allows you to weave all combinations by using two feet.  Other than that, it doesn't matter where you put the tabbies.  I'd put them where they make sense to you and are easiest on you and your loom.  The reason for putting them on one side is often one is alternating tabby with pattern.  Then one foot controls the tabby and the other the pattern shots, so you are always alternating feet.  However, a lot of common weaves fall outside this model, so you might want to change the position of the tabby treadles (or eliminate them) depending on the structure.

Laurie Autio

kerstinfroberg

 - but a "direct tie-up" is not optimal on a countermarche loom, only IMO, of course :-) At least, if trying that, do not tie for countermarch action - it will not work!

 

lkautio (not verified)

Good point!  I was thinking jack looms.

Laurie Autio

laurafry

How one ties the loom up will depend on the weave structure and personal preference.  :)  I think that having both plain weave treadles on one side makes more sense to many people visually, but it may make more sense to arrange them differently in order to weave more efficiently.  How that works for any one weaver will depend on how they think/visualize and move, physically.

cheers,

Laura

Joanne Hall

Often an author will choose to put the plain weave treadles consistently on one side, so that the reader can find them easily when reading the draft.  It has nothing to do with where you choose to tie your plain weave treadles.

I agree about ignoring the universal tie-up for countermarch.  Choose something to weave, plan a warp, warp the loom, tie-up the treadles as needed and start weaving.  Sometimes a new weaver can analize the situation to death.  So, just start.  You will learn a lot more after you have started to weave.  Joanne

padmavyuha (not verified)

This is the first 4 shaft loom I've owned, the others have all been 8 shaft countermarch, and it was a different setup to deal with. As it happens, this one arrived with the plain-weaves both on the right, and I was asking because when using my 8 shaft looms, I'd always found it more efficient to be using both feet more of the time (and less strain on the hips too) so I had my plain-weaves on either side, and my twills (I'm a big twill fan) in the middle.

I like the point that when weaving where you alternate between both, a different tie-up is more efficient - I'm just getting the loom set up so I can get on with some twill right now, so I'll stick with what I'm used to, which is:

1-3, 1-2  2-3  3-4  4-1, 2-4

The so-called "universal" tie-up that I've been reading about seems more to apply to counterbalance anyway, so some of my original question is redundant.

I will strive to keep the "anal" out of my analysing :).

laurafry

That's precisely the tie up I use on my Leclerc counter balanced loom (with rollers, not horses) when I'm weaving twills.  When the weave structure changes, the tie up may have to change.

Cheers,

Laura

janetdawson (not verified)

If you're weaving a structure where tabbies alternate with pattern treadles (overshot, summer and winter, bronson lace, etc. etc. etc.) it makes sense to have both the tabby treadles to one side so that you can treadle the structure with a walking tie up, i.e. tabby with one foot, pattern with the other. I usually put them on the left, but that's just due to muscle memory so my autopilot doesn't get confused.

If you're weaving a fabric where the tabbies don't alternate with pattern but you want them tied up for sections of cloths (such as hems?) then it makes sense to put them one to either side or in the centre so that you can treadle the plain weave alone as a walking tie up, and the main pattern (if there is one other than tabby) as a walking tie up as well.

I try to put the treadles I'll use the most hip width apart, so if I'm weaving just tabby on a four shaft loom, I'll usually use treadles 2 and 5 - or 1 and 6 if the treadles are narrow and closely spaced.

Just realized how super late to this thread I am - was surfing for any info on direct or skeleton ties up for a countermarche and here I am. ;)

Joanne Hall

The easiest way to make a direct tie up on a countermarch is to use elastic bands, just like on a drawloom.  The shafts hang from these elastics and you tie up the treadles as you wish, just one if you want.  It only takes one set of lamms.  It actually becomes a reverse jack loom. 

To make a skeleton tie-up on a countermarch, just work from the treadle tie-up of the weave to make the most logical tie-up.  Often you can have some treadles tied up in the usual way and only a few requiring two feet.

Is there a special weave that you are working with?

Joanne

Submitted by Anonymous (not verified) on