I've used the fast method of dressing my loom, and also the back-to-front method. I was wondering why the BTF method is so much more popular? The fast warp method seems to work just as well. Both methods get the same results. About the only downside to fast warping is that you have to tie on the "real" warp to the fast warp. But the rest of the loom prep goes faster than BTF so they cancel each other out. I imagine BTF is good for warps with short yardage. But am I missing something?

A few fast warp pros: no need for a cross, no lease sticks, no raddle. You could use these things if you wanted, but not necessary. I don't get crossed yarns and everything winds on fine with even tension. 

 

 

 

Comments

laurafry

If you are happy with your results, there is no need to change anything.

Cheers,

Laura

Karren K. Brito

Sounds like you are using a dummy warp and tieing the new warp on to pull it through the heddles and then wind on the warp beam. As a novice weaver I tried this once and too many knots came undone, it was a BIG mess.  I could probably make secure knots everytime now but have not tried it again. But I am tempted especially after I saw Jim Ahrens suggestion to tie on behind the harness.  I have to admit that a warp of slippery silk at 40-60 epi with no cross would make me nervous.

But there are reasons for every system , if one system did everything well -well, we would only have one system.

In my mind, dummy warps work well in production weaving where one is using a similar size warp on the same threading.  How could you tie on a new 40epi warp on to a 10epi old warp?  An if the threading is different for the new warp you have  both tied-on and threaded the heddles. No time saved.

I like to warp my floor looms back to front.  I already have the raddles, and I like to handle the warp very little after making it to maintain the order I made in the warping process.  I slip a rod into the end loops of the warp, lash that to the warp beam use the raddle cross to spread the warp, put a top on the raddle.  Then I stretch out the warp as far as I can and attach weights to it.  Then I beam it on  quickly and smoothly, only stopping to move the weights to the end of the warp.  By keeping the warp under constant tension the warp stays orderly and parallel, no tangles,  no broken warps.

Then I have a friend that like to do random warping , front to back.  She uses up odds and ends from her stash by placing it in the reed and then measuring out the lenght.  This is composing the warp at the loom.  Front to back works great for this. 

Some looms are more comfortable to thread in the back, others in front. This is because of the space, place you can sit or removable beams.  I like to get the heddles at near eye level so I can see the threading pattern easily.

The system that you feel comfortable with  is the one that works best for you and practice makes it easier.  It is an investment of energy to change, once you have a way that works,  and most of us need a reason to make that investment.  In the end , as the self-taught, inventive  woman in her 80's explained to my guild members when they asked her if she warped B2F or F2B,

" You just have to get it through the middle of the loom in the right order".

It is good that you have system that is working for you.  Enjoy warping and weaving!

tien (not verified)

Can you describe "the fast method"?  I don't know what that is, so I can't comment on the advantages/disadvantages of it vs. back-to-front warping.

jlread (not verified)

I'd also like to know what the 'fast warp' is?....I usually warp from front to back anyway...threading the reed from my hand holding the cross between 2 fingers...usually winding only 30 threads in a bunch....I must clarify here [winding meaning on the warping board not the warping beam]....JR

debmcclintock

Are we maybe talking about rigid heddle warping here in the 1st message. I think a "fast" warping simplification is being taught to rh beginners. Is that what we are talking about?

laurafry

Since this thread came up today I paid attention to the time when I went down to the studio to weave a shawl warp after dinner.

I arrived in the studio at 6:50 pm whereupon I rough sleyed the reed with a painted warp (I prefer rough sleying but it does the same job as a raddle).  The warp was 5 yards long, 200 ends, 20" in the reed.

The warp was beamed using a warping valet, then threaded in a straight twill progression, sleyed and tied onto the apron.  Bobbins were wound directly from the skein using a squirrel cage swift, and I was cutting the finished shawl off the loom (about 1000 or so picks later) at 8:37.  I was back at the computer by 8:38.

When warping a rigid heddle loom, I wind a warp on my warping board, insert lease sticks and lay them in front of the heddle.  Then I pull a loop through each slot and leaving the lease sticks in front of the heddle, beam the warp.  Then one thread is removed from the slot and threaded through the eye using the lease sticks as a guide to which thread goes where.  I tie on and weave.

I don't have a table long enough to give me a 3 yard warp, never mind a 5 yard warp, so I do it this way.  Works for me.

Each of us has to find the best process given their equipment, their space, their physical advantages (and disadvantages) and their budgets.  One way is not inherently 'better' than another, it is only better for the individual given their particular circumstances.

Unless - you are not happy with your results.  Then you need to look at other methods and see if one of them would suit you better.

I know what I prefer - but that's me.

I make no secret of how I do what I do.  Anyone interested in details is welcome to check out my blog http://laurasloom.blogspot.com  Labels are listed down the right hand side.  There are even a few video clips posted there although more are on my You Tube channel.

cheers,

Laura

Claudia Segal (not verified)

Perhaps fast warping is direct warping.  I direct warp most short projects (3 yards or less) on the rigid heddle loom.  I tie the warp thread onto the back apron rod and use a threading hook to bring a loop of yarn through the farthest left heddle slot being used for the project at hand.  You continue like this across the warp bringing the loop through the heddle to a clamped warping peg that sits across from the loom at the distance/length of your warp.  It goes pretty quickly and you beam the warp onto the back beam once you have completed this threading, measuring system.  I compare it to rough sleying the warp. 

I'm sure there are lots of YouTube videos demonstrating this method.  I have never used it on my floor loom and do not think it would work well.  It is best with short warps on the rigid heddle loom.

Claudia

sally_libby (not verified)

I will have to check out your blog. I takes me days to warp. I was hoping as I got more experienced that it would get faster. Sally

Grace McIntyre (not verified)

Hi everyone, I have been reading your posts about putting on a warp and I have come to the realization that I need more help.  I am a new weaver and trying to learn this on my own since I don't know anyone that weaves.  Is there a book out there or a video that nayone can reccomend that can take you through putting the warp on the loom.  I have done it but I am certain that there muyst be an easier and faster method to get the job done because if there wasn't no one would weave according to me.  It took me one entire evening to get a 188 string warp on and it didn't wind straight on the beam at all and I am not sure what I did wrong but I know I need to learn the proper way as to not get frustrated and decide I hate weaving.  If you have any suggestions please email me  Grace   [email protected]

sally orgren

For me, warping has been an evolving process. The more I learn, the better and faster I get. (Never pass up an opportunity to view a warping demonstration!) Knowing all kinds of techniques helps, because certain projects may call for a slightly different approach.

As Claudia & Laura pointed out, some techniques work better with small looms, and others with floor looms, or in studios with lots of space. I don't have a lot of space, so my techniques usually involve dual-use items that can serve many functions.

One trick I use to save time when beaming a small table loom. I set up my ironing board to its highest setting, and place the table loom on top. (Be careful, ironing boards can be tippy! If you are especially worried about the tippiness of the ironing board, just hang a few water bottles off the frame work of the loom on opposite sides of the board to balance.) You can either set the loom parallel to the center of the board, or position it perpendicular to the squared off back-end of the board. I want the edge of the loom with the warp bouts hanging down to just clear of the edge of the board.

Then I weight the warp bouts with water bottles (usually 16-32 oz for each 1-2" bout). I add loops of sturdy string to the necks of the water bottles. Using clip-style clothes pins, I attach the loop on the bottles to a loop I create in the bout, near the floor. The bottle is suspended just above the floor.

This gives you at least a yard (plus) of uninterrupted beaming before you have to adjust the water bottles again, lowering them back toward the floor. The clip-style clothes pins make this fast and easy, vs. untying knots and retying them. The steady and even tension provided by the bottles means all the bouts are the same, and keeps tangles at the rigid heddle, reed, or lease sticks to a minimum. You can focus on even beaming and adding packing paper as needed. 

After I write this, I am thinking hummmm.... I have a two-story entryway... what if I substitute the ledge for the ironing board...

(Oh. And it goes without saying to be sure to use PLASTIC bottles, not glass! ;-)

Sally

sally orgren

I think the Canadians have one over on us Americans when it comes to fast warping. I learned some of my best techniques when Convergence was in Vancouver and I took a workshop with Diane Mortensen. The premise was not handling the warp much, just as Laura mentioned. I was a *true* believer after Diane got 28 of us to warp our looms in the first morning of the first day!

This tip is for a someone who uses a warping board or reel to prepare the warp.

Diane suggested we don't chain our warps at all after winding. (OMG! was my first thought.) Her reasoning was that you are just adding twist and particularly with long warps, they will be more likely to get tangled as you unchain and beam.

She still had us add choke ties at intervals, but we just layered the warp bouts into ziplock baggies. The warp fed very smoothly and directly out of the baggie when beaming. (I should add her warps were 8/2 or 10/2 cotton, so finer than a lot of beginners would normally attempt.)

I have used this technique ever since, on short warps (3-6 yards) and warps between 9-16 yards. 

If I had the room, a valet or trapeze would be the next step, just short of the whole AVL system with warping wheel, computer driven 24 shaft loom, etc... (sigh).

jlread (not verified)

I really like the idea of the baggies...will do it on my next project...LUV IT !!!!!

laurafry

One reason I use a valet is because I have very little room.  :)  It also allows me to beam wide/long warps all by myself. 

And like Diane, I don't chain my warps, just drop them into a box.

cheers,

Laura

tien (not verified)

If I had the room, a valet or trapeze would be the next step, just short of the whole AVL system with warping wheel, computer driven 24 shaft loom, etc... (sigh).

LOL!  Not to tempt you further, but the "whole AVL system with warping wheel, 24 shaft loom, etc." doesn't actually take up that much space.  I have a 24-shaft AVL Workshop Dobby Loom, plus about four to five feet of space behind it - which is all you need for the warping wheel.  It all tucks into a corner of my 11'x12' crafts room.  (It is pricey, though since I bought all my equipment used, it was substantially less than retail!)

I use a trapeze made from sawhorse brackets for various purposes.  It works really well, and breaks down quickly and easily into storable parts, but you do need to make sure that the top is parallel to the back beam of the loom.  Other than that it works great!

kerstinfroberg

My valet (mounted on the loom) takes up about half the space I need for sitting down to weave... The valet hangs out about 30 cm (a foot) in front of the loom. Pictures here.

Michael White

I help Cheryl warp her loom. We put on a 17 yard, 30 inch, sett 20epi (600 ends) yarp of 8/2 cotton for dish towels BTF in under 30 min. Right now it is waiting for the heddles and reed to be slayed

 

  

Claudia Segal (not verified)

I'm ready to build a valet.  My loom is a Glimakra (looks similar to yours Kerstin).  How do you stabilize the wood pieces on the side of the loom?  I can probably use a PVC pipe for the top.  

Claudia

kerstinfroberg

The thing is: they don't need stabilization. I lean (wedge, if you will - but "leaning" is probably more correct) the lumbers between the cloth beam and the breast beam. It may feel a bit rickety (though I don't think so), but with the weight(s) mounted, the contraption is very stable

- make sure you get a stiff enough tube, if it sags in the middle it may create different tension between middle and sides.

Edited: between the *cloth* and breast beams!

Weavin Steven

I believe that what I'm calling fast warping is the same as using a dummy warp. That is, tying onto the back beam using a sturdy yarn of approximately two yards long. This length will vary depending on loom type of course. Then the dummy is threaded through the heddles and reed, from back to front. Then the real warp is tied onto the dummy warp. Finally the dummy and tied on real warp are beamed. The knot where the dummy is tied to the real warp is pulled through the reed and heddles. That's the trickiest part of the process. The smaller the knot the better.

sally orgren

Thanks for the clarification! One of my guildmates was just mentioning to me yesterday that Kati Meek has a demo of this type of method on her website. 

RE: Space issues, if only my Weaveatorium didn't have to serve as a guest bedroom too, with bed and dresser (plus floor loom, 4 table looms, yarn stash, etc. etc. etc.) I loved it when Sharon Alderman called it "sleeping loomside." 

Claudia Segal (not verified)

When I have used this method, I tied the new warp onto the dummy warp behind the heddles and left the lease sticks in the new warp.  I beamed the new warp and the threaded from b2f.  That avoids the "knots-through-reed and heddles" issue.  It also lessens the abrasion on a warp by beaming with just the lease sticks and not dragging it through the heddles and reed.

In addition, I found I had a few minor tension problems when I tied on in front of the reed.  Some knots pulled more firmly than others.  When I tied on behind the heddles, no tension issues at all.  

This is just personal opinion and experience.

Claudia

laurafry

There are a couple of very good reasons for using a dummy warp.  You can lessen loom waste if you are using a precious yarn for warp.  You can preserve a complex threading so that you reduce threading errors.  But it works best if you are using the same epi and threading over and over again.

Personally I've gotten efficient enough that dressing the loom isn't a huge undertaking, and since I rarely do exactly the same thing for warp twice in a row a dummy warp doesn't save me all that much time and effort.

But each to their own.  :)

cheers,

Laura

Submitted by Weavin Steven on