Hello! I'm a beginning weaver and just purchased a Kromski Harp, 16 inch rigid heddle. I'm working on the peg warp method, and have finished stringing through the slots. The next step is to cut, and then roll over the brown paper. I am confused about the relationship between the dowels and the rollers. Will I be rolling the warped dowel right in there with the roller, with paper around both, as I roll it? I think I'm missing something there. Then, on the other end, I will be cutting about 10 inches from the heddle and then moving every other thread through a hole, correct? Thanks for any tips. :) 

Comments

celtinbirks

Hi!

The rollers are called beams and the dowels are called rods.  Here is a really good video to help.    http://www.youtube.com/watch?v=2koGagZPLro  Yes, you will be rolling the warped rod (dowel)  right in there with the beam (roller) with paper around them both.  You should have two threads through each slot and then you will be pulling one of those threads through the hole next to it so you have one thread each in a hole and a slot.

Blessings!  I hope this helps!

Candace

clgy (not verified)

Candace, 

I'm so glad you were up; I can't thank you enough. It is now 8:15am and I am determined to get this thing warped so I can weave today. It's going to rain all day and I hate to waste a rainy day without breaking out my new yarn. :) I had a feeling that the rod should roll up with the beam, but I couldn't verify that in any of my books or online help. Thanks also for helping me with the vocab....it was late! :) I'm a calligrapher and have enjoyed my calligraphy newsgroup for over 10 years, so I was thrilled to find Weavolution and a place where I could ask for help at midnight. Thanks also for the link....I'm off to watch in now! 

Cindy

 

sewdoggie (not verified)

I actually posted another video, not seeing this topic. Good luck!

clgy (not verified)

Sorry - I am new to Weavolution and I wasn't sure if it was better to use the forum or the chat. I was desperate and it was midnite so I tried both:) 

Thanks so much; I just watched this video for about the 3rd or 4th time and I think I finally "get it". I'm going to be brave and go snip the yarn at the peg now, and just do it. One thing I still do not understand is how I can keep the tension even as I roll the threads onto the back beam, without a partner. My son can hold them tight this morning, but I would like to figure out how to do it when he is not here. Also, I just watched the beginning to weave video by the same man, and finally realized that I should actually start to weave before I worry about rolling anything onto the front beam. Probably obvious, but I think it was the last little step that I wasn't sure about. Nice to see how to tuck in the end from the first throw too! :)

I appreciate your help...thanks! 

 

Joanne Hall

I did not go to see the films, but I am wondering why you said you will cut and then beam the warp.  Maybe I did not understand.  Usually you just put the warp loops on the warp beam tie-on bar and then beam them on the warp beam.  When you come to the other end, you cut and thread the eyes of the heddle.  I know that there are different ways to warp the rigid heddle loom, but if you cut you will need to tie on to the bar.  That makes bumps on the beam, which you will immediately need to cover.

If you write to me at [email protected], I will send you a file by email which gives you instructions which are easy to follow.

Joanne

sewdoggie (not verified)

I assumed she meant the warp peg (used instead of a warping board or back of the Harp). That is what it shows in the video linked to above, to cut the warp at the peg. (peg is attached to a fireplace mantle far away from the loom)

clgy (not verified)

Hi Joanne, 

We chatted a month or two ago and you already sent the directions, which I have referred to many times in the last 24 hours! :) Peg is right; I was referring to cutting the loops off the peg, as I chose to do the direct warp on the peg method rather than using the warping board for this first time. Once I figured it out everything seemed to go fine. However, I am now disappointed and not sure what I did wrong. I am trying to throw the first few rows, and I was able to do one row in the up position, but when I move to the down position, I don't get a new shed. At first I thought maybe that was because I adjusted tension and tied with the heddle in the down position, so I tried moving it up and tightening the tension just on the first 10 yarns, to test that theory, but it didn't help. I think I remember reading somewhere that the heddle should be in the up position for adjusting tension and the final tying, but that it would be difficult to *have* the heddle in the up position at that point without it tipping over. I agree; it would have been almost impossible. What's the trick? I think it must be something else I have done wrong anyway, but I can't figure it out. Any ideas? 

clgy (not verified)

New problem, now that I am *almost* ready to start weaving:

I am trying to throw the first few rows, and I was able to do one row in the up position, but when I move to the down position, I don't get a new shed. At first I thought maybe that was because I adjusted tension and tied with the heddle in the down position, so I tried moving it up and tightening the tension just on the first 10 yarns, to test that theory, but it didn't help. I think I remember reading somewhere that the heddle should be in the up position for adjusting tension and the final tying, but that it would be difficult to *have* the heddle in the up position at that point without it tipping over. I agree; it would have been almost impossible. What's the trick? I think it must be something else I have done wrong anyway, but I can't figure it out. Any ideas?  

Karren K. Brito

So you are having problems opening a second shed, the down one.   So let's try some things until we get it fixed, can't be very bad or the first shed wouldn't open.

Can you tighten the tension on the whole warp by turning either the front or back beam?  Some times one shed needs more tension to open.  The whole warp should be quite tight rather like a drum head. When you have trouble  pulling the heddle up to open that shed(meaning you have to pull up with one hand and push down on the loom with the other) the warp is too tight.If that didn't do the trick, you need to check the individual warp threads for cross overs or threading errors. Look at one thread, start at the front beam where it is tied on and follow it straight back to the heddle, there should be no crossing over any other threads.  At the heddle there is only one thread in this eye( or slot) of the heddle, and then it continues straight back to the back beam with no cross overs or loops around any other threads.  Check every thread and make sure they alternate eye-slot-eye-slot in the heddle.If all the threads are parallel and tight and the 2nd shed still does not open I would retie the warp to the front beam with the heddle in a neutral position. By neutral position I mean neither up nor down , all the warp threads in the same plane.  You can just let the heddle dangle if you have to.

I hope #1 solves your problem but we have many  things to try.  If you try all 3 and still can't get  two clear sheds, post  pictures of the warp so that we can see what is going on. 

clgy (not verified)

Karen,

Thanks so much for your detailed suggestions. This is embarrassing, but I finally figured it out. You won't believe this.........everything was just fine except that what I thought was the "down" position was actually the "neutral" position.....I didn't realize I had to go down even farther! :) 

Ha! Sometimes it's just the little things. I now have about 6 inches done and it's looking pretty good. Thanks for your help! :) If I hadn't figured it out on my own last night, I think your suggestion number 3 might have tipped me off. I just love these groups; some day hopefully I can help some poor beginner too! :) Cindy
Submitted by Anonymous (not verified) on