I just brought home a new to me horizontal countermarch Glimakra.  The loom was advertised, described, and sold to me as an 8-shaft; unfortunately, it is not.  The loom has six treadles, 10 long lams, 4 short lams, and 4 pairs of shaft bars.  Since I can not afford to buy the additional parts I will need to convert this loom to an eight shaft, I am going to enlist my father into making them for me. 

The lams have me confused.  Should the number of short and long lams match the number of shafts or the number of treadles?  Ideally, I'd like an 8-shaft, 10 treadle loom.

Furthermore, does anyone have any theories as to why someone would put 10 long lams on a four shaft, six treadle loom? 

Comments

WeaverDave (not verified)

Was it an 8-shaft, but maybe you didn't get all the parts? 

Claudia Segal (not verified)

Can you post pictures of the pieces you think are long lamms?  On the Glimakra each shaft has 2 bars, a top one with a center hole and a bottom with a center hole. Is it possible you have only accounted for one piece for each shaft?  

For help with posting photos, check the Help section here.

Claudia

steve104c (not verified)

Maplecat, There are two bars for each harness. There are two lams for each harness. You can have one treadle for each harness or more treadles than harnesses. Most countermarch looms have two more treadles than harnesses so you can weave different patterns by tying-up  multiple harnesses to each treadle. Get in touch with Joanne Hall @ GlimakraUSA and get her Countermarch Tie-up Instruction Book. It is for your loom. I have a Glimakra Standard and got this book from Joanne. A really good book and a must. Good luck. I hope this hasn't totaly confussed you?..............Steve

Dawn McCarthy

Hi, 6 treadles would be for a 4 shaft (usually treadles are = to # shafts or plus 2 extra - 8 -10 for 8 shafts

slightly newer Glimakras have one set of long lams (lower) one set short lams (upper) and pairs of upper jacks for the cm.  So for an 8 shaft loom - 16 upper jacks for cm, 16 shaft bars (2 per shaft), 8 short lams, 8 long lams, min 8 treadles, preferably 10.  If you have extra long lams you could cut some down to make the extra short lams (lams have approx 11 holes in them) - new treadles are 32 or so a piece from Joanne @ Glimakra.  Email me privately if this is confusing and I can take close up pics to send.

Dawn

bloominloom-dawnmccarthy.blogspot.com

 

 

padmavyuha (not verified)

The Glimåkra 8 shaft looms more usually only have 8 treadles, even though the lamms are drilled for 10 sets of cords (which is confusing).

Dawn McCarthy

I think that might be dependent on the market it is sold for, here in the States they generally have 2 more treadles than the number of shafts.  

Dawn

EvaHall

I have often wondered if it would be possible to add two extra treadles  to my Glimåkra Ideal with 8 shafts. I would need to make some arrangement for fastening the treadles at the back of the loom, but apart from that it looks like an easy thing to do, as the lams have all the necessary holes.

Maplecat (not verified)

Thank you everyone for the information!  I pulled out my copy of Joanne Hall's Tying Up the Countermarch Loom and have been putting my loom together.  I must say the book makes a heck of a lot more sense with my loom in front of me than it did the previous times I read it!

I still don't understand the previous owner's set-up.  Ten long lams, enough countermarch jacks for a 10-shaft loom, and texsolv heddles that are two inches longer than recommended.

I'm going to cut down two of the long lams to make short lams.  It looks like the holes have the same alignment, there is just one extra hole on each lam I'll need to plug.  In any event, it is a little less lumber I'll have to purchase.

My first warp is just about done being measured and I'm excited to get it beamed.  My fingers are really itching to do an 8-shaft draft, but I'm going to go for four first as recommended.

 

Submitted by Anonymous (not verified) on