A new weaver here and I have a couple of questions.  For what type of projects/yarns/etc does one use a dummy warp?  I'm thinking of weaving some soft bathmats with some inexpensive yarn that can be washed and dried and am thinking this might be a good project to try dressing my loom with a dummy warp.  Any thoughts?

Comments

Claudia Segal (not verified)

A dummy warp is used when you want to preserve an yarn length with an expensive yarn or one that you have in limited amounts.  It sounds as though the warp you are putting on now could remain on your loom and become the dummy for a future more precious yarn.

For example, I used a dummy warp when I was dressing my loom with some handspun, hand dyed silk.  I wanted to preserve as much length as possible from the silk and the dummy warp served as my loom waste in that situation.

Claudia

loomroomcat (not verified)

I use a dummy warp on my blanket loom.  the loom is 90" wide and requires 750 threads for a queen size blanket.  When finishing a project I cut it off in front of the reed leaving 6" tails.  I then tie my new warp threads to the tails and pull the warp in from front to back for the next project.  Much easier to tie knots than to rethread every time.  I can change the colors of the warp but not the threading.  However different treadling allows me some variations of texture.  My dummy warp is two colors so making it easier to detect a threading error when tying on my new warp.  If I weave something narrower, I untie the warp from the back beam leaving it laying thru the heddles, weave my new project and then I can retie them to the back beam when doing a wider project.

Guiding Myth (not verified)

I use a dummy warp for slippery threads - which I love to use for certain projects.  But because they are slippery they would fall out of the heddles as soon as I thread them.

Otherwise I use a dummy warp to preserve a threading - for example a complicated threading where I've corrected the errors that I want to weave again.

Stephanie Stanley

sally orgren

I always keep a dummy warp rolled up and stored for when needed. I made it out of carpet warp, (cheap and strong) and it needs to be at least several yards long. You want the length to be greater than the loom waste at the back of your loom, allow the knots to enter the castle if possible, and be long enough to accommodate several projects. (You won't be saving much time if you have to wind a dummy warp everytime you need a dummy warp!)

In my attempts to get every last inch out of some warps, I have been known to tease the knots through the heddles, but typically have to stop before entering the reed. So on a floor loom, wth a dummy warp I can reduce the loom waste from 24-27" to just the amount needed to tie on in front (5-8"). If you are doing a fringed blanket, this can result in no loom waste at all, because the tie-on becomes the fringe on each end!

I loop the dummy warps over a dowel so when I am ready to employ, I just lash the dowel to the back apron, thread the dummy warp, sley, and then tie onto the new warp at the front of the loom.

My dummy warp is composed of several hundred threads. If I have extra threads I don't need for a particular project, I do not thread them. I just let them beam with the rest, making sure they stay out of the way of the active warps. When finished weaving, if I am not going to be using the dummy warp again, I trim all the warps evenly before removing the dowel from the loom, so it is ready to go the next time I need it.

I use paper towel tubes or gift wrap tubes, with a slit cut along the length, to store the dowel and dummy warps. The cardboard tube makes it easy to wrap the dummy warps around and keep them contained.

Dummy warps aren't going to be a panacea, and some may find they are more fiddly than they are worth. But it's a nice trick to have in your tool box when needed.

Bonnie Inouye (not verified)

Some weavers use a dummy warp (or just tie onto the previous warp) for a warp of fine, black or very dark yarn. It can be tricky to see that fine, dark thread well enough to spot a threading error, so this is mainly used with a complex threading. More shafts on the loom and a more unusual the threading are reasons to tie on and pull through. Other tricks for a black warp: increase the lighting near the heddles, sit at the best level to see the heddle eyes, and place something white below the shafts.

graciela (not verified)

Thanks! Very interesting question, and responses. Every day I learn something new in Weavolution.  Weave a nice day! Graciela

Submitted by Anonymous (not verified) on